How to replace the control arm bushing on Cadillac Eldorado?

Vehicle maintenance begins with vehicle raising and support followed by tire removal along with wheel assembly and brake bracket retainers. Before changing the right side bushing users should detach both the shock tower bracket with the road sensing suspension position sensor while also lowering down their exhaust system and heat shield. Underneath the rear suspension support forward arm install a screw jack before taking out the forward arm nuts and bolts while watching for brake caliper, hose and pipe positions to prevent damage. Replace the Control Arm Bushing set (J21474-01) between forward arm flanges when the arm falls to its lowest position at 12.7 cm (5 inches). Apply high pressure lubricant on screw assembly (J21474-19) threads before installing the Control Arm Bushing set (J21474-01), bushing receiver (J21474-5), long nut (J21474-18) and screw assembly (J21474-19). Pull the bushing out of the forward arm through tight nut rotation. Place the new bushing on the forward arm where its flange notches match the 12 o'clock and 6 o'clock positions and install it with the outboard side looking in. Use the Control Arm Bushing set (J21474-01) one more time. Then add high pressure lubricant to the threads of the screw assembly (J21474-19). Place and tighten the Control Arm Bushing set (J21474-01), bushing receiver (J21474-5), long nut (J21474-18), and screw assembly (J21474-19) to push the bushing inside the forward arm until its flange settles into place. Before elevation first confirm the suspension insulator alignment looks correct before slowly lifting the support to match it with the body while repeating any brake modifications if required. The installation continues with forward arm bolts, nuts, and washers which secure the suspension support while right side nuts reach 63 nm (46 ft. Lbs.) and left side bolts attain 102 nm (75 ft. Lbs.) and upper mounting bolts require 102 nm (75 ft. Lbs.). On completion put the tire and wheel assemblies back on then lower the vehicle. Reinstall the exhaust system and heat shield and reconnect the road sensing suspension position sensor and bracket. Afterward install the brake bracket retainer screw.

OEM Cadillac Eldorado Control Arm Bushing

Suspension Arm Bushing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Control Arm Bushings found

View related parts
Cadillac Eldorado Bushing Insulator, White, Lower Part Number: 22530936
Product Specifications
- Other Name: Insulator, Steering Knuckle Lower Control Arm; Lower Control Arm Insulator; Insulator; Bushings
- Position: Lower
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1996 Cadillac Eldorado | Base, Biarritz, ETC, Sport, Spring Edition, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Eldorado Bushing Insulator, Blue, Lower Part Number: 22528801
Product Specifications
- Other Name: Insulator, Steering Knuckle Lower Control Arm; Control Arm Bushing; Axle Pivot Bushing; Lower Control Arm Front Bushing; Lower Control Arm Insulator; Insulator; Bushings
- Position: Lower
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1996 Cadillac Eldorado | Base, Biarritz, ETC, Sport, Spring Edition, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Eldorado Control Arm Bushing, Rear Part Number: 1627757
Product Specifications
- Other Name: Bushing, Rear Suspension Support; Axle Support; Crossmember; Pivot; Sway Bar; Beam Mount; Stabilizer Link Bushing; Insulator; Shaft; Support; Suspension Crossmember; Bar Insulator; Rear Axle Control Arm
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-2002 Cadillac Eldorado | Base, Biarritz, ESC, ETC, Sport, Spring Edition, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Eldorado Lower Control Arm Bushing Part Number: 3544718
Product Specifications
- Other Name: Bushing Assembly-Front Lower Control Arm; Control Arm Bushing; Axle Pivot Bushing; Lower Control Arm Rear Bushing; Lower Control Arm Washer; Bushing; Bushings; Bushing, Steering Knuckle Lower Control Arm
- Position: Lower
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1996 Cadillac Eldorado | Base, Biarritz, ETC, Sport, Spring Edition, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Eldorado Lower Control Arm Bushing, Green Part Number: 1629205
Product Specifications
- Other Name: Bush Assembly *Green; Suspension Control Arm Bushing; Axle Support Bushing; Control Arm Bushing; Axle Beam Mount; Lower Control Arm Outer Bushing; Bushings; Bushing, Rear Axle Control Arm
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1993 Cadillac Eldorado | Base, Biarritz, Sport, Spring Edition, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Eldorado Lower Control Arm Bushing, Blue Part Number: 1628807
Product Specifications
- Other Name: Bushing *Blue; Axle Support Bushing; Control Arm Bushing; Axle Beam Mount; Lower Control Arm Inner Bushing; Bushings; Bushing, Rear Axle Control Arm
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1993 Cadillac Eldorado | Base, Biarritz, Sport, Spring Edition, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Eldorado Lower Control Arm Front Bushing, Blue Part Number: 22528799
$14.57 MSRP: $22.83
You Save: $8.26 (37%)
Product Specifications
- Other Name: Insulator, Steering Knuckle Lower Control Arm; Control Arm Bushing; Axle Pivot Bushing; Lower Control Arm Insulator; Insulator; Bushings
- Position: Lower
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1996 Cadillac Eldorado | Base, Biarritz, ETC, Sport, Spring Edition, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS

