Menu
×
Search Bar
Search by Part Number, Part Name, or Vehicle
My Garage
Cart
Help Center Contact Us
Make sure this part fits

GM 22711827
Axle Assembly, Front Driver Side

2002-2006 GM

Customer Questions & Expert Answers (3)
GM 22711827 Axle Assembly, Front Driver Side
  • Part Description
    Shaft Assembly-Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle
  • Position
    Front Driver Side
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers

  • 22711827 Axle Assembly, Front Driver Side is Ref No. 1 in the diagram below

    2003 Saturn Vue Axle Assembly, Front Driver Side Diagram for 22711827
    The diagram listed above is for your reference. View diagram for your vehicle

    Related Parts for 22711827

  • Product Specifications

    BrandGenuine GM
    Manufacturer Part Number22711827
    Part DescriptionShaft Assembly-Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle
    Other NamesAxle; Shaft, Front Wheel Drive Axle
    Item Dimensions7.4 x 6.2 x 35.0 inches
    Item Weight5.10 Pounds
    PositionFront Driver Side
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerGeneral Motors
    SKU22711827
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California's Proposition 65

  • Vehicle Fitment

    Year Make Model Trim Engine
    2005-2006 Chevrolet EquinoxLS, LT6 Cyl 3.4 L GAS
    2006 Pontiac TorrentBase6 Cyl 3.4 L GAS
    2002-2003 Saturn VueBase6 Cyl 3.0 L GAS

  • Customer Questions & Expert Answers

    Q:
    Can you help me check if this 22711827 is the right part for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 22711827 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the front wheel axle shaft on Chevrolet Equinox? Posted by Customer
    A:
    Start your front Axle Shaft replacement by lifting and supporting your vehicle then taking off both the wheel and tire. Procedure starts with removing the Axle Shaft Spindle Nut then checking for ball stud rotation until completing the outer Tie Rod End-to-steering knuckle nut removal. Start by using the steering linkage and tie rod puller (J 24319-B) to break the Tie Rod End from the Steering Knuckle then discard the lower ball joint stud's cotter pin. Finally remove the ball joint stud and its safety nut. Recover the Steering Knuckle from the lower ball joint stud using the ball joint separator (J 43828) before you uninstall the lower stabilizer bar link nut. A wood block and hammer may be needed for using to disengage the Axle Shaft spindle from the Wheel Hub assembly. To prevent fluid loss and start the Axle Shaft removal procedure use the rear wheel Axle Shaft removal tool (J 45341) with the slide hammer (J 2619-01) at the Axle Shaft inner tripot joint. Owners of all-wheel drive vehicles must also cap the power takeoff unit opening. The vehicle must be freed of its Axle Shaft. When installing the Axle Shaft first add a new retaining ring on the output shaft before using a seal protector (J 44394) for oil seal installation. Push the Axle Shaft tripot joint onto the output shaft until it reaches full seat seating. Before final assembly place the constant velocity joint spindle into the Wheel Hub/bearing assembly then hand install a new Axle Shaft Spindle Nut followed by installation of the lower ball joint stud to the Steering Knuckle using a torque wrench set to 10 nm (89 inch lbs.) initial then added torque of 150 degrees. Use a back up wrench to tighten the stabilizer bar link stud nut up to 65 nm (48 ft. Lbs.). Afterward, position the lower link onto the stabilizer bar and install the cotter pin to the ball joint stud. The Steering Knuckle receives the Tie Rod End and you must use the steering linkage installer (J 44015) to pull the stud into position before tightening it to 40 nm (30 ft. Lbs.). Apply a new nut to the Tie Rod End stud and use torque to 50 nm (37 ft. Lbs.). Complete your service by tightening the Axle Shaft Spindle Nut to 205 nm (151 ft. Lbs.), attaching the tire and wheel assembly and checking the vehicle height before verifying the transmission fluid level sufficiency.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the torque specification for the lower control arm-to-suspension knuckle bolt and nut for the 2006 Chevrolet Equinox? Posted by Customer
    A:
    Tighten them to 160 Nm (118 ft. lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Axle Shaft
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM 22711827, Excellent Performance and Perfect Fitment

To ensure reliability, purchase GM part # 22711827 Axle Assembly, Front Driver Side. It is sometimes referred to as GM Axle Shaft. Choosing OEM parts is the optimal decision for guaranteeing superior quality and perfect performance. These components undergo stringent quality checks and are carefully constructed to comply with GM's factory specifications, ensuring a smooth installation process.

ChevyPartsGiant.com is a leading supplier of genuine GM parts such as GM 22711827 Axle Assembly, Front Driver Side. Our website boasts an extensive inventory of OEM GM parts, available at highly competitive prices in the market. Should you require any new genuine GM parts, rest assured we will deliver them swiftly and efficiently to your doorstep. Furthermore, all our parts come with the assurance of a manufacturer's warranty. For detailed Chevy parts information, click here.
Choose ChevyPartsGiant for discounted prices, exceptional service and fast delivery