How to replace the rear brake calipers on 2000 Chevrolet K3500?

Tilt the vehicle to the rear, remove two-thirds of the brake fluid from the master cylinder and lift it with suitable stands before you begin. Note the connection between the wheel and the hub and come apart the wheel and the tire together. Set a C-clamp on the piston, tighten it so that the piston touches the bottom of the bore and then take the C-clamp off. Now, you should remove the brake hose and then the support key (3), the bolt (2) and the spring (4). Press out the support key with a brass punch and a hammer and after that, remove the caliper assembly (1). Inside of the caliper assembly, see if any fluid is leaking; if you notice any leakage, follow the instructions in Brake Caliper Overhaul. A wire brush should be used to get rid of corrosion on the machined surfaces of both the anchor plate and caliper. While putting on the caliper, apply a layer of Shell Aeroshell Grade 5 lubricant or its equal to the moving surfaces and NOT NEVER SEIZE products. Following that, install the caliper assembly (1), the spring (4) and finish by driving the support key (3) in place using a brass punch and hammer. Set the bolt (2) into the key, make sure it fits into the immediate boss in the key and tighten it to 20 Nm (15 ft. lbs.). Place the brake hose neatly and tighten it with 45 Nm (33 ft. lbs.) of torque, being sure it isn't twisted. Drain your tires, gap the rims and then fit the assembly into place. Make sure the brake pedal is firm before moving the car and after pumping the brakes, check if the brake fluid level is adequate in the master cylinder. You should lower the vehicle at the end of the process.

OEM 2000 Chevrolet K3500 Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Brake Calipers found

View related parts
2000 Chevrolet K3500 Caliper, Passenger Side
Part Number: 19242899
$231.65 MSRP: $428.58
You Save: $196.93 (46%)
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper; Housing, Wheel Brake Cylinder/Caliper
- Position: Passenger Side
- Replaces: 14002544, 15665668
- Item Weight: 17.80 Pounds
- Item Dimensions: 9.8 x 7.5 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19242899
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet K3500 Submodels:
- Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
2000 Chevrolet K3500 Caliper, Driver Side
Part Number: 19242898
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper; Housing, Wheel Brake Cylinder/Caliper
- Position: Driver Side
- Replaces: 14002543, 15665667
- Item Weight: 17.60 Pounds
- Item Dimensions: 9.3 x 7.4 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19242898
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet K3500 Submodels:
- Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
2000 Chevrolet K3500 Caliper, Front Passenger Side
Part Number: 18014748
Product Specifications
- Other Name: Caliper Kit, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Item Weight: 11.80 Pounds
- Item Dimensions: 9.6 x 7.6 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18014748
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet K3500 Submodels:
- Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
2000 Chevrolet K3500 Caliper, Passenger Side
Part Number: 18017228
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Passenger Side
- Item Weight: 15.90 Pounds
- Item Dimensions: 9.4 x 7.6 x 4.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18017228
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet K3500 Submodels:
- Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
2000 Chevrolet K3500 Caliper, Driver Side
Part Number: 18017227
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Driver Side
- Item Weight: 15.30 Pounds
- Item Dimensions: 9.6 x 7.5 x 4.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18017227
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet K3500 Submodels:
- Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
2000 Chevrolet K3500 Caliper, Front Driver Side
Part Number: 18014747
Product Specifications
- Other Name: Caliper Kit, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Item Weight: 12.50 Pounds
- Item Dimensions: 9.6 x 7.4 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18014747
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet K3500 Submodels:
- Base, Cheyenne, LS, Scottsdale, Silverado | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS

2000 Chevrolet K3500 Brake Calipers

With a comprehensive array of OEM 2000 Chevrolet K3500 Brake Calipers, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2000 Chevrolet K3500 Brake Calipers are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2000 Chevrolet K3500 Parts Questions & Experts Answers

Q: How to replace the rear brake calipers on 2000 Chevrolet K3500?
A: Tilt the vehicle to the rear, remove two-thirds of the brake fluid from the master cylinder and lift it with suitable stands before you begin. Note the connection between the wheel and the hub and come apart the wheel and the tire together. Set a C-clamp on the piston, tighten it so that the piston touches the bottom of the bore and then take the C-clamp off. Now, you should remove the brake hose and then the support key (3), the bolt (2) and the spring (4). Press out the support key with a brass punch and a hammer and after that, remove the caliper assembly (1). Inside of the caliper assembly, see if any fluid is leaking; if you notice any leakage, follow the instructions in Brake Caliper Overhaul. A wire brush should be used to get rid of corrosion on the machined surfaces of both the anchor plate and caliper. While putting on the caliper, apply a layer of Shell Aeroshell Grade 5 lubricant or its equal to the moving surfaces and NOT NEVER SEIZE products. Following that, install the caliper assembly (1), the spring (4) and finish by driving the support key (3) in place using a brass punch and hammer. Set the bolt (2) into the key, make sure it fits into the immediate boss in the key and tighten it to 20 Nm (15 ft. lbs.). Place the brake hose neatly and tighten it with 45 Nm (33 ft. lbs.) of torque, being sure it isn't twisted. Drain your tires, gap the rims and then fit the assembly into place. Make sure the brake pedal is firm before moving the car and after pumping the brakes, check if the brake fluid level is adequate in the master cylinder. You should lower the vehicle at the end of the process.