Cadillac Eldorado Control Arm Bushing

Want to cut long-term maintenance and repair costs? Choose OEM Control Arm Bushing. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Cadillac Eldorado parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Cadillac Eldorado Control Arm Bushing includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Control Arm Bushing of Cadillac Eldorado cars is a connecting section of the cars secondary suspension system, where the control arms pivot. Sitting in between the control arm and the car body, these metal sleeves with an isolating layer help minimize the vibrations and wearing between the control arm, and the road as well as the steering inputs. Rubber, steel, aluminum, polyurethane, synthetic elastomer are some of the materials used in these bushings and each exhibits different degree of endurance and performance. In choosing the ordinary control arm bushings the material used would be appropriate to use since their main function would be as a replacement part.

Cadillac Eldorado Control Arm Bushing Parts and Q&A

Control Arm Bushing, Rear
1627757
Q: How to replace the control arm bushing on Cadillac Eldorado?
A:
Vehicle maintenance begins with vehicle raising and support followed by tire removal along with wheel assembly and brake bracket retainers. Before changing the right side bushing users should detach both the shock tower bracket with the road sensing suspension position sensor while also lowering down their exhaust system and heat shield. Underneath the rear suspension support forward arm install a screw jack before taking out the forward arm nuts and bolts while watching for brake caliper, hose and pipe positions to prevent damage. Replace the Control Arm Bushing set (J21474-01) between forward arm flanges when the arm falls to its lowest position at 12.7 cm (5 inches). Apply high pressure lubricant on screw assembly (J21474-19) threads before installing the Control Arm Bushing set (J21474-01), bushing receiver (J21474-5), long nut (J21474-18) and screw assembly (J21474-19). Pull the bushing out of the forward arm through tight nut rotation. Place the new bushing on the forward arm where its flange notches match the 12 o'clock and 6 o'clock positions and install it with the outboard side looking in. Use the Control Arm Bushing set (J21474-01) one more time. Then add high pressure lubricant to the threads of the screw assembly (J21474-19). Place and tighten the Control Arm Bushing set (J21474-01), bushing receiver (J21474-5), long nut (J21474-18), and screw assembly (J21474-19) to push the bushing inside the forward arm until its flange settles into place. Before elevation first confirm the suspension insulator alignment looks correct before slowly lifting the support to match it with the body while repeating any brake modifications if required. The installation continues with forward arm bolts, nuts, and washers which secure the suspension support while right side nuts reach 63 nm (46 ft. Lbs.) and left side bolts attain 102 nm (75 ft. Lbs.) and upper mounting bolts require 102 nm (75 ft. Lbs.). On completion put the tire and wheel assemblies back on then lower the vehicle. Reinstall the exhaust system and heat shield and reconnect the road sensing suspension position sensor and bracket. Afterward install the brake bracket retainer screw.