What tools are required to replace the drive pinion bearings on a 10.5-inch axle on Chevrolet Silverado 1500 Classic?

Article j 22761 and j 8614-01 will be necessary to perform drive Pinion Bearing replacements on a 10.5-inch axle. The tool list expands to article j 37624 and j 24433, j 22912-b, j 44414, j 8608, and j 8092. Start by elevating the vehicle then proceed to take out the Differential assembly followed by the pinion gear bearing retainer and then the pinion yoke and oil seal. Remove the outer and inner pinion bearings together with the collapsible spacer and pinion gear pilot bearing. The Differential side bearing installer (J 22761) must be used to install the pinion gear pilot bearing while the Pinion Bearing installer (J 37624) and universal driver handle - 3/4 in - 10 (J 8092) are needed for the inner Pinion Bearing cup then the rear Pinion Bearing installer (J 8608) with universal driver handle - 3/4 in - 10 (J 8092) for the outer Pinion Bearing cup installation. The installation process starts with using a pinion cone and side bearing installer (J 24433) to add the inner Pinion Bearing. Afterward, install a new collapsible spacer and apply lubrication to the pinion bearings. The system requires the following procedure: install an outer Pinion Bearing and then a new pinion oil seal while using the rear axle pinion oil seal installer (J 44414) and then place the pinion within the bearing retainer. Use sealant gm p/n 12346004 or canadian p/n 10953480 on the pinion yoke splines then install the yoke and tighten the pinion nut while keeping the flange and pulley holding tool (J 8614-01) until the pinion end play reaches its limit. Install the original shim or substitute with a 0.41 mm shim if unavailable on the flange and pulley holding tool (J 8614-01). Secure the pinion gear bearing retainer in place to the axle housing with bolts fastened to 88 nm (65 ft. Lbs.). Verify that the pinion rotating torque meets the specified values by adjusting as required. After rebuilding the Differential assembly drivers must adjust the Differential side bearing preload followed by selecting appropriate drive pinion shims and adjusting backlash before filling with lubricant and lowering the vehicle.

OEM Chevrolet Silverado 1500 Classic Pinion Bearing

Transmission Pinion Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Pinion Bearings found

View related parts
Chevrolet Silverado 1500 Classic Wheel Bearing
Part Number: 9436881
$76.25 MSRP: $145.36
You Save: $69.11 (48%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential; Differential Pinion Bearing; Differential Bearing; Axle Bearings; Shaft; Inner; Side; Differential Gear; Front Wheel; Rear Wheel; Nut.
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 Classic | Hybrid, LS, LT, SS, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Silverado 1500 Classic Pinion Bearings
Part Number: 9413427
$56.84 MSRP: $109.76
You Save: $52.92 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Drive Pinion Gear Outer; Differential Pinion Bearing; Rear, Front, Outer Pinion Bearings; Differential Drive, Steering Knuckle King, Pinion Shaft, Front Axle Bearings.
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 Classic | Hybrid, LS, LT, SS, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Silverado 1500 Classic Pinion Bearings, Inner
Part Number: 457108
$55.00 MSRP: $154.36
You Save: $99.36 (65%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Drive Pinion Gear Inner; Differential Pinion Bearing; Rear Pinion Bearing; Front Pinion Bearing; Inner Pinion Bearing; Differential Drive Pinion Bearings.
- Position: Inner
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 Classic | Hybrid, LS, LT, SS, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Silverado 1500 Classic Pinion Bearings
Part Number: 454021
$161.60 MSRP: $292.48
You Save: $130.88 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly, Differential Drive Pinion Gear; Differential Pinion Bearing; Rear Pinion Bearing; Inner Pinion Bearing; Differential Drive Pinion; Rear Wheel Bearing.
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 Classic | Hybrid, LS, LT, SS, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Silverado 1500 Classic Side Bearings
Part Number: 25824250
$72.20 MSRP: $140.14
You Save: $67.94 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Side Gear; Differential Pinion Bearing; Differential Bearing
- Replaces: 09418390, 9418390
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 Classic | Hybrid, LS, LT, SS, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Silverado 1500 Classic Pinion Bearings
Part Number: 23243839
$71.22 MSRP: $139.44
You Save: $68.22 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Pinion; Differential Pinion Bearing; Rear Pinion Bearing; Front/Inner/Outer Pinion; Diff/Drive Axle; Pinion/Clutch/Rear Wheel
- Position: Front
- Replaces: 09418357, 26053758, 9418357, 15286375, 20997052, 22786621, 9418356, 09418356, 12479221
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 Classic | Hybrid, LS, LT, SS, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Silverado 1500 Classic Side Bearings
Part Number: 11505123
$56.18 MSRP: $166.26
You Save: $110.08 (67%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Side Gear; Differential Pinion Bearing; Differential Bearing; Bearing
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 Classic | Hybrid, LS, LT, SS, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Silverado 1500 Classic Pinion Bearings
Part Number: 9417781
$43.00 MSRP: $103.28
You Save: $60.28 (59%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Front Differential Drive Pinion Gear Outer; Differential Pinion Bearing; Rear, Front, Outer Pinion Bearing; Differential Drive Pinion Front, Drive Pinion, Pinion Shaft Front, Front Axle
- Position: Front Outer
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 Classic | Hybrid, LS, LT, SS, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Silverado 1500 Classic Pinion Bearings
Part Number: 9414917
$70.11 MSRP: $133.08
You Save: $62.97 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Drive Pinion Gear Inner; Differential Pinion Bearing; Differential Bearing; Rear Pinion Bearing; Drive Pinion Rear; Axle Pinion Shaft; Ring And Pinion; Pinion Shaft Front.
- Position: Inner
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 Classic | Hybrid, LS, LT, SS, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS

