How to service and repair the front lower control arm on 2000 Chevrolet K3500?

The necessary equipment for serving and repairing the front lower Control Arm includes the following tools: steering linkage puller (J 24319-B), torsion bar loading/unloading tool (J 36202), ball joint separator (J 36607) and lower Control Arm Bushing service set (Series 30) (J 36618), ball joint c-clamp (J 9519-23). You need the steering linkage puller (J 24319-B) alongside torsion bar loading/unloading tool (J 36202) and Ball Joint separator (J 36607) and lower Control Arm Bushing service set (Series 30) (J 36618) and Ball Joint c-clamp (J 9519-23). The service starts with vehicle elevating and using safety stands for support. Unloading the torsion bar requires the j 36202 torsion bar loading/unloading tool while marking the adjuster bolt for later installation before the adjuster arm's removal. Start by removing the outer Axle Shaft nut and washer from the hub assembly then follow up by taking off the brake caliper and brake rotor. Extract the lower shock absorber bolt from the Control Arm when you compress the shock absorber with the shock absorber. First disconnect the inner Tie Rod End from the relay rod using the steering linkage puller (J 24319-B). Next use the jack to support the lower Control Arm before removing the stabilizer link. First disconnect the halfshaft assembly with its attached cotter pin and nut from the upper Ball Joint then use the Ball Joint separator (J 36607) to separate the upper Ball Joint from the knuckle. First you must remove the lower Control Arm nuts with their washers and their bolts before taking out the jointed combination of lower Control Arm and knuckle. Users need to unbend crimps of the front bushing before extracting it through lower Control Arm Bushing service set (J 36618). During repair replace the lower Control Arm when the bushings on k1 and k2 vehicles require replacement due to wear or damage. Installation requires using the lower Control Arm Bushing service set (J 36618) combined with Ball Joint c-clamp (J 9519-23) to install front and rear bushings through proper crimping. Install the lower Control Arm together with the knuckle assembly but tighten all nuts to 165 nm (121 ft. Lbs.) at the specified z height position of the Control Arm. The technician starts the drive axle through the hub before joining the Ball Joint to the knuckle followed by Ball Joint nut installation to 128 nm (94 ft. Lbs.) torque before adding the cotter pin. Use the torsion bar loading/unloading tool (J 36202) to load the bar initially then mount the adjuster arm before installing the final bolt. Flush installation begins with the halfshaft assembly followed by the lower shock absorber bolt and stabilizer link before adding tire and wheel assembly and vehicle lowering and front wheel alignment testing.

OEM 2000 Chevrolet K3500 Control Arm

Suspension Arm

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Control Arms found

View related parts
2000 Chevrolet K3500 Lower Control Arm, Passenger Side
Part Number: 12470402
$1.67 MSRP: $2.61
You Save: $0.94 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm Kit, Steering Knuckle Upper & Lower Control; Control Arm
- Position: Passenger Side
- Replaced by: 15529829
- Item Weight: 0.70 Pounds
- Item Dimensions: 3.3 x 3.1 x 0.8 inches
- Condition: New
- SKU: 12470402
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet K3500 Submodels:
- Base, Cheyenne, LS, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
2000 Chevrolet K3500 Lower Control Arm, Driver Side
Part Number: 12470401
$1.67 MSRP: $2.61
You Save: $0.94 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm Kit, Steering Knuckle Upper & Lower Control; Control Arm
- Position: Driver Side
- Replaced by: 15529829
- Item Weight: 0.70 Pounds
- Item Dimensions: 3.3 x 3.3 x 0.8 inches
- Condition: New
- SKU: 12470401
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet K3500 Submodels:
- Base, Cheyenne, LS, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
2000 Chevrolet K3500 Lower Control Arm, Front Driver Side
Part Number: 19416906
$386.72 MSRP: $637.05
You Save: $250.33 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm Kit, Front Lower Control; Control Arm; Arm Kit, Steering Knuckle Upper & Lower Control
- Position: Front Lower Driver Side
- Replaces: 15665554
- Item Weight: 9.40 Pounds
- Item Dimensions: 22.4 x 18.2 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19416906
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet K3500 Submodels:
- Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
2000 Chevrolet K3500 Lower Control Arm, Front Passenger Side
Part Number: 19416897
Product Specifications
- Other Name: Arm Kit, Front Lower Control; Control Arm; Arm Kit, Steering Knuckle Upper & Lower Control
- Position: Front Lower Passenger Side
- Replaces: 15665555, 31022796
- Item Weight: 25.60 Pounds
- Item Dimensions: 22.1 x 17.3 x 5.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19416897
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet K3500 Submodels:
- Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
2000 Chevrolet K3500 Lower Control Arm
Part Number: 15988034
Product Specifications
- Other Name: Arm, Steering Knuckle Upper & Lower Control; Control Arm
- Position: Front Lower
- Replaces: 15594134, 12548332
- Item Weight: 31.10 Pounds
- Item Dimensions: 2.2 x 2.2 x 0.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15988034
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet K3500 Submodels:
- Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
2000 Chevrolet K3500 Upper Control Arm, Passenger Side
Part Number: 12543998
Product Specifications
- Other Name: Arm Kit, Steering Knuckle & Control Arm Assembly with Ball Joint.
- Position: Passenger Side
- Replaces: 15616866
- Item Weight: 9.90 Pounds
- Item Dimensions: 20.1 x 13.9 x 6.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12543998
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet K3500 Submodels:
- Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
2000 Chevrolet K3500 Upper Control Arm, Driver Side
Part Number: 12543997
Product Specifications
- Other Name: Arm Kit, Steering Knuckle & Control Arm Assembly with Ball Joint.
- Position: Driver Side
- Item Weight: 9.50 Pounds
- Item Dimensions: 16.9 x 16.7 x 7.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12543997
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet K3500 Submodels:
- Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
2000 Chevrolet K3500 Upper Control Arm, Driver Side
Part Number: 12388431
Product Specifications
- Other Name: Suspension Control Arm and Ball Joint Assembly; Control Arm Assembly; Arm Kit, Steering Knuckle Upper & Lower Control; Control Arm
- Position: Upper Driver Side
- Replaces: 15665186
- Item Weight: 9.40 Pounds
- Item Dimensions: 12.7 x 11.8 x 4.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12388431
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet K3500 Submodels:
- Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
2000 Chevrolet K3500 Upper Control Arm, Passenger Side
Part Number: 12388432
Product Specifications
- Other Name: Suspension Control Arm and Ball Joint Assembly; Control Arm Assembly; Arm Kit, Steering Knuckle Upper & Lower Control; Control Arm
- Position: Upper Passenger Side
- Replaces: 15665176, 15665187
- Item Weight: 9.60 Pounds
- Item Dimensions: 12.9 x 12.2 x 4.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12388432
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet K3500 Submodels:
- Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
2000 Chevrolet K3500 Lower Control Arm, Passenger Side
Part Number: 15006608
Product Specifications
- Other Name: Arm, Steering Knuckle Control Arm and Ball Joint Assembly; Suspension Control Arm Assembly.
- Position: Passenger Side
- Item Weight: 33.70 Pounds
- Item Dimensions: 20.7 x 21.3 x 4.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15006608
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet K3500 Submodels:
- Base, Cheyenne, LS, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
2000 Chevrolet K3500 Lower Control Arm, Driver Side
Part Number: 15006607
Product Specifications
- Other Name: Arm, Steering Knuckle Control Arm and Ball Joint Assembly; Suspension Control Arm Assembly.
- Position: Driver Side
- Item Weight: 34.20 Pounds
- Item Dimensions: 21.1 x 18.7 x 5.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15006607
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet K3500 Submodels:
- Base, Cheyenne, LS, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
2000 Chevrolet K3500 Upper Control Arm, Passenger Side
Part Number: 12544000
Product Specifications
- Other Name: Arm Kit, Steering Knuckle & Control Arm Assembly with Ball Joint.
- Position: Passenger Side
- Replaces: 15634918
- Item Weight: 9.40 Pounds
- Item Dimensions: 14.2 x 12.5 x 5.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12544000
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet K3500 Submodels:
- Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
2000 Chevrolet K3500 Upper Control Arm, Driver Side
Part Number: 12543999
Product Specifications
- Other Name: Arm Kit, Steering Knuckle & Control Arm Assembly with Ball Joint.
- Position: Driver Side
- Item Weight: 9.80 Pounds
- Item Dimensions: 14.6 x 12.4 x 4.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12543999
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet K3500 Submodels:
- Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS

