Make sure this part fits

GM 10315827
Lock Switch, Driver Side

2004-2009 Cadillac XLR

Customer Questions & Expert Answers (7)
GM 10315827 Lock Switch, Driver Side
  • Part Description
    Switch, Door Electric And Vacuum Locks; Door Lock Switch
  • Position
    Driver Side
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine GM
    Manufacturer Part Number10315827
    Part DescriptionSwitch, Door Electric And Vacuum Locks; Door Lock Switch
    Item Dimensions2.2 x 1.8 x 1.2 inches
    Item Weight0.50 Pounds
    PositionDriver Side
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerGeneral Motors
    SKU10315827
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California's Proposition 65
  • Vehicle Fitment

    Year Make Model Trim Engine
    2004-2009 Cadillac XLRBase, Platinum, V8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
  • Customer Questions & Expert Answers

    Q:
    Is this 10315827 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 10315827 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the power door lock switch in the driver door on Cadillac XLR? Posted by Customer
    A:
    The replacement of the power Door Lock Switch in the driver door needs the Ignition Switch to be in off before you begin by removing the door trim panel. Start by removing the retainer screws from the upper trim panel at its back section followed by taking off the upper trim from the door. Begin by taking out the inner energy absorber from the door panel followed by removing four retaining screws from the armrest rear section and one screw from its forward side. After disconnecting the wire harness from the armrest you should remove the assembly while protecting the finish with duct tape before removing the Power Window Switch assembly. Take out the power Door Lock Switch assembly from the pocket inside the door trim panel before disconnecting the wire harness. The new power Door Lock Switch installation requires a connection between wire harnesses at the Door Lock Switch assembly while securing it to the armrest switch plate aplique. Install the lock switch assembly into its pocket of the door trim panel after unwinding any protective tape and connect the wire harness to the Door Armrest assembly. Mount the armrest to the door trim panel by using 4 rear retaining screws along with one forward screw at the end and tighten them to 10 n.m (89 lb in). The technician should put back the inner energy absorber and the upper trim while tightening rear retaining screws to 10 n.m (89 lb in) before installing the door trim panel.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be done to protect the finish of the mirror, window, and applique for the 2009 Cadillac XLR? Posted by Customer
    A:
    Use duct tape to cover them.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Switch
    Q:
    What should be done after removing the inner energy absorber for the 2006 Cadillac XLR? Posted by Customer
    A:
    Remove the four retaining screws from the rear of the armrest and one retaining screw from the forward end of the armrest assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Switch
    Q:
    What should be installed after securing the armrest for the 2008 Cadillac XLR? Posted by Customer
    A:
    Install the inner energy absorber to the door panel.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Switch
    Q:
    How do you remove the armrest assembly for the 2005 Cadillac XLR? Posted by Customer
    A:
    Disconnect the armrest wire harness and take out the armrest assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Switch
    Q:
    What screws need to be removed next for the 2007 Cadillac XLR? Posted by Customer
    A:
    Remove the 4 retaining screws from the rear of the armrest and 1 retaining screw from the forward end of the armrest assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Switch
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM 10315827, Excellent Performance and Perfect Fitment

To ensure reliability, purchase GM part # 10315827 Lock Switch, Driver Side. It is sometimes referred to as GM Door Lock Switch. Choosing OEM parts is the optimal decision for guaranteeing superior quality and perfect performance. These components undergo stringent quality checks and are carefully constructed to comply with GM's factory specifications, ensuring a smooth installation process.

ChevyPartsGiant.com is a leading supplier of genuine GM parts such as GM 10315827 Lock Switch, Driver Side. Our website boasts an extensive inventory of OEM GM parts, available at highly competitive prices in the market. Should you require any new genuine GM parts, rest assured we will deliver them swiftly and efficiently to your doorstep. Furthermore, all our parts come with the assurance of a manufacturer's warranty. For detailed Cadillac parts information, click here.
Choose ChevyPartsGiant for discounted prices, exceptional service and fast delivery