How to service and repair the pitman arm on GMC C2500?

First, lift the vehicle and make sure it is supported by jack stands to work on the Pitman Arm. Use the right tool to remove the ball joints. Clean the relay rod nut off the Pitman Arm ball stud and never reattach it for use again. Remove the relay rod from the Pitman Arm ball stud by following the (J 24319-01). Next, detach the nut on the Pitman Arm (8) and discard the washer since it is not necessary to use it again. Properly place the Pitman Arm (2) and shaft by aligning them and never try to drive or hammer them during assembly. With the use of the tool (J 29107-A), lift the Pitman Arm, inspect the ball stud for damage and test the seals on it. Install the Pitman Arm by putting it on the pitman shaft and align its marks with the marks on the shaft. Fit in the Pitman Arm washer and nut (8), then tighten them to 250 nm (184 ft. Lbs.). Apply the relay rod (9) to the Pitman Arm ball stud and check that the seal is present. Put in the (J 29193) and tighten to 62 nm (46 ft. Lbs.) to press the tapers until they are in place and afterwards, remove the (J 29193). In the end, replace the torque nut and tighten it to 62 nm (46 ft. Lbs.), after which you should lower the car.

OEM GMC C2500 Pitman Arm

Steering Pitman Arm

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Pitman Arms found

View related parts
GMC C2500 Pitman Arm Part Number: 26033290
$160.23 MSRP: $252.11
You Save: $91.88 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm Kit, Pitman; Steering Pitman Arm; Idler Arm; Arm Kit, Steering Pitman
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2000 GMC C2500 | Sierra SL, Sierra SLE, Sierra SLT | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Idler Arm Part Number: 19461033
$91.91 MSRP: $164.12
You Save: $72.21 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm Assembly, Steering Linkage Idler
- Replaces: 14002551, 88911335
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984 GMC C2500 | Base | 6 Cyl 4.1 L GAS, 6 Cyl 4.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Pitman Arm Part Number: 26051896
$103.77 MSRP: $142.06
You Save: $38.29 (27%)
ADD TO CART
Product Specifications
- Other Name: Arm Kit, Pitman; Steering Pitman Arm; Idler Arm; Arm Kit, Steering Pitman; Arm, Steering Pitman
- Replaces: 26032996
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-2000 GMC C2500 | Sierra, Sierra SL, Sierra SLE, Sierra SLT, Sierra SLX | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Pitman Arm Part Number: 26002889
Product Specifications
- Other Name: Arm Kit, Pitman; Idler Arm; Arm Kit, Steering Pitman
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1989 GMC C2500 | Sierra, Sierra SLE, Sierra SLX | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL
View related parts
GMC C2500 Sector Shaft Part Number: 7843970
Product Specifications
- Other Name: Gear; Pivot Shaft; Pitman Shaft; Shaft; Shaft, Steering Gear Pitman Shaft; Gear, Steering Gear Pitman Shaft
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1989 GMC C2500 | Sierra, Sierra SLE, Sierra SLX | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL
View related parts
GMC C2500 Sector Shaft Part Number: 7812834
Product Specifications
- Other Name: Shaft Assembly, Steering Gear Pitman (W/ Gear); Pitman Shaft; Pitman Gear; Shaft, Steering Gear Pitman Shaft; Gear, Steering Gear Pitman Shaft
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988, 1984-1986 GMC C2500 | Base, High Sierra, Sierra, Sierra Classic, Sierra SLE, Sierra SLX | 6 Cyl 4.1 L GAS, 6 Cyl 4.3 L GAS, 6 Cyl 4.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Idler Arm Part Number: 26059504
Product Specifications
- Other Name: Arm Kit, Steering Linkage Idler; Pitman Arm; Arm Kit, Steering Idler
- Replaces: 14067696
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988, 1984-1986 GMC C2500 | Base, High Sierra, Sierra, Sierra Classic, Sierra SLE, Sierra SLX | 6 Cyl 4.1 L GAS, 6 Cyl 4.3 L GAS, 6 Cyl 4.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Idler Arm Part Number: 26059030
Product Specifications
- Other Name: Arm Kit, Steering Linkage Idler; Steering Idler Arm; Pitman Arm; Idler Arm Assembly; Arm Kit, Steering Idler
- Replaces: 26028525
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-2000 GMC C2500 | Sierra, Sierra SL, Sierra SLE, Sierra SLT, Sierra SLX | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Idler Arm Part Number: 26016461
Product Specifications
- Other Name: Arm Kit, Steering Linkage Idler; Steering Idler Arm; Pitman Arm; Idler Arm Assembly; Arm Kit, Steering Idler
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1992 GMC C2500 | Sierra, Sierra SLE, Sierra SLX | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Pitman Arm Part Number: 14064660
Product Specifications
- Other Name: Arm, Pitman; Idler Arm; Arm, Steering Pitman
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1986 GMC C2500 | Base, High Sierra, Sierra Classic | 6 Cyl 4.1 L GAS, 6 Cyl 4.3 L GAS, 6 Cyl 4.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Pitman Arm Part Number: 14013039
Product Specifications
- Other Name: Arm, Steering Pitman; Steering Pitman Arm; Idler Arm; Arm Assembly, Steering Pitman
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988, 1984-1986 GMC C2500 | Base, High Sierra, Sierra, Sierra Classic, Sierra SLE, Sierra SLX | 6 Cyl 4.1 L GAS, 6 Cyl 4.3 L GAS, 6 Cyl 4.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Pitman Arm Part Number: 14013038
Product Specifications
- Other Name: Arm Assembly, Steering Pitman; Steering Pitman Arm; Idler Arm; Arm, Steering Pitman
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1986 GMC C2500 | Base, High Sierra, Sierra Classic | 6 Cyl 4.1 L GAS, 6 Cyl 4.3 L GAS, 6 Cyl 4.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 7.4 L GAS

