How to replace the inner CV Boot and CV Joint on Chevrolet K3500?

Start by collecting snap ring pliers (J8059) along with seal clamp tool (J35910) and split plate swage clamp for k10 models (J36652-98) and split plate swage clamp for k20/k30 models (J36652-1). You need four tools for this repair: snap ring pliers (J8059), seal clamp tool (J35910), split plate swage clamp for k10 models (J36652-98), and split plate swage clamp for k20/k30 models (J36652-1). Check the transmission sealing surface of the halfshaft for corrosion before cleaning it with 320 grit cloth if needed. A hand grinder should cut through the swage ring in order to remove the tripot housing without damaging it. After removing the housing completely degrease it thoroughly. When handling the tripot spider assembly maintain careful movements because separation of tripot balls and needle rollers will occur. After removing the boot clamp with side cutters evacuate the spider spacer ring by using snap ring pliers (J8059). Clear the halfshaft bar by cleaning it with a wire brush after removing the spacer ring , spider assembly , and tripot boot . All components must undergo examination for damage and wear before replacing them with new parts. To install the new small boot clamp on the joint boot use the seal clamp tool (J35910) at 136 nm (100 ft. Lbs.) torque. Position the convolute retainer properly across the inboard joint boot before installing the tripot spider assembly and spacer ring onto the halfshaft bar. Begin by filling the tripot housing and boot with grease supplied for packing. After reassembly ensure the swage ring achieves correct alignment. Place mount the split plate swage clamp (J36652) into a vise position and install your model-specific clamp before verifying the inboard stroke position. Apply torque to the clamp bolts while alternating each bolt until fastened, afterward remove both the boot's convolute retainer and halfshaft assembly.

OEM Chevrolet K3500 CV Boot

Axle Boot

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 CV Boots found

View related parts
Chevrolet K3500 Inner Boot, Front Part Number: 26062618
$33.23 MSRP: $54.75
You Save: $21.52 (40%)
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Outer Boot; Boot Kit, Front Axle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2000 Chevrolet K3500 | Base, Cheyenne, LS, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
Chevrolet K3500 Outer Boot, Front Part Number: 15868188
$65.70 MSRP: $111.85
You Save: $46.15 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Axle; CV Boot; Inner Boot
- Position: Front
- Replaces: 26062619
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2000 Chevrolet K3500 | Base, Cheyenne, LS, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
Chevrolet K3500 Outer Boot, Front Part Number: 26037370
Product Specifications
- Other Name: Boot Kit, Front Axle; CV Boot
- Position: Front
- Replaces: 26032807
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-2000 Chevrolet K3500 | Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
Chevrolet K3500 Inner Boot, Front Part Number: 26062615
$27.79 MSRP: $43.53
You Save: $15.74 (37%)
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Boot Kit, Front Axle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2000 Chevrolet K3500 | Base, Cheyenne, LS, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
Chevrolet K3500 Inner Boot, Front Part Number: 26055394
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Boot Kit, Front Axle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1997 Chevrolet K3500 | Base, Cheyenne, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
Chevrolet K3500 Outer Boot, Front Part Number: 26037155
Product Specifications
- Other Name: Boot Kit, Front Axle; CV Boot
- Position: Front
- Replaces: 26020729
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1997 Chevrolet K3500 | Base, Cheyenne, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
Chevrolet K3500 Inner Boot, Front Part Number: 26036985
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Boot Kit, Front Axle
- Position: Front
- Replaces: 07849566, 7849566, 26018970
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1994 Chevrolet K3500 | Base, Cheyenne, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS

Chevrolet K3500 CV Boot

Want to cut long-term maintenance and repair costs? Choose OEM CV Boot. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet K3500 parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet K3500 CV Boot includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Such part as Chevrolet K3500 CV Boot is the crucial factor that proves the dependability and the power of Chevrolet K3500 series trucks built between 1988 and 2002. This part or component, which is made out of either rubber or plastic material, is called a CV Boot and it performs the important function of shields for constant velocity or CV joints that are needed for the power distribution between the transaxle and the wheels. Through retaining the requisite lubricant and denying the accumulation of dirt and other unwanted particles within the Chevrolet K3500 CV Boot, the CV joints are made to work to the optimal of their capabilities and lives without difficulties. As suggested, compatibility with Rzeppa, tripod and double offset joints of K3500 models is exemplary of the units' versatility. It is essential to inspect the CV Boot frequently: even if there are crack or tear in CV Boot can cause CV joint failure, which underline this part's importance to the vehicle's performance and security. This CV Boot brings a lot of advantages the Chevrolet K3500, thanks to the vehicle's piled construction and its powerful Vortec engines. Chevrolet K3500 CV Boot has several features that make it stand out in the market and they include; The boot is designed to take extreme angles and work in harmony with changes in shaft length as experienced from suspension movement. In conclusion, the Chevrolet K3500 CV Boot is the exhibition of Chevrolet's quality work and continues to guarantee a well-equipped K3500 for both functions- commercial and recreational.

Chevrolet K3500 CV Boot Parts Questions & Experts Answers

Inner Boot, Front
26062615
Q: How to replace the inner CV Boot and CV Joint on Chevrolet K3500?
A:
Start by collecting snap ring pliers (J8059) along with seal clamp tool (J35910) and split plate swage clamp for k10 models (J36652-98) and split plate swage clamp for k20/k30 models (J36652-1). You need four tools for this repair: snap ring pliers (J8059), seal clamp tool (J35910), split plate swage clamp for k10 models (J36652-98), and split plate swage clamp for k20/k30 models (J36652-1). Check the transmission sealing surface of the halfshaft for corrosion before cleaning it with 320 grit cloth if needed. A hand grinder should cut through the swage ring in order to remove the tripot housing without damaging it. After removing the housing completely degrease it thoroughly. When handling the tripot spider assembly maintain careful movements because separation of tripot balls and needle rollers will occur. After removing the boot clamp with side cutters evacuate the spider spacer ring by using snap ring pliers (J8059). Clear the halfshaft bar by cleaning it with a wire brush after removing the spacer ring , spider assembly , and tripot boot . All components must undergo examination for damage and wear before replacing them with new parts. To install the new small boot clamp on the joint boot use the seal clamp tool (J35910) at 136 nm (100 ft. Lbs.) torque. Position the convolute retainer properly across the inboard joint boot before installing the tripot spider assembly and spacer ring onto the halfshaft bar. Begin by filling the tripot housing and boot with grease supplied for packing. After reassembly ensure the swage ring achieves correct alignment. Place mount the split plate swage clamp (J36652) into a vise position and install your model-specific clamp before verifying the inboard stroke position. Apply torque to the clamp bolts while alternating each bolt until fastened, afterward remove both the boot's convolute retainer and halfshaft assembly.