Make sure this part fits

GM 19207442
Caliper

2003-2009 GM

Customer Questions & Expert Answers (14)
GM 19207442 Caliper
  • Part Description
    Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
  • Position
    Front
  • Replaces
    89060360, 88959949
  • Manufacturer
    General Motors
Make sure this part fits
$115.70 MSRP: $351.46
You Save: $235.76 (68%)
1
ADD TO CART
  • Vehicle Fitment

    Year Make Model Trim Engine
    2003-2007 Cadillac CTSBase, Luxury, Luxury Sport6 Cyl 2.8 L GAS, 6 Cyl 3.2 L GAS, 6 Cyl 3.6 L GAS
    2005-2009 Cadillac STSBase, Platinum, V6 Cyl 3.6 L GAS, 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 19207442 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 19207442 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the procedure during assembly for the 2004 Cadillac CTS? Posted by Customer
    A:
    Install the brake caliper bleeder valve and tighten it to 14 Nm (124 inch lbs.), then lubricate and install the new piston seal into the caliper bore.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the final step in the assembly process for the 2006 Cadillac CTS? Posted by Customer
    A:
    Install the new piston dust boot seals and use the J 8092 and J 45507 to fully seat the dust boot seal into the caliper before reinstalling the caliper to the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How should the components be dried for the 2005 Cadillac CTS? Posted by Customer
    A:
    Dry the components with non-lubricated, filtered air and inspect for any damage.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How do you compress the caliper piston for the 2004 Cadillac CTS? Posted by Customer
    A:
    Use a C-clamp installed to the center of the outer brake pad and the back of the caliper to slowly compress the caliper piston.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How long should the threadlocker cure for the 2007 Cadillac CTS? Posted by Customer
    A:
    About 10 minutes.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done after removing the pistons for the 2003 Cadillac CTS? Posted by Customer
    A:
    Remove the piston dust boot seal and piston seal using a small wooden or plastic tool, then remove the brake caliper bleeder valve cap and bleeder valve.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the final step after completing the brake caliper replacement for the 2007 Cadillac STS? Posted by Customer
    A:
    Reinstall the tire and wheel assembly and lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done after inspecting the fluid level for the 2003 Cadillac CTS? Posted by Customer
    A:
    Raise and support the vehicle, then remove the tire and wheel assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How do you bleed the hydraulic brake system for the 2008 Cadillac STS? Posted by Customer
    A:
    Bleed the hydraulic brake system, then with the engine off, gradually apply the brake pedal to about 2/3 of its travel, slowly release it, and repeat until a firm pedal is achieved.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How should the new piston seal be prepared before installation for the 2006 Cadillac STS? Posted by Customer
    A:
    Lubricate it with Delco Supreme 11(R), GM P/N 12377967 (Canadian P/N 992667) or equivalent DOT-3 brake fluid.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the next step after compressing the caliper pistons for the 2009 Cadillac STS? Posted by Customer
    A:
    Remove the brake hose to caliper bolt and the brake hose from the caliper, discarding the two copper brake hose gaskets.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be placed between the caliper and the piston during piston removal for the 2007 Cadillac STS? Posted by Customer
    A:
    A 25 mm (1 in) block of wood.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How is the new piston dust boot seal installed for the 2005 Cadillac STS? Posted by Customer
    A:
    Place it over the piston and use the J8092 and J45507 to fully seat it into the caliper, ensuring it is properly seated in the groove.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Caliper 19207442 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 19207442 Caliper is available in the market under the name GM Brake Calipers. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 19207442 Caliper fits certain Cadillac CTS, STS models.
The original GM component designated by manufacturer part number 19207442 maintains top performance when functioning as the Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper unit at its Front. The component 19207442 is constructed from durable material and its dimensions span 7.2 x 4.0 x 12.5 inches while weighing 6.10 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. The part 19207442 has available replacement options 89060360, 88959949. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.