How to replace the ABS Control Module on Chevrolet Colorado?

Begin ABS Control Module replacement by placing clean paper together with shop towels between ABS Control Module assembly and inner fender. The ABS Control Module electrical connector should be detached before placing it behind the Brake Booster. The cleaning process with denatured alcohol covers both the master cylinder and the module before the technician detaches the brake pipes between the master cylinder and ABS Control Module assembly and removes the rear brake pipe from the cowl retainers. Place rubber plugs into each pipe component beginning with the brake pipes and followed by the brake pressure modulator valve (BPMV) and ending with the master cylinder. This will minimize brake fluid loss during the ABS Control Module assembly replacement process. First remove the mounting nuts from the ABS Control Module before taking it out of the vehicle while making sure to operate in a contamination-free environment glove-free with no shop towels present. Install a new abs module assembly when mounting screws between ABS Control Module and bpmv cannot be removed or do not break during installation. You need to remove 4 mounting screws along with 4 collars that exist between the ABS Control Module and bpmv then discard those original parts in favor of new components. Thoroughly manage the electrical connectors to avoid misalignment when rotating the abs module until the bpmv aligns correctly facing upwards. The ABS Control Module and bpmv separation requires a pry bar to be performed otherwise replace the entire abs module as an assembly. After discarding the solenoid plate along with o-rings separate the bpmv assembly for cleaning using a paper towel while applying dot-3 brake fluid to its surface area. The examination of solenoids alongside bpmv should show no signs of corrosion or contamination while bpmv assembly replacement becomes necessary. Install the new solenoid plate onto the bpmv after removing it from the ABS Control Module while installing its new o-rings onto the ABS Control Module. The ABS Control Module reception allows the installation of the bpmv and new collars. It is important to first finger tighten the ABS Control Module mounting screws for the bpmv because the final torque should be set at 5 n.m (44 lb in). Attach the abs module to the car and secure its mounting nuts at 9 n.m (80 lb in). Insert the brake pipes into the ABS Control Module assembly by securing them with proper torque force of 19 n.m (14 lb ft). Afterwards replace the rubber plugs. Repetition is required for installing the brake pipes which connect ABS Control Module assembly to master cylinder. Reestablish electrical power and hook the rear brake pipe to its cowl-mounted retainer before taking out any paper or shop towels used for shielding from contacting the ABS Control Module assembly and inner fender. Bleeding of the abs brake system must be performed after completing the programming and relearning setup.

OEM Chevrolet Colorado ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 ABS Control Modules found

View related parts
Chevrolet Colorado Control Module Part Number: 84330122
$254.38 MSRP: $498.06
You Save: $243.68 (49%)
ADD TO CART
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module
- Replaces: 84214765, 84004231
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017-2022 Chevrolet Colorado | Base, LT, WT, Z71, ZR2 | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Colorado Modulator Valve Part Number: 84644579
$392.68 MSRP: $762.13
You Save: $369.45 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Assembly-Electronic Brake Control (W/Brake Pressure Mode; ABS Control Module; ABS Control Unit; Module, Electronic Brake Control
- Replaces: 84004228, 84330123, 84214766, 84338036
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017-2022 Chevrolet Colorado | Base, LT, WT, Z71, ZR2 | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Colorado ABS Control Unit Part Number: 23414478
$477.56 MSRP: $883.54
You Save: $405.98 (46%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Assembly-Electronic Brake Control (W/Brake Pressure Mode; ABS Control Module; Module, Electronic Brake Control
- Replaces: 23284603
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016 Chevrolet Colorado | Base, LT, WT, Z71 | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Colorado Control Module Part Number: 19207520
Product Specifications
- Other Name: Module Kit, Electronic Brake Control; ABS Control Module
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2012 Chevrolet Colorado | LT, WT | 4 Cyl 2.9 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Colorado Control Module Part Number: 19121732
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 88967058, 19149182, 89040345
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2009 Chevrolet Colorado | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Colorado Control Module Part Number: 19121730
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 19149180, 89040343, 88967056
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2009 Chevrolet Colorado | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Colorado ABS Control Unit Part Number: 19121728
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 88967054, 19149184, 88964186
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2008 Chevrolet Colorado | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
Chevrolet Colorado Control Module Part Number: 85620555
Product Specifications
- Other Name: Module Kit-Electronic Brake Control; Module Kit, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 Chevrolet Colorado | LT, Trail Boss, WT, Z71, ZR2 | 4 Cyl 2.7 L GAS
View related parts
Chevrolet Colorado Control Module Part Number: 19121731
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 88967057, 89040344
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2009 Chevrolet Colorado | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Colorado ABS Control Unit Part Number: 19121729
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 19149185, 88964188, 88967055, 89040661
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2008 Chevrolet Colorado | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
Chevrolet Colorado ABS Control Unit Part Number: 19121727
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 89040659, 19149183, 88967053
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2008 Chevrolet Colorado | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
Chevrolet Colorado Control Module Part Number: 23414480
$248.88 MSRP: $446.45
You Save: $197.57 (45%)
Product Specifications
- Other Name: Module Kit-Electronic Brake Control; ABS Control Module; Modulator Valve; Module Kit, Electronic Brake Control
- Replaces: 23200278
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2016 Chevrolet Colorado | Base, LT, WT, Z71 | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Colorado Modulator Valve Part Number: 23354053
$609.11 MSRP: $1097.49
You Save: $488.38 (45%)
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module; ABS Control Unit
- Replaces: 23200277
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015 Chevrolet Colorado | Base, LT, WT, Z71 | 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L GAS

