Make sure this part fits

GM 10449200
Door Weatherstrip, Driver Side

1997-2008 GM

Customer Questions & Expert Answers (16)
GM 10449200 Door Weatherstrip, Driver Side
  • Part Description
    Weatherstrip, Door Weatherstrip; Door Seal
  • Position
    Driver Side
  • Replaces
    10416830, 12493210, 10443906, 10416832, 10413159, 10413160
  • Manufacturer
    General Motors
Make sure this part fits
$12.26 MSRP: $18.25
You Save: $5.99 (33%)
Ships in 1-2 Business Days
1
ADD TO CART
  • Vehicle Fitment

    Year Make Model Trim Engine
    2005-2007 Buick TerrazaCX, CXL6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
    2005-2008 Chevrolet UplanderBase, LS, LT6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
    1997-2005 Chevrolet VentureBase, LS, LT, Plus, Value, Warner Bros.6 Cyl 3.4 L GAS
    1997-2004 Oldsmobile SilhouetteBase, GL, GLS, GS, Premiere6 Cyl 3.4 L GAS
    1999-2006 Pontiac MontanaBase, SV66 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
    1998 Pontiac Trans SportBase, Montana6 Cyl 3.4 L GAS
    2005-2007 Saturn Relay1, 2, 36 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 10449200 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 10449200 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the final step in the process for the 2006 Buick Terraza? Posted by Customer
    A:
    Restore the low current logic power by installing the PSD 15A fuse back into the instrument panel fuse block.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    How do you complete the installation of the weatherstrip for the 2006 Buick Terraza? Posted by Customer
    A:
    Carefully pull the tear strip from the joint along the entire length of the weatherstrip, using a spoon if necessary.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    How should heat be applied to the sliding door auxiliary weatherstrip for the 2005 Buick Terraza? Posted by Customer
    A:
    Use a heat gun to heat the weatherstrip, keeping it 150 mm (6 in) from the surface and applying heat in a circular motion for about 30 seconds.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What should be done after heating the weatherstrip for the 2007 Buick Terraza? Posted by Customer
    A:
    Carefully peel the weatherstrip from the panel surface using a flat-bladed tool, ensuring not to damage the paint.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What should be done after heating the weatherstrip for the 2005 Chevrolet Venture? Posted by Customer
    A:
    Carefully peel the weatherstrip from the panel surface with a flat-bladed tool, ensuring not to damage the paint.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What is the first step to replace the hood rear weatherstrip for the 2004 Chevrolet Venture? Posted by Customer
    A:
    Open and support the hood.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What is the first step to replace the sliding door weatherstrip for the 2008 Chevrolet Uplander? Posted by Customer
    A:
    Disable the power sliding door system by removing the PSD 15A fuse from the instrument panel fuse block.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What should you do with the tear strip at the liftgate body wedge for the 2008 Chevrolet Uplander? Posted by Customer
    A:
    Remove the tear strip, which should pull the inner lip of the weatherstrip over the interior trim; spooning may be required for proper installation.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What should be done to ensure a proper seal before reinstalling the rear quarter window for the 2000 Chevrolet Venture? Posted by Customer
    A:
    Roll the weatherstrip from the joint to the bottom of the window.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What should be done after installing the weatherstrip for the 2001 Chevrolet Venture? Posted by Customer
    A:
    Reinstall the rear quarter window.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What should be done after removing the bottom auxiliary weatherstrip for the 2003 Chevrolet Venture? Posted by Customer
    A:
    Install the push-in retainers to the new weatherstrip.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What is the first step to replace the rear quarter window weatherstrip for the 2005 Chevrolet Uplander? Posted by Customer
    A:
    Remove the rear quarter window by following the appropriate replacement procedure for either the A20 Power or A20 Manual.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What temperature should the body panel be warmed to for installation for the 2000 Chevrolet Venture? Posted by Customer
    A:
    A minimum of 21°C (70°F).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What should be ensured while rolling the weatherstrip onto the flange for the 2002 Chevrolet Venture? Posted by Customer
    A:
    Ensure it is fully seated in the corners without stretching it.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What temperature should the body panel be warmed to for installation for the 2006 Chevrolet Uplander? Posted by Customer
    A:
    A minimum of 21°C (70°F).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Door Weatherstrip, Driver Side 10449200 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 10449200 Door Weatherstrip, Driver Side is available in the market under the name GM Weather Strip, Door Seal. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 10449200 Door Weatherstrip, Driver Side fits certain Chevrolet Uplander, Venture models, as well as Buick Terraza. Additionally, it is compatible with Pontiac Montana, Trans Sport and Oldsmobile Silhouette models.
The original GM component designated by manufacturer part number 10449200 maintains top performance when functioning as the Weatherstrip, Door Weatherstrip; Door Seal unit at its Driver Side. The component 10449200 is constructed from durable material and its dimensions span 18.9 x 18.9 x 8.4 inches while weighing 7.30 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Weatherstrip On Body; Weatherstrip, Side Door Opening; Weatherstrip. The part 10449200 has available replacement options 10416830, 12493210, 10443906, 10416832, 10413159, 10413160. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.