Chevrolet Silverado 1500 Classic Pinion Bearing

Our website offers an extensive catalog of genuine Chevrolet Silverado 1500 Classic Pinion Bearing at unbeatable prices. Every OEM Chevrolet Silverado 1500 Classic Pinion Bearing comes with a manufacturer's warranty, an easy return policy, and rapid delivery service. Don't miss out on this great opportunity!

Chevrolet Silverado 1500 Classic Pinion Bearing Parts Questions & Experts Answers

Pinion Bearings
9413427
Q: What tools are required to replace the drive pinion bearings on a 10.5-inch axle on Chevrolet Silverado 1500 Classic?
A: Article j 22761 and j 8614-01 will be necessary to perform drive Pinion Bearing replacements on a 10.5-inch axle. The tool list expands to article j 37624 and j 24433, j 22912-b, j 44414, j 8608, and j 8092. Start by elevating the vehicle then proceed to take out the Differential assembly followed by the pinion gear bearing retainer and then the pinion yoke and oil seal. Remove the outer and inner pinion bearings together with the collapsible spacer and pinion gear pilot bearing. The Differential side bearing installer (J 22761) must be used to install the pinion gear pilot bearing while the Pinion Bearing installer (J 37624) and universal driver handle - 3/4 in - 10 (J 8092) are needed for the inner Pinion Bearing cup then the rear Pinion Bearing installer (J 8608) with universal driver handle - 3/4 in - 10 (J 8092) for the outer Pinion Bearing cup installation. The installation process starts with using a pinion cone and side bearing installer (J 24433) to add the inner Pinion Bearing. Afterward, install a new collapsible spacer and apply lubrication to the pinion bearings. The system requires the following procedure: install an outer Pinion Bearing and then a new pinion oil seal while using the rear axle pinion oil seal installer (J 44414) and then place the pinion within the bearing retainer. Use sealant gm p/n 12346004 or canadian p/n 10953480 on the pinion yoke splines then install the yoke and tighten the pinion nut while keeping the flange and pulley holding tool (J 8614-01) until the pinion end play reaches its limit. Install the original shim or substitute with a 0.41 mm shim if unavailable on the flange and pulley holding tool (J 8614-01). Secure the pinion gear bearing retainer in place to the axle housing with bolts fastened to 88 nm (65 ft. Lbs.). Verify that the pinion rotating torque meets the specified values by adjusting as required. After rebuilding the Differential assembly drivers must adjust the Differential side bearing preload followed by selecting appropriate drive pinion shims and adjusting backlash before filling with lubricant and lowering the vehicle.

Related Chevrolet Silverado 1500 Classic Parts

Browse Chevrolet Silverado 1500 Classic Pinion Bearing by Years

2007