Chevrolet Colorado ABS Control Module

Want to cut long-term maintenance and repair costs? Choose OEM ABS Control Module. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Colorado parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Colorado ABS Control Module includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Chevrolet Colorado ABS Control Module invented for Anti-lock Braking System is a widely acclaimed model for reliability and performance on Chevrolet Colorado different models. This module is very essential for improving on the safety of the vehicles because it prevents locking of the wheels especially during vigorous braking thus improving on the handling of the vehicles. The ABS Control Module controls a complex structure of wheel speed sensors, valves, a pump, and the ECU, in that they constantly regulate the wheel speed as well as the brake pressure. This enhanced sort of braking system not only enhances the braking capacity but includes other genres like electronic stability control and traction control which increases the Authorization level of Chevrolet Colorado. The ABS Control Module is compatible with several generations of the Colorado due to compatibility changes brought by the constant evolution of the specifications of the truck and the drivers' need to receive similar performance features regardless of the vehicle's model year. Chevrolet Colorado is a compact to mid size pickup truck; those models are popular due to their durability and variation of usage. In the market of automobiles, ABS Control Module is the most appreciable and valuable item, which is designed elaborately to improve both performance and security. As seen, the strengths of this brand, Chevrolet Colorado ABS Control Module, has therefore become a precedent for many consumers to view this brand as suitable for use.

Chevrolet Colorado ABS Control Module Parts Questions & Experts Answers

Control Module
19121732
Q: How to replace the ABS Control Module on Chevrolet Colorado?
A:
Begin ABS Control Module replacement by placing clean paper together with shop towels between ABS Control Module assembly and inner fender. The ABS Control Module electrical connector should be detached before placing it behind the Brake Booster. The cleaning process with denatured alcohol covers both the master cylinder and the module before the technician detaches the brake pipes between the master cylinder and ABS Control Module assembly and removes the rear brake pipe from the cowl retainers. Place rubber plugs into each pipe component beginning with the brake pipes and followed by the brake pressure modulator valve (BPMV) and ending with the master cylinder. This will minimize brake fluid loss during the ABS Control Module assembly replacement process. First remove the mounting nuts from the ABS Control Module before taking it out of the vehicle while making sure to operate in a contamination-free environment glove-free with no shop towels present. Install a new abs module assembly when mounting screws between ABS Control Module and bpmv cannot be removed or do not break during installation. You need to remove 4 mounting screws along with 4 collars that exist between the ABS Control Module and bpmv then discard those original parts in favor of new components. Thoroughly manage the electrical connectors to avoid misalignment when rotating the abs module until the bpmv aligns correctly facing upwards. The ABS Control Module and bpmv separation requires a pry bar to be performed otherwise replace the entire abs module as an assembly. After discarding the solenoid plate along with o-rings separate the bpmv assembly for cleaning using a paper towel while applying dot-3 brake fluid to its surface area. The examination of solenoids alongside bpmv should show no signs of corrosion or contamination while bpmv assembly replacement becomes necessary. Install the new solenoid plate onto the bpmv after removing it from the ABS Control Module while installing its new o-rings onto the ABS Control Module. The ABS Control Module reception allows the installation of the bpmv and new collars. It is important to first finger tighten the ABS Control Module mounting screws for the bpmv because the final torque should be set at 5 n.m (44 lb in). Attach the abs module to the car and secure its mounting nuts at 9 n.m (80 lb in). Insert the brake pipes into the ABS Control Module assembly by securing them with proper torque force of 19 n.m (14 lb ft). Afterwards replace the rubber plugs. Repetition is required for installing the brake pipes which connect ABS Control Module assembly to master cylinder. Reestablish electrical power and hook the rear brake pipe to its cowl-mounted retainer before taking out any paper or shop towels used for shielding from contacting the ABS Control Module assembly and inner fender. Bleeding of the abs brake system must be performed after completing the programming and relearning setup.