How to replace the front brake calipers on 2005 GMC Safari?

Beginning the front brake caliper replacement requires checking brake master cylinder fluid level; when it stands at the halfway mark you do not need to remove fluid but if it exceeds that position you should lower it to the middle setting. Lift and support the vehicle before taking out the tire and wheel setup. Press the brake caliper pistons down using a c-clamp tool to hold them against the back of the outside brake pad. Use this method until all pistons are fully compressed. Clean both sides of the brake hose end and put a rubber seal or plug over the open brake pipe section to keep brake fluid in the system. Take off the brake hose to caliper bolt while discarding 2 copper gaskets that may be stuck to brake components. After that detach the brake hose from the caliper. Take out the brake caliper bolts carefully and avoid pressuring the brake pedals when all brake parts are dismounted to keep components safe. Take the brake caliper off from its mounting base. Fasten the brake caliper to its mounting bracket first and later bolt on the 2 mounting bolts while tightening them to 108 nm (80 lb ft). Install the brake hose onto the caliper bolt and thread in new copper gaskets at the brake hose fitting. Secure the brake hose to the caliper bolt with its socket. The bolt brings 40 nm (30 lb ft) resistance pressure when tightened. Follow brake bleeding steps, then put back the tire and wheel parts before bringing the vehicle down. Also refill the braking system master cylinder with new fluid.

OEM 2005 GMC Safari Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Brake Calipers found

View related parts
2005 GMC Safari Caliper
Part Number: 19331021
$170.23 MSRP: $328.77
You Save: $158.54 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Rear
- Replaces: 18040101, 25848000
- Item Weight: 11.90 Pounds
- Item Dimensions: 7.2 x 4.1 x 12.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19331021
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2005 GMC Safari Submodels:
- Base, SLE, SLT | 6 Cyl 4.3 L GAS
View related parts
2005 GMC Safari Caliper
Part Number: 19331022
$171.88 MSRP: $331.97
You Save: $160.09 (49%)
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Rear
- Replaces: 25848001, 18040100
- Item Weight: 11.80 Pounds
- Item Dimensions: 13.0 x 7.1 x 4.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19331022
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2005 GMC Safari Submodels:
- Base, SLE, SLT | 6 Cyl 4.3 L GAS
View related parts
2005 GMC Safari Caliper, Driver Side
Part Number: 18040100
$171.88 MSRP: $331.97
You Save: $160.09 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Driver Side
- Replaced by: 19331022
- Item Weight: 11.80 Pounds
- Item Dimensions: 12.8 x 7.2 x 4.0 inches
- Condition: New
- SKU: 18040100
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2005 GMC Safari Submodels:
- Base, SLE, SLT | 6 Cyl 4.3 L GAS
View related parts
2005 GMC Safari Overhaul Kit, Rear
Part Number: 18040086
Product Specifications
- Other Name: Caliper Kit, Rear Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Overhaul Kit; Caliper Kit, Wheel Brake Cylinder/Caliper Piston; Caliper Kit, Wheel Cylinder Piston
- Position: Rear
- Item Weight: 0.50 Pounds
- Item Dimensions: 13.0 x 7.1 x 4.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 18040086
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2005 GMC Safari Submodels:
- Base, SLE, SLT | 6 Cyl 4.3 L GAS
View related parts
2005 GMC Safari Caliper, Passenger Side
Part Number: 18040088
Product Specifications
- Other Name: Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Passenger Side
- Item Weight: 4.10 Pounds
- Item Dimensions: 9.5 x 8.2 x 6.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18040088
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2005 GMC Safari Submodels:
- Base, SLE, SLT | 6 Cyl 4.3 L GAS
View related parts
2005 GMC Safari Caliper, Driver Side
Part Number: 18040087
Product Specifications
- Other Name: Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Driver Side
- Item Weight: 4.40 Pounds
- Item Dimensions: 9.3 x 8.5 x 6.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18040087
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2005 GMC Safari Submodels:
- Base, SLE, SLT | 6 Cyl 4.3 L GAS

2005 GMC Safari Brake Calipers

With a comprehensive array of OEM 2005 GMC Safari Brake Calipers, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2005 GMC Safari Brake Calipers are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2005 GMC Safari Brake Calipers Parts Questions & Experts Answers

Q: How to replace the front brake calipers on 2005 GMC Safari?
A: Beginning the front brake caliper replacement requires checking brake master cylinder fluid level; when it stands at the halfway mark you do not need to remove fluid but if it exceeds that position you should lower it to the middle setting. Lift and support the vehicle before taking out the tire and wheel setup. Press the brake caliper pistons down using a c-clamp tool to hold them against the back of the outside brake pad. Use this method until all pistons are fully compressed. Clean both sides of the brake hose end and put a rubber seal or plug over the open brake pipe section to keep brake fluid in the system. Take off the brake hose to caliper bolt while discarding 2 copper gaskets that may be stuck to brake components. After that detach the brake hose from the caliper. Take out the brake caliper bolts carefully and avoid pressuring the brake pedals when all brake parts are dismounted to keep components safe. Take the brake caliper off from its mounting base. Fasten the brake caliper to its mounting bracket first and later bolt on the 2 mounting bolts while tightening them to 108 nm (80 lb ft). Install the brake hose onto the caliper bolt and thread in new copper gaskets at the brake hose fitting. Secure the brake hose to the caliper bolt with its socket. The bolt brings 40 nm (30 lb ft) resistance pressure when tightened. Follow brake bleeding steps, then put back the tire and wheel parts before bringing the vehicle down. Also refill the braking system master cylinder with new fluid.