Make sure this part fits

GM 10328755
Nameplate, Silver, Front

2001-2002 GM

Customer Questions & Expert Answers (4)
GM 10328755 Nameplate, Silver, Front
  • Part Description
    Emblem, Front Side Door
  • Position
    Front
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2001-2002 Chevrolet VentureBase, LS, LT, Plus, Value, Warner Bros.6 Cyl 3.4 L GAS
    2001-2002 Oldsmobile SilhouettePremiere6 Cyl 3.4 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 10328755 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 10328755 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace or repair an emblem/nameplate on a door on Chevrolet Venture? Posted by Customer
    A:
    You need to secure the installation area with tape before placing alignment marks to put on or fix a door emblem/nameplate. Apply heat from the J 25070 heat gun over the emblem/nameplate in circular motions for 30 seconds while keeping the gun 152 mm away from the surface. You can take out the emblem/nameplate using a plastic tool and flat blade. Body parts need the 3M(TM) Scotch Brite molding adhesive remover disk (3M(TM) P/N 07501) while plastic parts should be cleaned with a lint-free cloth dipped in VMP naphtha or a 50/50 isopropyl alcohol-water mix. Use the same cloth with cleaning solution to wipe the prepared area afterward and dry it completely. Apply tape to indicate the spot when no marking already exists. Mount the LS emblem/nameplate properly while placing the MONTANA emblem/nameplate 33.35 mm (1.313 in) from top of the side molding down and 38.1 mm (1.50 in) from the door front edge to its front edge. Position the WB emblem/nameplate 5.512 inches above and 2.640 inches away from its specific installation point. Fix the PREMIERE emblem/nameplate at 41 mm (1.614 in) down from the top and 60 mm (2.362 in) across from the left edge. To install the MONTANA THUNDER emblem/nameplate position it with dimensions of 70mm x 195mm and 95mm. The ends should measure 30mm and 70mm respectively. You must heat the installation spot to 27-41°C using J 25070 (Heat Gun) until it reaches 80-105°F. Keep the emblem/nameplate surface at 29-32°C. Place the emblem/nameplate according to the reference marks and remove the protection film. Then press it firmly while ensuring proper surface contact all around. Dispel the protective backing from the surface where it will be attached.
    Posted by ChevyPartsGiant Specialist
    Q:
    How should the emblem/nameplate be heated for the 2002 Chevrolet Venture? Posted by Customer
    A:
    Use a J 25070 Heat Gun in a circular motion for about 30 seconds, holding it approximately 152 mm (6 in) from the surface.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    How should the area for installation be prepared for the 2001 Chevrolet Venture? Posted by Customer
    A:
    Clean it with the same cleaning solution and dry it thoroughly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Nameplate, Silver, Front 10328755 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 10328755 Nameplate, Silver, Front is available in the market under the name GM Emblem. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 10328755 Nameplate, Silver, Front fits certain Chevrolet Venture models, as well as Oldsmobile Silhouette models.
The original GM component designated by manufacturer part number 10328755 maintains top performance when functioning as the Emblem, Front Side Door unit at its Front. The component 10328755 is constructed from durable material and its dimensions span 8.4 x 2.1 x 0.4 inches while weighing 0.40 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. The part 10328755 has available replacement options. Each vehicle needs 2 units of the part marked as SKU 10328755. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.