How to service and repair the Exhaust Pipe on Chevrolet Metro?

The process of servicing or repairing the Exhaust Pipe starts with assigning support to the vehicle before lifting it. Unfasten two bolts to detach the front pipe/twc assembly which exists on top of the Exhaust Manifold and extract the electrical connector from the heated Oxygen Sensor (H02S2) . The service requires removal of the front pipe/twc assembly from the resonator/muffler/tail pipe assembly by uninstalling two nuts. Then you must take out the hanger which supports the twc followed by extracting the front pipe/twc assembly from the vehicle. Wash the sealing area of the front pipe/twc assembly before putting in the new front pipe/twc components. The front pipe/twc assembly should be attached to the resonator/muffler/tail pipe assembly with new gasket while maintaining a secure placement with two nuts that do not reach full torque. First install a new seal before attaching the front pipe/twc assembly to the Exhaust Manifold through two bolts while leaving them loose. Reinstall the heated Oxygen Sensor (H02S2) electrical connector at this time. Alignment checks should come first before you begin tightening the fasteners to stop noise and vibrations from occurring. Use a torque wrench to tighten bolts that connect the front pipe/twc assembly to the Exhaust Manifold to 50 nm (37 ft. Lbs.) and those connecting the front pipe/twc assembly to the resonator/muffler/tail pipe assembly to 35 nm (26 ft. Lbs.). Finally, lower the vehicle.

OEM Chevrolet Metro Exhaust Pipe

Exhaust Tail Pipe

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Exhaust Pipes found

View related parts
Chevrolet Metro Muffler & Pipe Part Number: 30019408
Product Specifications
- Other Name: Muffler, Exhaust; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Muffler
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2001 Chevrolet Metro | Base, LSi | 3 Cyl 1.0 L GAS, 4 Cyl 1.3 L GAS
View related parts
Chevrolet Metro Muffler & Pipe Part Number: 30019407
Product Specifications
- Other Name: Muffler, Exhaust; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Muffler
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2000 Chevrolet Metro | Base, LSi | 3 Cyl 1.0 L GAS, 4 Cyl 1.3 L GAS
View related parts
Chevrolet Metro Catalytic Converter Part Number: 30016363
Product Specifications
- Other Name: Converter, Catalytic (W/Exhaust Pipe); Exhaust Pipe; Converter, Catalytic Converter; Converter, Exhaust Pipe
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2000 Chevrolet Metro | Base, LSi | 3 Cyl 1.0 L GAS, 4 Cyl 1.3 L GAS

Chevrolet Metro Exhaust Pipe

Want to cut long-term maintenance and repair costs? Choose OEM Exhaust Pipe. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Metro parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Metro Exhaust Pipe includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Chevrolet Metro Exhaust Pipe is one part which speaks a lot about the solidity and capability of the Chevrolet Metro series which has been introduced in the subcompact car segment in 1998. Built to effectively release unwanted fumes such as carbon monoxide from the engine, the Chevrolet Metro Exhaust Pipe helps to prevent the dangerous fumes from coming inside the car thus increasing the safety of passengers. Suitable to a variety of Metro cars and the hatch and sedan types in particular, this exhaust pipe is a key component in the efficiency of a car's engine and its overall performance. This car model is in fact the Chevrolet Metro, a car that boasts a marvelous fuel economy figure of up to 42 mpg on the highway and this is owed in part to a properly designed exhaust system that includes the exhaust pipe, the muffler, and the catalytic converter all well unified to minimize emissions while at the same time improving the car's gas mileage. Specifically, the Chevrolet Metro Exhaust Pipe features a corrosion and wear-resistant material choose to protect against any wear and tear that the vehicle is likely to go through in a given period of use. These help in preventing problems such as vibration of the car body, or exhaust problems which are major factors of risk to the safety of the vehicle. Chevrolet Metro Exhaust Pipe is a very important and competitively priced product in the car's exhaust system mainly because the Chevrolet is a car that is mostly associated with efficiency and safety and thus any part that makes the car less safe is very important for any car owner who wants to maintain the efficiency and safety of the car.

Chevrolet Metro Exhaust Pipe Parts Questions & Experts Answers

Catalytic Converter
30016363
Q: How to service and repair the Exhaust Pipe on Chevrolet Metro?
A:
The process of servicing or repairing the Exhaust Pipe starts with assigning support to the vehicle before lifting it. Unfasten two bolts to detach the front pipe/twc assembly which exists on top of the Exhaust Manifold and extract the electrical connector from the heated Oxygen Sensor (H02S2) . The service requires removal of the front pipe/twc assembly from the resonator/muffler/tail pipe assembly by uninstalling two nuts. Then you must take out the hanger which supports the twc followed by extracting the front pipe/twc assembly from the vehicle. Wash the sealing area of the front pipe/twc assembly before putting in the new front pipe/twc components. The front pipe/twc assembly should be attached to the resonator/muffler/tail pipe assembly with new gasket while maintaining a secure placement with two nuts that do not reach full torque. First install a new seal before attaching the front pipe/twc assembly to the Exhaust Manifold through two bolts while leaving them loose. Reinstall the heated Oxygen Sensor (H02S2) electrical connector at this time. Alignment checks should come first before you begin tightening the fasteners to stop noise and vibrations from occurring. Use a torque wrench to tighten bolts that connect the front pipe/twc assembly to the Exhaust Manifold to 50 nm (37 ft. Lbs.) and those connecting the front pipe/twc assembly to the resonator/muffler/tail pipe assembly to 35 nm (26 ft. Lbs.). Finally, lower the vehicle.