Make sure this part fits

GM 25792106
Upper Weatherstrip, Driver Side

2002-2009 GM

Customer Questions & Expert Answers (15)
GM 25792106 Upper Weatherstrip, Driver Side
  • Part Description
    Sealing Strip-Lift Gate Window Side Reveal Molding
  • Position
    Driver Side
  • Replaces
    15205311, 15053257, 15102190, 15076654
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2004-2007 Buick RainierCXL, CXL Plus6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS
    2002-2009 GMC EnvoyDenali, SLE, SLT6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS
    2002-2004 Oldsmobile BravadaBase6 Cyl 4.2 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Can you help me check if this 25792106 is the right part for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 25792106 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the process for pressing the weatherstrip into place for the 2004 Buick Rainier? Posted by Customer
    A:
    Press the weatherstrip into the mid gate window channel starting at the alignment locations and working around.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What should be removed after opening the end gate and moveable roof for the 2004 Buick Rainier? Posted by Customer
    A:
    Remove the push-pins that secure the end gate weatherstrip upper mold from the moveable roof module.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What is the final step in the process for the 2005 Buick Rainier? Posted by Customer
    A:
    Slide the retaining clips down on the sliding hinge panel to release it and close the midgate.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What is the first step to replace the sunroof window weatherstrip for the 2007 Buick Rainier? Posted by Customer
    A:
    First, remove the sunroof window.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    How do you ensure the new sealing strip is properly installed for the 2006 Buick Rainier? Posted by Customer
    A:
    Ensure it is fully seated.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    Where should the lower window channel weatherstrip be inserted during installation for the 2004 GMC Envoy? Posted by Customer
    A:
    Insert it between the door inner and outer panels.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What should be done after removing the front door sill plate for the 2007 GMC Envoy? Posted by Customer
    A:
    Take off the weatherstrip from the pinch-weld flange.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    How do you remove the upper molded detail from the front of the side access door for the 2004 GMC Envoy? Posted by Customer
    A:
    Insert the Door Trim Pad Clip Remover (J 38778) under the weatherstrip mold and release the three integral retaining pins on the mold to the door.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What tool can be used to ensure full engagement of the weatherstrip for the 2006 GMC Envoy? Posted by Customer
    A:
    Use a rubber mallet to ensure full engagement of the weatherstrip to the pinch-weld flange.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What is the next step after removing the push pin retainers for the 2008 GMC Envoy? Posted by Customer
    A:
    Pull back the front door sealing weatherstrip to expose the weatherstrip side retainer screws.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What should you do after removing the screw for the 2002 GMC Envoy? Posted by Customer
    A:
    Lift upward on the forward edge of the sealing strip and remove it from the pinch-weld flange.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What is the first step to replace the liftgate weatherstrip for the 2009 GMC Envoy? Posted by Customer
    A:
    Open the liftgate and pull the weatherstrip from the liftgate opening pinch-weld flange.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What should be done after removing the upper weatherstrip for the 2005 GMC Envoy? Posted by Customer
    A:
    Remove the push-pins retaining the endgate weatherstrip lower molds to the back of the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What needs to be done with the weatherstrip side retainer screws for the 2003 GMC Envoy? Posted by Customer
    A:
    Remove these screws and take out the weatherstrip side retainer from the windshield pillar.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Upper Weatherstrip, Driver Side 25792106 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 25792106 Upper Weatherstrip, Driver Side is available in the market under the name GM Weather Strip. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 25792106 Upper Weatherstrip, Driver Side fits certain GMC Envoy models, as well as Buick Rainier. Additionally, it is compatible with Oldsmobile Bravada models.
The original GM component designated by manufacturer part number 25792106 maintains top performance when functioning as the Sealing Strip-Lift Gate Window Side Reveal Molding unit at its Driver Side. The component 25792106 is constructed from durable material and its dimensions span 26.8 x 3.5 x 3.2 inches while weighing 0.50 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Sealing Strip, Upper End Gate. The part 25792106 has available replacement options 15205311, 15053257, 15102190, 15076654. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.