Make sure this part fits

GM 15252284
Emblem, Front

2006-2009 Chevrolet Equinox

Customer Questions & Expert Answers (5)
GM 15252284 Emblem, Front
GM 15252284 Emblem, Front
  • Part Description
    Emblem, Radiator Grille And Front End Ornamentation
  • Position
    Front
  • Manufacturer
    General Motors
Make sure this part fits
$47.11 MSRP: $70.11
You Save: $23.00 (33%)
Ships in 1-2 Business Days
1
ADD TO CART
  • Vehicle Fitment

    Year Make Model Trim Engine
    2006-2009 Chevrolet EquinoxLS, LT, LTZ, Sport6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 15252284 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 15252284 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to properly install an emblem on a Chevrolet Equinox? Posted by Customer
    A:
    Starting with tape protection for the mounting surface you can move to create installation alignment marks for the Equinox liftgate emblem/nameplate replacement. Heat the emblem/nameplate under a heat gun in a circular pattern for 30 seconds from a distance of 152 mm (6 in) away from the surface. Disassemble the emblem/nameplate from the panel using a flat blade plastic tool. Categoria 3M(TM) Scotch Brite molding adhesive remover disk 3M(TM) P/N 07501 serves to remove body panel adhesive but body panels require either Varnish Makers and Painters (VMP) naphtha or a 50/50 mixture of isopropyl alcohol and water when used on plastic panels. Wipe down both the installation area with the same cleaning solution before completely drying it out. Apply tape first to mark the installation spot when the surface does not have any markings. The EQUINOX emblem/nameplate needs to be positioned at 11 mm (0.043 in) from the left liftgate edge and 160 mm (6.30 in) from the liftgate center to bottom. Position the CHEVROLET emblem/nameplate 31 mm (1.22 in) from the right edge while keeping it 160 mm (6.30 in) from the center to the bottom. Heat the surface to between 27-41°C (80-105°F) before placing the emblem/nameplate at temperatures between 29-32°C (85-90°F) without touching the adhesive side. First remove the protective liner from the emblem/nameplate before placing it accurately on the marks using steady and equal pressure. Remove the protective tape which covers the mounting surface.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the liftgate emblem/nameplate on Chevrolet Equinox? Posted by Customer
    A:
    Before putting on the new Equinox liftgate emblem/nameplate you need to tape the installation surface and set up alignment markers. Hold a heat gun at about 152 mm (6 inches) from the part and move the heat over the emblem/nameplate for 30 seconds in circular patterns. Insert a plastic scraper under the emblem/nameplate to pry it off from the panel. Use the 3M(TM) Scotch Brite Molding Adhesive Remover Disk (3M(TM) P/N 07501) for body panels and a Varnish Makers and Painters (VMP) Naphtha solution or water/isopropyl alcohol mixture for plastic panels to remove all leftover adhesive. Use the identical cleaning solution to wipe the installation site before fully drying it. Use tape to mark the area when there is no specified placement for the emblem. Fix the EQUINOX emblem/nameplate at the top left edge which should measure 11 mm (0.043 inches) from the liftgate and bottom center line must be placed exactly 160 mm (6.30 inches) below it. Install the CHEVROLET emblem/nameplate 31 mm (1.22 in) from the right liftgate edge with its dimension (b) matching at 160 mm (6.30 in). Use heat to raise the application area temperature between 80-105°F (80-105°F), then prep the emblem/nameplate surface for installation at 85-90°F. Stay away from touching the adhesive coating and pull off the protective material to put the emblem/nameplate at the marked spots by pressing it hard against the surface. Press evenly on all parts of the badge to seal it to the surface before taking off the tape at the rear end.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the final step after pressing the emblem/nameplate onto the surface for the 2006 Chevrolet Equinox? Posted by Customer
    A:
    Remove the protective tape from the mounting surface.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    How should the emblem/nameplate be heated for the 2007 Chevrolet Equinox? Posted by Customer
    A:
    Use a heat gun in a circular motion for about 30 seconds, keeping it approximately 152 mm (6 in) from the surface.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Emblem, Front 15252284 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 15252284 Emblem, Front is available in the market under the name GM Emblem. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 15252284 Emblem, Front fits certain Chevrolet Equinox models.
The original GM component designated by manufacturer part number 15252284 maintains top performance when functioning as the Emblem, Radiator Grille And Front End Ornamentation unit at its Front. The component 15252284 is constructed from durable material and its dimensions span 9.2 x 2.1 x 2.1 inches while weighing 0.60 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. The part 15252284 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.