GMC C2500 Pitman Arm

Want to cut long-term maintenance and repair costs? Choose OEM Pitman Arm. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine GMC C2500 parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM GMC C2500 Pitman Arm includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

This is a Pitman Arm that goes specifically to GMC C2500 boosting their reliability and performances according to user and expert opinions. This critical part resembles the link with the steering box and takes the drag link as the vital conduit for transforming rotational movement into linear, which is crucial for successful steering. This Pitman Arm is very reliable as it is made to cater the C2500 which can be used on different models of GMC C2500 produced from 1960 up to 1998 especially in heavy usage applications. This aspect makes it possible to bear the one-ton load capacity requirement thereby boosting the efficiency and safety of the GMC C2500. In other words, a well-functioning Pitman Arm helps to reduce the nutation and this is very essential for provide control on the road. GMC C2500 Pitman Arm can be considered as one of the leader in the automotive industry because it provides the stable work and can be used in the Base, Deluxe, Custom, Sierra, and Sierra Grande trims. Furthermore, with different models that have progressed from early wooden structures to high steel ones with ball joints and bearings, the Pitman Arm has a progress imploring aspect in automotive engineering. Providing proper steering and improving vehicle control, GMC C2500 Pitman Arm holds one of the essential functions for an excellent operation of the GMC C2500 as a durable and potent full-size pickup truck.

GMC C2500 Pitman Arm Parts Questions & Experts Answers

Pitman Arm
26033290
Q: How to service and repair the pitman arm on GMC C2500?
A:
First, lift the vehicle and make sure it is supported by jack stands to work on the Pitman Arm. Use the right tool to remove the Ball Joints. Clean the relay rod nut off the Pitman Arm ball stud and never reattach it for use again. Remove the relay rod from the Pitman Arm ball stud by following the (J 24319-01). Next, detach the nut on the Pitman Arm (8) and discard the washer since it is not necessary to use it again. Properly place the Pitman Arm (2) and shaft by aligning them and never try to drive or hammer them during assembly. With the use of the tool (J 29107-A), lift the Pitman Arm, inspect the ball stud for damage and test the seals on it. Install the Pitman Arm by putting it on the pitman shaft and align its marks with the marks on the shaft. Fit in the Pitman Arm washer and nut (8), then tighten them to 250 nm (184 ft. Lbs.). Apply the relay rod (9) to the Pitman Arm ball stud and check that the seal is present. Put in the (J 29193) and tighten to 62 nm (46 ft. Lbs.) to press the tapers until they are in place and afterwards, remove the (J 29193). In the end, replace the torque nut and tighten it to 62 nm (46 ft. Lbs.), after which you should lower the car.