ChevyParts
My Garage
My Account
Cart
OEM 2007 GMC Canyon Cam Gear
Camshaft Gear- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
3 Cam Gears found
2007 GMC Canyon Camshaft Gear Part Number: 24100362
$46.75 MSRP: $112.72You Save: $65.97 (59%)Product Specifications- Other Name: Sprocket, Camshaft; Variable Valve Timing Sprocket; Cam Gear; Sprocket; Sprocket, Engine Camshaft
- Item Weight: 1.40 Pounds
- Item Dimensions: 8.1 x 7.4 x 3.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 24100362
- Warranty: This genuine part is guaranteed by GM's factory warranty.
2007 GMC Canyon Actuator Assembly Part Number: 12575415
Product Specifications- Other Name: Actuator, Camshaft Position; Actuator; Actuator, Engine Camshaft
- Item Weight: 3.30 Pounds
- Item Dimensions: 7.3 x 6.3 x 4.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12575415
- Warranty: This genuine part is guaranteed by GM's factory warranty.
2007 GMC Canyon Actuator Assembly Part Number: 12581247
$144.66 MSRP: $227.61You Save: $82.95 (37%)Product Specifications- Other Name: Actuator, Engine Camshaft; Actuator
- Item Weight: 3.20 Pounds
- Item Dimensions: 8.2 x 7.3 x 3.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12581247
- Warranty: This genuine part is guaranteed by GM's factory warranty.
2007 GMC Canyon Cam Gear
With a comprehensive array of OEM 2007 GMC Canyon Cam Gear, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2007 GMC Canyon Cam Gear are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.
2007 GMC Canyon Cam Gear Parts and Q&A
- Q: How to replace the cam gear on the intake side on 2007 GMC Canyon?A: The procedure to replace the camshaft intake sprocket begins by removing the camshaft cover then rotating the Crankshaft clockwise until the #1 Piston arrives at top dead center (TDC) compression phase with the word delphi on the exhaust camshaft position actuator directed parallel to the Cylinder Head to cam cover mating surface. The timing mark on the intake camshaft sprocket establishes a guide for marking the adjacent section of Timing Chain. Position the camshaft holding tool (J 44221) at the rear of the camshafts before using the Timing Chain retention tool (J 44217) along with the chain holding tool (J-44217-45) to secure Timing Chain links near both engine sides by tightening wingnuts for stable gage blocks placement on the head edge. Start by removing and discarding the intake camshaft sprocket bolt before departing with the intake camshaft sprocket. To install properly position the marked Timing Chain link with the intake camshaft sprocket timing mark. Then use a 25 mm wrench on the camshaft hex and ensure the alignment pin snaps into place. Use the angle meter (J 45059) to tighten the new intake camshaft sprocket bolt until it reaches 20 n.m (15 lb ft) and an additional 100 degrees. Finish the procedure by taking out both timing tools named Timing Chain retention tool (J 44217) and chain holding tool (J-44217-45). Remove the camshaft holding tool (J 44221) then install the camshaft cover.
Related 2007 GMC Canyon Parts
2007 GMC Canyon Timing Chain
2007 GMC Canyon Balance Shaft Bearing Set
2007 GMC Canyon Camshaft
2007 GMC Canyon Camshaft Bearing
2007 GMC Canyon Head Gasket
2007 GMC Canyon Lash Adjuster
2007 GMC Canyon Motor And Transmission Mount
2007 GMC Canyon Oil Filler Cap
2007 GMC Canyon Oil Pan Gasket
2007 GMC Canyon Rocker Shaft Spring Kit
2007 GMC Canyon Rod Bearing
2007 GMC Canyon Timing Chain Guide