How to replace the front drive shaft on 2010 Chevrolet Express 3500?

The vehicle needs to be raised before starting the front propeller shaft replacement. Note the position of the front propeller shaft u-joint toward the differential yoke before you can remove the retainer bolts and u-joint retainers of the front propeller shaft. When removing the front propeller shaft from the front differential it is essential to tape the u-joint bearing caps together to prevent separation of the u-joint bearings. Drilling starts with removing the front propeller shaft from both the Transfer Case. To install the front propeller shaft fit it into the Transfer Case while removing protective tape from the u-joint and verify that both u-joint alignment marks face each other properly. Screw the front propeller shaft into the differential yoke then fasten it by using the shaft retainers. Fits the propeller shaft retainer bolts and torque them to 25 nm (18 lb ft). The first step should include inspecting Transfer Case fluid levels and checking the front differential fluid mark. These checks should happen after lowering the vehicle to the ground.

OEM 2010 Chevrolet Express 3500 Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Drive Shafts found

View related parts
2010 Chevrolet Express 3500 Drive Shaft
Part Number: 84675732
$420.52 MSRP: $715.95
You Save: $295.43 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Drive Shaft Assembly; Shaft, Propeller
- Replaces: 15794278, 20912343, 22922243, 23509060, 20912698, 25957030
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 84675732
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following 2010 Chevrolet Express 3500 Submodels:
- Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
2010 Chevrolet Express 3500 Axle Shaft, Rear Passenger Side
Part Number: 19210693
$168.86 MSRP: $265.68
You Save: $96.82 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Rear Axle Drive; Axle Shafts
- Position: Rear Passenger Side
- Replaced by: 19300170
- Item Dimensions: 39.3 x 11.5 x 8.1 inches
- Condition: New
- SKU: 19210693
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2010 Chevrolet Express 3500 Submodels:
- Base, LS, LT | 4 Cyl 2.8 L DIESEL, 8 Cyl 4.8 L FLEX, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.6 L DIESEL
View related parts
2010 Chevrolet Express 3500 Drive Shaft
Part Number: 22889825
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 15751412, 20912345
- Item Weight: 30.50 Pounds
- Item Dimensions: 81.1 x 8.2 x 7.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 22889825
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2010 Chevrolet Express 3500 Submodels:
- Base, LS, LT | 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL

2010 Chevrolet Express 3500 Drive Shaft

With a comprehensive array of OEM 2010 Chevrolet Express 3500 Drive Shaft, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2010 Chevrolet Express 3500 Drive Shaft are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2010 Chevrolet Express 3500 Drive Shaft Parts Questions & Experts Answers

Q: How to replace the front drive shaft on 2010 Chevrolet Express 3500?
A: The vehicle needs to be raised before starting the front propeller shaft replacement. Note the position of the front propeller shaft u-joint toward the differential yoke before you can remove the retainer bolts and u-joint retainers of the front propeller shaft. When removing the front propeller shaft from the front differential it is essential to tape the u-joint bearing caps together to prevent separation of the u-joint bearings. Drilling starts with removing the front propeller shaft from both the Transfer Case. To install the front propeller shaft fit it into the Transfer Case while removing protective tape from the u-joint and verify that both u-joint alignment marks face each other properly. Screw the front propeller shaft into the differential yoke then fasten it by using the shaft retainers. Fits the propeller shaft retainer bolts and torque them to 25 nm (18 lb ft). The first step should include inspecting Transfer Case fluid levels and checking the front differential fluid mark. These checks should happen after lowering the vehicle to the ground.