How to replace the front brake pads on 2005 Chevrolet Corvette?

Before starting pad replacement check the brake master cylinder reservoir fluid level. If the fluid sits at midway between marks you need no fluid withdrawal while higher levels should be lowered to halfway. Support the car and take off its tire and wheel assembly. Twist the wheel lug nut by hand to hold the rotor on the hub in place. Apply a large c-clamp over the brake caliper while pushing its hooks against the rear of the caliper face. Press the brake caliper pistons into the pads with either an old Brake Pad or a wood block near the pistons until the caliper pistons move past the brake rotor. Use mechanic wire to hang the brake caliper after removing the c-clamp then taking out the top guide pin bolt. Check the Brake Pad retainers by taking off the brake pads. Inspection shows the need for repairs on any damaged caliper slide boots. Place the big c-clamp to push brake pistons fully and then remove both the clamp and previously used Brake Pad or wood block. Place the brake pads in their proper position on the new brake rotor with the Brake Pad wear sensor aligned correctly toward the rear as the rotor spins forward. Place the brake caliper in its bracket position and attach the upper guide pin bolt by tightening it to 31 nm (23 ft. Lbs.). Put the wheel and tire back onto the vehicle before lowering it down. During engine off silence, press the Brake Pedal to 2/3 of travel then release it slowly. Press the Brake Pedal 15 seconds multiple times until you feel firm pressure from the engine. This puts the brake caliper pistons and pads in the right position. Complete the brake master cylinder reservoir to the correct mark while thoroughly wiping rotors and pads together.

OEM 2005 Chevrolet Corvette Brake Pad

Disc Brake Pad Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Brake Pads found

View related parts
2005 Chevrolet Corvette Brake Pads
Part Number: 19259589
$111.85 MSRP: $199.73
You Save: $87.88 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads
- Position: Rear
- Replaces: 88964095
- Item Weight: 3.30 Pounds
- Item Dimensions: 10.3 x 4.8 x 3.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19259589
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2005 Chevrolet Corvette Submodels:
- 50th Anniversary Edition, 50th Anniversary Edition Pace Car, Base, Z06 | 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS
View related parts
2005 Chevrolet Corvette Brake Pads, Front
Part Number: 19152862
$262.53 MSRP: $485.72
You Save: $223.19 (46%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Front Disc Brake; Disc Brake Hardware Kit; Front Pads; Pad Kit, Brake
- Position: Front
- Item Weight: 4.40 Pounds
- Item Dimensions: 5.2 x 3.0 x 10.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19152862
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2005 Chevrolet Corvette Submodels:
- Base, Grand Sport, ZR1 | 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS
View related parts
2005 Chevrolet Corvette Front Pads
Part Number: 88965625
$116.18 MSRP: $208.40
You Save: $92.22 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Front Disc Brake; Disc Brake Hardware Kit; Brake Pads
- Position: Front
- Item Weight: 4.00 Pounds
- Item Dimensions: 9.1 x 6.1 x 4.8 inches
- Condition: New
- SKU: 88965625
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2005 Chevrolet Corvette Submodels:
- Base | 8 Cyl 6.0 L GAS
View related parts
2005 Chevrolet Corvette Brake Pads
Part Number: 19153020
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads
- Position: Rear
- Replaces: 19121811
- Item Weight: 4.60 Pounds
- Item Dimensions: 10.2 x 4.9 x 3.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19153020
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2005 Chevrolet Corvette Submodels:
- 427, 427 Limited Edition Z06, Base, Grand Sport, Z06, Z06 Carbon, ZR1 | 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
View related parts
2005 Chevrolet Corvette Brake Pads
Part Number: 89026853
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads
- Position: Rear
- Replaces: 88965628
- Item Weight: 4.10 Pounds
- Item Dimensions: 10.3 x 4.9 x 3.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89026853
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2005 Chevrolet Corvette Submodels:
- Base | 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS
View related parts
2005 Chevrolet Corvette Brake Pads, Front
Part Number: 19259588
Product Specifications
- Other Name: Pad Kit, Front Disc Brake; Disc Brake Hardware Kit; Front Pads; Pad Kit, Brake
- Position: Front
- Replaces: 88955513, 89060211, 89047708
- Item Weight: 5.40 Pounds
- Item Dimensions: 10.0 x 4.9 x 3.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19259588
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2005 Chevrolet Corvette Submodels:
- 427, Base | 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS

2005 Chevrolet Corvette Brake Pad

With a comprehensive array of OEM 2005 Chevrolet Corvette Brake Pad, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2005 Chevrolet Corvette Brake Pad are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2005 Chevrolet Corvette Brake Pad Parts Questions & Experts Answers

Q: How to replace the front brake pads on 2005 Chevrolet Corvette?
A: Before starting pad replacement check the brake master cylinder reservoir fluid level. If the fluid sits at midway between marks you need no fluid withdrawal while higher levels should be lowered to halfway. Support the car and take off its tire and wheel assembly. Twist the wheel lug nut by hand to hold the rotor on the hub in place. Apply a large c-clamp over the brake caliper while pushing its hooks against the rear of the caliper face. Press the brake caliper pistons into the pads with either an old Brake Pad or a wood block near the pistons until the caliper pistons move past the brake rotor. Use mechanic wire to hang the brake caliper after removing the c-clamp then taking out the top guide pin bolt. Check the Brake Pad retainers by taking off the brake pads. Inspection shows the need for repairs on any damaged caliper slide boots. Place the big c-clamp to push brake pistons fully and then remove both the clamp and previously used Brake Pad or wood block. Place the brake pads in their proper position on the new brake rotor with the Brake Pad wear sensor aligned correctly toward the rear as the rotor spins forward. Place the brake caliper in its bracket position and attach the upper guide pin bolt by tightening it to 31 nm (23 ft. Lbs.). Put the wheel and tire back onto the vehicle before lowering it down. During engine off silence, press the Brake Pedal to 2/3 of travel then release it slowly. Press the Brake Pedal 15 seconds multiple times until you feel firm pressure from the engine. This puts the brake caliper pistons and pads in the right position. Complete the brake master cylinder reservoir to the correct mark while thoroughly wiping rotors and pads together.