Make sure this part fits

GM 19207384
Emblem

1997-2004 Chevrolet Corvette

Customer Questions & Expert Answers (7)
GM 19207384 Emblem
GM 19207384 Emblem
  • Part Description
    Emblem, Bumper/Fascia
  • Position
    Front
  • Replaces
    10258164
  • Manufacturer
    General Motors
Make sure this part fits
$133.78 MSRP: $200.01
You Save: $66.23 (34%)
Ships in 1-3 Business Days
1
ADD TO CART
  • Vehicle Fitment

    Year Make Model Trim Engine
    2004, 1997-2002 Chevrolet CorvetteBase, Indianapolis 500 Pace Car, Z068 Cyl 5.7 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 19207384 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 19207384 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the emblem/nameplate on the front fender on Chevrolet Corvette? Posted by Customer
    A:
    Before placing the new fender emblem you need to cover and tape the mounting area then use additional tape for precise placement. Apply the Heat Gun (J 25070) 152 mm (6 in) from the surface to heat the emblem/nameplate for 30 seconds while moving in a circular pattern. Avoid damage when you take off the panel surface emblem/nameplate with a plastic flat-tip tool. Before placing the component ensure to wipe clean the target area with a lint-free cloth followed by VMP naphtha or a 50/50 mix of isopropyl alcohol and water. Afterwards dry the surface thoroughly. When tagging the parts install the ZO6 emblem/nameplate as follows: place one end 216.5 mm (8.50 in) from the fender top, align the other end 212.74 mm (8.40 in) from the top and set the back 158.51 mm 6.24 in) from the rear fender edge. Heat the logo area with the Heat Gun (J25070) until it reaches 27-41°C (80-105°F) while keeping the emblem/nameplate near 29-32°C (85-90°F). Press the emblem/nameplate against the mounting area and peel off the protective liner from its back side without touching the sticky surface. Line up the part according to the reference points then push the item securely to the mount area with balanced force. Take off the protective tape from where the emblem will go.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace an emblem/nameplate on the front fender on Chevrolet Corvette? Posted by Customer
    A:
    Apply tape to shield the mounting area of the front fender before installing a new emblem/nameplate and place more tape as reference marks for orientation. Apply warm air from a Heat Gun (J 25070) over the emblem/nameplate for 30 seconds while moving the gun at a 152 mm (6 in) distance in circular patterns. Apply a plastic tool gently to take out the emblem/nameplate from its panel spot. Before adding the part use lint-free cloth and VMP naphtha or water-isopropyl alcohol mixture to clean the area. Let it dry completely before installation. Place tape first then mount the ZO6 device based on its dimensional requirements at 8.50 inches from top to bottom and 8.40 inches from top to bottom with a 6.24 inch depth from back to front when the dealer does not mark the locations. This specific emblem/nameplate for the 50th Anniversary has 162 mm (6.375 in) distance from the top edge to the top surface. Heat the install area to 27-41°C (80-105°F) using the Heat Gun (J 25070) while keeping the emblem/nameplate near 29-32°C (85-90°F). Install the emblem by placing it precisely against the marks after pulling off the liner from its adhesive backing then press it down on the surface using equal pressure to achieve good adherence. Take away the foil covering from the surface where you will install it.
    Posted by ChevyPartsGiant Specialist
    Q:
    How should the emblem/nameplate be heated for removal for the 2001 Chevrolet Corvette? Posted by Customer
    A:
    Heat the emblem/nameplate with a heat gun in a circular motion for about 30 seconds.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    How should the emblem/nameplate be heated for the 2002 Chevrolet Corvette? Posted by Customer
    A:
    Use a Heat Gun (J 25070) in a circular motion for about 30 seconds, holding it approximately 152 mm (6 in) from the surface.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What is the first step to replace the rear compartment lift window panel emblem for the 2000 Chevrolet Corvette? Posted by Customer
    A:
    First, heat the emblem to between 32-38°C (90-100°F) to facilitate removal, then peel it from the lift window panel.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What should be avoided when handling the emblem/nameplate for the 2004 Chevrolet Corvette? Posted by Customer
    A:
    Avoid touching the adhesive backing on the emblem/nameplate.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Emblem 19207384 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 19207384 Emblem is available in the market under the name GM Emblem. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 19207384 Emblem fits certain Chevrolet Corvette models.
The original GM component designated by manufacturer part number 19207384 maintains top performance when functioning as the Emblem, Bumper/Fascia unit at its Front. The component 19207384 is constructed from durable material and its dimensions span 7.5 x 4.5 x 0.8 inches while weighing 0.50 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. The part 19207384 has available replacement options 10258164. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.