2000 Chevrolet K3500 Control Arm

With a comprehensive array of OEM 2000 Chevrolet K3500 Control Arm, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2000 Chevrolet K3500 Control Arm are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2000 Chevrolet K3500 Control Arm Parts Questions & Experts Answers

Q: How to service and repair the front lower control arm on 2000 Chevrolet K3500?
A: The necessary equipment for serving and repairing the front lower Control Arm includes the following tools: steering linkage puller (J 24319-B), torsion bar loading/unloading tool (J 36202), ball joint separator (J 36607) and lower Control Arm Bushing service set (Series 30) (J 36618), ball joint c-clamp (J 9519-23). You need the steering linkage puller (J 24319-B) alongside torsion bar loading/unloading tool (J 36202) and Ball Joint separator (J 36607) and lower Control Arm Bushing service set (Series 30) (J 36618) and Ball Joint c-clamp (J 9519-23). The service starts with vehicle elevating and using safety stands for support. Unloading the torsion bar requires the j 36202 torsion bar loading/unloading tool while marking the adjuster bolt for later installation before the adjuster arm's removal. Start by removing the outer Axle Shaft nut and washer from the hub assembly then follow up by taking off the brake caliper and brake rotor. Extract the lower shock absorber bolt from the Control Arm when you compress the shock absorber with the shock absorber. First disconnect the inner Tie Rod End from the relay rod using the steering linkage puller (J 24319-B). Next use the jack to support the lower Control Arm before removing the stabilizer link. First disconnect the halfshaft assembly with its attached cotter pin and nut from the upper Ball Joint then use the Ball Joint separator (J 36607) to separate the upper Ball Joint from the knuckle. First you must remove the lower Control Arm nuts with their washers and their bolts before taking out the jointed combination of lower Control Arm and knuckle. Users need to unbend crimps of the front bushing before extracting it through lower Control Arm Bushing service set (J 36618). During repair replace the lower Control Arm when the bushings on k1 and k2 vehicles require replacement due to wear or damage. Installation requires using the lower Control Arm Bushing service set (J 36618) combined with Ball Joint c-clamp (J 9519-23) to install front and rear bushings through proper crimping. Install the lower Control Arm together with the knuckle assembly but tighten all nuts to 165 nm (121 ft. Lbs.) at the specified z height position of the Control Arm. The technician starts the drive axle through the hub before joining the Ball Joint to the knuckle followed by Ball Joint nut installation to 128 nm (94 ft. Lbs.) torque before adding the cotter pin. Use the torsion bar loading/unloading tool (J 36202) to load the bar initially then mount the adjuster arm before installing the final bolt. Flush installation begins with the halfshaft assembly followed by the lower shock absorber bolt and stabilizer link before adding tire and wheel assembly and vehicle lowering and front wheel alignment testing.