How to replace a two-piece drive shaft on Chevrolet S10?

Begin two-piece propeller shaft replacement by performing reference marks accurately on all driveline components regarding their propeller shaft and axles positions before removing parts such as the propeller shaft as well as drive axles and pinion flanges and output shafts keeping the original part positioning relations. Detach the center bearing support bracket from the crossmember before removing necessary bolts or yoke retainers from the pinion flange of the rear axle. Extract the rear propeller shaft through the spline shaft and discharge it from the transmission or Transfer Case rear end. Clean all bearing cap surfaces and bearing straps together with the pinion yoke of corrosion using crocus cloth or 400 grit sandpaper before cleaning them with an approved solvent. The technician should check the front Slip Yoke for outer surface burrs and evaluate the wear of Slip Yoke splines while inspecting bearing cup installation and uniform seating and looking for spline twist or incorrect Universal Joint fit. Front propeller shaft stub shaft installation requires at least a sufficient grease coating on its splines while missing grease requires chassis grease use (GM P/N 12377985 or equivalent). Before attachment the front propeller shaft should be installed to transmission or Transfer Case while aligning index splines and ensuring the rear propeller shaft gets installed with its center bearing before the splines of both shafts properly mesh. Install the rear propeller shaft first onto the pinion flange/yoke before tightening the single Universal Joint yoke retainers/gym bolts to 20 nm for single joints and double cardan joint flange bolts to 45 nm. The center bearing alignment must be performed to safeguard the propeller shaft assembly by securing it at 89-91 degrees perpendicular to the propeller shaft during bolt installation. Before lowering the vehicle complete the installation of center bearing bolts to crossmember securing the support bolts with a torque of 70 nm (50 ft. Lbs.).

OEM Chevrolet S10 Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

33 Drive Shafts found

View related parts
Chevrolet S10 Drive Shaft
Part Number: 15036984
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2004 Chevrolet S10 | Base, LS, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Drive Shaft
Part Number: 15982636
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Chevrolet S10 | Base, LS, SS | 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Drive Shaft, Front
Part Number: 7841336
Product Specifications
- Other Name: Shat Assembly-Front Propeller; Driveshaft; Shaft, Propeller
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1994 Chevrolet S10 | Baja, Base, Durango, EL, LS, Sport, Tahoe, ZR2 | 4 Cyl 1.9 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Drive Shaft, Rear
Part Number: 26033684
Product Specifications
- Other Name: Shaft Assembly-Rear Propeller; Driveshaft; Shaft, Propeller
- Position: Rear
- Replaces: 19201892
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994 Chevrolet S10 | Base, LS, SS | 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Drive Shaft
Part Number: 15036998
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2003 Chevrolet S10 | Base, LS, Xtreme | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Drive Shaft
Part Number: 7844401
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 Chevrolet S10 | Baja, Base, EL, Tahoe | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Drive Shaft
Part Number: 26042972
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1995 Chevrolet S10 | Base, LS, SS | 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Drive Shaft
Part Number: 7844404
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1994 Chevrolet S10 | Baja, Base, EL, LS, Tahoe, ZR2 | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Drive Shaft
Part Number: 15088444
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 15708720
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2003 Chevrolet S10 | Base, LS, Xtreme | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Drive Shaft, Rear
Part Number: 7837420
Product Specifications
- Other Name: Shaft Assembly.Propeller (Rear); Driveshaft; Shaft, Propeller
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1994 Chevrolet S10 | Baja, Base, Durango, EL, LS, Sport, SS, Tahoe | 4 Cyl 1.9 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L DIESEL, 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Drive Shaft
Part Number: 15036995
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-2003 Chevrolet S10 | Base, LS, SS, Xtreme | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Drive Shaft
Part Number: 15036991
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 26051106
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2003 Chevrolet S10 | Base, LS, Xtreme | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Drive Shaft
Part Number: 26051109
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-2002 Chevrolet S10 | Base, LS, SS, Xtreme | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Drive Shaft, Rear
Part Number: 7841488
Product Specifications
- Other Name: Shaft Assembly-Rear Propeller; Driveshaft; Shaft, Propeller
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1994 Chevrolet S10 | Baja, Base, Durango, EL, LS, Sport, Tahoe, ZR2 | 4 Cyl 1.9 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Drive Shaft
Part Number: 15727234
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Chevrolet S10 | Base, LS, ZR2 | 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Drive Shaft, Front
Part Number: 26041068
Product Specifications
- Other Name: Shaft Assembly-Front Propeller; Driveshaft; Shaft, Propeller
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1994 Chevrolet S10 | Base, EL, LS, SS, Tahoe | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Drive Shaft
Part Number: 15036994
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003 Chevrolet S10 | Base, LS, Xtreme | 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Drive Shaft, Front
Part Number: 7845814
Product Specifications
- Other Name: Shaft Assembly-Front Propeller; Driveshaft; Shaft, Propeller
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1993 Chevrolet S10 | Baja, Base, Durango, EL, Sport, Tahoe | 4 Cyl 1.9 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Drive Shaft
Part Number: 15043839
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 26049789
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-1999 Chevrolet S10 | Base, LS, SS, Xtreme, ZR2 | 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Drive Shaft, Front
Part Number: 26039018
Product Specifications
- Other Name: Shaft Assembly-Front Propeller; Driveshaft; Shaft, Propeller
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Chevrolet S10 | Base, LS, SS | 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS

