Make sure this part fits

GM 22894845
Flex Hose

2004-2012 GM

Customer Questions & Expert Answers (15)
GM 22894845 Flex Hose
  • Part Description
    Hose, Hydraulic Brake; Brake Hose
  • Position
    Rear
  • Replaces
    25928297
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2004-2012 Chevrolet ColoradoBase, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
    2004-2012 GMC CanyonSL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Can you help me check if this 22894845 is the right part for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 22894845 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What are the additional lengths needed for flares based on pipe diameter for the 2009 Chevrolet Colorado? Posted by Customer
    A:
    6.35 mm (0.250 in) for 4.76 mm (3/16 in) diameter pipe, 9.50 mm (0.374 in) for 6.35 mm (1/4 in) diameter pipe, and 12.67 mm (0.499 in) for 7.94 mm (5/16 in) diameter pipe.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What steps are involved in removing the front brake hose for the 2006 Chevrolet Colorado? Posted by Customer
    A:
    Remove the front brake hose retaining clip at the frame, then remove the bolt and gaskets from the brake caliper before taking out the brake hose from the brake caliper.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What are the final steps after replacing the brake hose for the 2007 Chevrolet Colorado? Posted by Customer
    A:
    Bleed the hydraulic brake system, install the tire and wheel assembly, and lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What should be done after detaching the brake line from the brake hose for the 2008 Chevrolet Colorado? Posted by Customer
    A:
    Remove the brake line to the left wheel cylinder, followed by the brake line to the right wheel cylinder, and install rubber caps or plugs in the brake lines.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What should be done if the new pipe needs shaping for the 2010 Chevrolet Colorado? Posted by Customer
    A:
    Shape the new pipe with a brake pipe bending tool if necessary.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    How do you connect the brake lines after installing the new brake hose for the 2010 Chevrolet Colorado? Posted by Customer
    A:
    Remove the rubber plug from the left brake line, attach it to the brake hose, and tighten the fitting to 19 Nm (14 lb ft). Repeat this for the right brake line.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    How should the rear brake hose be positioned during installation for the 2009 Chevrolet Colorado? Posted by Customer
    A:
    Position the rear brake hose on the mounting bracket and install the mounting bolt, ensuring to finger-tighten before fully tightening.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    How do you cut the brake pipe for the 2005 Chevrolet Colorado? Posted by Customer
    A:
    Cut the brake pipe squarely to the measured length using the pipe cutter included in the Brake Pipe Flaring Kit (J 45405).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What are the final steps after installing the new brake hose for the 2009 GMC Canyon? Posted by Customer
    A:
    Bleed the hydraulic brake system, install the tire and wheel assembly, and lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What is the first step to replace the rear brake hose for the 2007 GMC Canyon? Posted by Customer
    A:
    First, raise the vehicle and inspect the condition of the retaining clip; if it is flattened or damaged, discard and replace it.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What tools are needed to service and repair the brake pipes for the 2007 GMC Canyon? Posted by Customer
    A:
    The necessary tools include the Brake Pipe Flaring Kit (J 45405).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What is the procedure for installing the new brake hose for the 2010 GMC Canyon? Posted by Customer
    A:
    Use new metal copper gaskets on the brake hose, install the brake caliper bolt, and tighten it to 40 Nm (32 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What is the next step after removing the brake pipe fitting for the 2008 GMC Canyon? Posted by Customer
    A:
    Remove the front brake hose retaining clip at the frame, then remove the bolt and gaskets from the brake caliper before taking out the brake hose from the brake caliper.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What should be done after preparing the brake pipe for the 2006 GMC Canyon? Posted by Customer
    A:
    Install the tube nuts and clean the brake pipe and the Brake Pipe Flaring Kit (J 45405) of any contaminants.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Flex Hose 22894845 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 22894845 Flex Hose is available in the market under the name GM Brake Line, Hydraulic Hose. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 22894845 Flex Hose fits certain Chevrolet Colorado models, as well as GMC Canyon models.
The original GM component designated by manufacturer part number 22894845 maintains top performance when functioning as the Hose, Hydraulic Brake; Brake Hose unit at its Rear. The component 22894845 is constructed from durable material and its dimensions span 6.4 x 15.8 x 11.3 inches while weighing 1.30 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Piston. The part 22894845 has available replacement options 25928297. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.