ChevyParts
My Garage
My Account
Cart
OEM 2000 Chevrolet Astro Ball Joint
Control Arm Joint- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
4 Ball Joints found
2000 Chevrolet Astro Ball Joint, Front Upper
Part Number: 88911387$31.25 MSRP: $55.80You Save: $24.55 (44%)Ships in 1-3 Business DaysProduct Specifications- Other Name: Joint Kit, Front Upper Control Arm Ball; Suspension Ball Joint; Upper Ball Joint; Stud Kit, Steering Knuckle Control Arm; Ball Joint Kit
- Position: Front Upper
- Replaced by: 19460397
- Item Weight: 1.80 Pounds
- Item Dimensions: 4.3 x 4.0 x 3.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 88911387
- Warranty: This genuine part is guaranteed by GM's factory warranty.
2000 Chevrolet Astro Lower Ball Joint, Front
Part Number: 15687079$44.20 MSRP: $88.75You Save: $44.55 (51%)Product Specifications- Other Name: Stud Kit, Front Lower Control Arm Ball; Suspension Ball Joint; Ball Joint; Stud Kit, Steering Knuckle Lower Control Arm Pivot
- Position: Front Lower
- Item Weight: 3.40 Pounds
- Item Dimensions: 7.0 x 4.5 x 4.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 15687079
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Product Specifications- Other Name: Hose, Power Steering Gear Inlet; Ball Joint; Upper Ball Joints; Stud Kit, Steering Knuckle Upper Control Arm
- Item Weight: 1.50 Pounds
- Item Dimensions: 12.9 x 9.4 x 5.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19146901
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Product Specifications- Other Name: Stud Kit, Front Lower Control Arm Ball; Suspension Ball Joint; Ball Joint; Stud Kit, Steering Knuckle Lower Control Arm Pivot; Front Wheel Lower Control Arm; Rear Axle Control Arm.
- Position: Front Lower
- Replaces: 09766421, 9766421
- Item Weight: 2.50 Pounds
- Item Dimensions: 6.6 x 5.1 x 4.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 88965475
- Warranty: This genuine part is guaranteed by GM's factory warranty.
2000 Chevrolet Astro Ball Joint
With a comprehensive array of OEM 2000 Chevrolet Astro Ball Joint, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2000 Chevrolet Astro Ball Joint are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.
2000 Chevrolet Astro Ball Joint Parts Questions & Experts Answers
- Q: How to service and repair the lower ball joint on 2000 Chevrolet Astro?A: Start the lower Ball Joint service by placing the vehicle on a lift then disassembling the tire and wheel elements. Next remove the front splash shield through two bolt removal and rotate it to expose the tie rods. Pull the inner Tie Rod End from its connection with the relay rod. Then take out the drive axle shaft nut and washer from the hub assembly before removing the bolts that secure the hub and bearing assembly. After that take off the lower Ball Joint cotter pin and nut. You can unload the Torsion Bar through j 36202 while keeping note of the adjuster bolt position. Place safety stand support under the lower Control Arm during unloading. Unscrew the knuckle from the lower Ball Joint using the j 35917 tool until you are ready to drill the rivets. Add the new Ball Joint to the lower Control Arm through bolt fasteners supplemented with flat washers and nuts tightened 30 nm (22 ft. Lbs.). Locate the lower Control Arm with a jack and put the Ball Joint into the knuckle. Tighten the nut to 128 nm (95 ft. Lbs.) at z height. After adding a new cotter pin accelerate the nut by an additional 1/6 turn to secure the joint and attach the lower Ball Joint grease fitting to dispense grease until it seeps from the seal. Make use of the Torsion Bar unloading/loading tool (J 36202) to load the Torsion Bar to the marked position on the adjuster bolt. Secure the hub and bearing assembly onto the knuckle by tightening bolts to 90 nm (66 ft. Lbs.) and push the drive axle through the hub assembly. Lock the parts with a washer and nut fastened to 200 nm (147 ft. Lbs.). Install the Tie Rod End back to its relay rod connection. Also put in the front splash shield and bolts with torque set to 14 nm (124 inch lbs). Lastly, put back the tire and wheel and check the front wheel alignment. To accomplish the task you will need a Tie Rod puller (J 6627-A), torsion bar unloading/loading tool (J 36202), steering linkage installer (J 29193), and Ball Joint remover (J 35917).
Related 2000 Chevrolet Astro Parts
2000 Chevrolet Astro Torsion Bar
2000 Chevrolet Astro Alignment Bolt
2000 Chevrolet Astro Axle Shaft
2000 Chevrolet Astro CV Boot
2000 Chevrolet Astro Coil Spring Insulator
2000 Chevrolet Astro Control Arm Bushing
2000 Chevrolet Astro Drive Shaft
2000 Chevrolet Astro Front Cross-Member
2000 Chevrolet Astro Shock Absorber
2000 Chevrolet Astro Spindle
2000 Chevrolet Astro Steering Knuckle
2000 Chevrolet Astro Sway Bar Link