| Page 1 of 2 |Next >

1-20 of 33 Results

Chevrolet S10 Drive Shaft

Our website offers an extensive catalog of genuine Chevrolet S10 Drive Shaft at unbeatable prices. Every OEM Chevrolet S10 Drive Shaft comes with a manufacturer's warranty, an easy return policy, and rapid delivery service. Don't miss out on this great opportunity!

Chevrolet S10 Drive Shaft Parts Questions & Experts Answers

Drive Shaft
15036984
Q: How to replace a two-piece drive shaft on Chevrolet S10?
A: Begin two-piece propeller shaft replacement by performing reference marks accurately on all driveline components regarding their propeller shaft and axles positions before removing parts such as the propeller shaft as well as drive axles and pinion flanges and output shafts keeping the original part positioning relations. Detach the center bearing support bracket from the crossmember before removing necessary bolts or yoke retainers from the pinion flange of the rear axle. Extract the rear propeller shaft through the spline shaft and discharge it from the transmission or Transfer Case rear end. Clean all bearing cap surfaces and bearing straps together with the pinion yoke of corrosion using crocus cloth or 400 grit sandpaper before cleaning them with an approved solvent. The technician should check the front Slip Yoke for outer surface burrs and evaluate the wear of Slip Yoke splines while inspecting bearing cup installation and uniform seating and looking for spline twist or incorrect Universal Joint fit. Front propeller shaft stub shaft installation requires at least a sufficient grease coating on its splines while missing grease requires chassis grease use (GM P/N 12377985 or equivalent). Before attachment the front propeller shaft should be installed to transmission or Transfer Case while aligning index splines and ensuring the rear propeller shaft gets installed with its center bearing before the splines of both shafts properly mesh. Install the rear propeller shaft first onto the pinion flange/yoke before tightening the single Universal Joint yoke retainers/gym bolts to 20 nm for single joints and double cardan joint flange bolts to 45 nm. The center bearing alignment must be performed to safeguard the propeller shaft assembly by securing it at 89-91 degrees perpendicular to the propeller shaft during bolt installation. Before lowering the vehicle complete the installation of center bearing bolts to crossmember securing the support bolts with a torque of 70 nm (50 ft. Lbs.).

Related Chevrolet S10 Parts

Browse Chevrolet S10 Drive Shaft by Years

2004 2003 2002 2001 2000 1999 1998 1997 1996 1995 1994 1993 1992 1991 1990 1989 1988 1987 1986 1985 1984