Make sure this part fits

GM 10334040
Nameplate, Rear

2004-2011 GM

Customer Questions & Expert Answers (20)
GM 10334040 Nameplate, Rear
  • Part Description
    Plate, Rear End Panel And Tailgate
  • Position
    Rear
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2006-2011 Cadillac DTSBase, Livery, Luxury, Platinum, Premium8 Cyl 4.6 L GAS
    2004-2005 Cadillac DeVilleBase, DHS, DTS, Protection Series8 Cyl 4.6 L GAS
    2004-2009 Cadillac SRXBase8 Cyl 4.6 L GAS
    2005-2010 Cadillac STSBase, Platinum8 Cyl 4.6 L GAS
    2004 Cadillac SevilleSLS8 Cyl 4.6 L GAS
    2004-2008 Cadillac XLRBase, Platinum, V8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 10334040 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 10334040 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How do you install the new emblem for the 2008 Cadillac SRX? Posted by Customer
    A:
    Peel the backing from the adhesive tape, align the pins on the backside of the emblem with the holes in the grille, and firmly press the emblem into place for 30 seconds to ensure proper adhesion.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What should be used for adhesive removal for the 2005 Cadillac SRX? Posted by Customer
    A:
    A 3M(TM) Scotch Brite molding adhesive remover disk (3M(TM) P/N 07502) for body panels, or a lint-free cloth with Varnish Makers and Painters (VMP) naphtha or a 50/50 mixture of isopropyl alcohol and water for plastic panels.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What preparation is needed before installing the new emblem for the 2004 Cadillac SRX? Posted by Customer
    A:
    Wipe the area with a clean lint-free cloth using a 50/50 mixture of isopropyl alcohol and water.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    How do you remove the emblem/nameplate for the 2009 Cadillac SRX? Posted by Customer
    A:
    Carefully remove it with a small plastic flat-bladed tool to avoid damaging the paint.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What should be done to ensure all adhesive is removed when replacing the emblem/nameplate for the 2004 Cadillac Seville? Posted by Customer
    A:
    For body panels, utilize a 3M(TM) Scotch Brite molding adhesive remover disk or an equivalent, and for plastic panels, use a lint-free cloth with Varnish Makers and Painters naphtha or a 50/50 mixture of isopropyl alcohol and water.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What is the first step to replace the Radiator Grille Emblem for the 2007 Cadillac SRX? Posted by Customer
    A:
    Use the Heat Gun (J 25070) to heat the loose emblem, holding it approximately 152 mm (6 in) from the emblem surface and applying heat in a circular motion until the emblem can be pulled from the grille.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What should be done if the location is not marked for the 2005 Cadillac STS? Posted by Customer
    A:
    Apply tape to indicate where the emblem/nameplate will go.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What should be avoided when handling the emblem/nameplate for the 2007 Cadillac XLR? Posted by Customer
    A:
    Avoid touching the adhesive backing.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What should be avoided when handling the emblem/nameplate for the 2006 Cadillac XLR? Posted by Customer
    A:
    Avoid touching the adhesive backing.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What tool should be used to remove the emblem/nameplate for the 2004 Cadillac XLR? Posted by Customer
    A:
    Carefully use a plastic, flat-bladed tool to remove the emblem/nameplate from the panel surface.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    How should the emblem/nameplate be heated for the 2008 Cadillac XLR? Posted by Customer
    A:
    Use a J 25070 (Heat Gun) in a circular motion for about 30 seconds, holding it approximately 152 mm (6 in) from the surface.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What tools are needed to replace the liftgate emblem and nameplate for the 2007 Cadillac SRX? Posted by Customer
    A:
    Heat Gun (J 25070).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    How should the emblem/nameplate be heated for the 2007 Cadillac STS? Posted by Customer
    A:
    Use a J 25070 Heat Gun in a circular motion for about 30 seconds, holding it approximately 152 mm (6 in) from the surface.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What should be done if the location is unmarked for the 2008 Cadillac STS? Posted by Customer
    A:
    Apply tape and mark it.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    Where should the V8 Northstar emblem be positioned for the 2007 Cadillac XLR? Posted by Customer
    A:
    On the driver side, 67 mm (2.6 in) from the left edge and 86 mm (3.4 in) from the bottom edge of the rear compartment lid.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What should be done if the location for the emblem/nameplate is not marked for the 2009 Cadillac STS? Posted by Customer
    A:
    Apply tape to indicate where the emblem/nameplate will go.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What temperature should the emblem/nameplate be before installation for the 2010 Cadillac STS? Posted by Customer
    A:
    Ensure the emblem/nameplate is around 29-32°C (85-90°F).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What tools are needed to replace the emblem/nameplate on the liftgate for the 2006 Cadillac SRX? Posted by Customer
    A:
    Heat Gun (J 25070), 3M(TM) Scotch Brite molding adhesive remover disk (3M(TM) P/N 07502) or an equivalent, a lint-free cloth, and Varnish Makers and Painters (VMP) naphtha or a 50/50 mixture of isopropyl alcohol and water.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What tool should be used to remove the emblem/nameplate for the 2005 Cadillac XLR? Posted by Customer
    A:
    Carefully use a plastic, flat-bladed tool to remove the emblem/nameplate from the panel surface.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Nameplate, Rear 10334040 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 10334040 Nameplate, Rear is available in the market under the name GM Emblem. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 10334040 Nameplate, Rear fits certain Cadillac XLR, SRX, DTS models.
The original GM component designated by manufacturer part number 10334040 maintains top performance when functioning as the Plate, Rear End Panel And Tailgate unit at its Rear. The component 10334040 is constructed from durable material and its dimensions span 5.3 x 1.3 x 0.3 inches while weighing 0.30 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Plate,Rear End Panel And Tailgate. The part 10334040 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.