Make sure this part fits

GM 19366677
Flex Hose, Rear Passenger Side

2006-2011 GM

Customer Questions & Expert Answers (13)
GM 19366677 Flex Hose, Rear Passenger Side
  • Part Description
    Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line
  • Position
    Rear Passenger Side
  • Replaces
    15283582
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2006-2011 Buick LucerneCX, CXL, CXL Special Edition, CXS, Super6 Cyl 3.8 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 4.6 L GAS
    2006-2011 Cadillac DTSBase, Livery, Luxury, Platinum, Premium8 Cyl 4.6 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 19366677 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 19366677 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What are the final steps after installing the brake hose for the 2007 Buick Lucerne? Posted by Customer
    A:
    Bleed the brake caliper at the bleeder screw, install the tire and wheel assembly, and lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What should be done with the two copper brake hose gaskets for the 2008 Buick Lucerne? Posted by Customer
    A:
    Discard them if they are stuck to the caliper or hose end.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What should be ensured while attaching the brake hose for the 2010 Buick Lucerne? Posted by Customer
    A:
    Ensure the hose is not twisted or kinked.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What is the torque specification for the brake pipe fitting for the 2006 Buick Lucerne? Posted by Customer
    A:
    Remove the rubber cap from the brake pipe fitting and install the fitting to the brake hose, tightening it to 15 Nm (11 ft. lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What should be done during installation of the new brake hose for the 2008 Buick Lucerne? Posted by Customer
    A:
    Remove the rubber plug from the brake hose bolt hole, use NEW copper brake hose gaskets, assemble the brake hose bolt with the new gaskets, and install it to the brake caliper, tightening it to 40 N.m (30 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What should be done with the copper brake hose gaskets for the 2009 Buick Lucerne? Posted by Customer
    A:
    Discard the two copper brake hose gaskets, which may stick to the caliper or hose end.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What torque specifications should be followed for tightening the brake hose bolt for the 2009 Cadillac DTS? Posted by Customer
    A:
    Tighten to 40 Nm (30 lb ft) for JL9 or 45 Nm (33 lb ft) for J55.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What is the first step to replace the front brake hose for the 2007 Cadillac DTS? Posted by Customer
    A:
    Raise and support the vehicle, then remove the tire and wheel assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What should be done after installing the brake pipe fitting to the brake hose for the 2007 Cadillac DTS? Posted by Customer
    A:
    Tighten it to 15 N.m (11 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What should be done after removing the tire and wheel assembly for the 2010 Cadillac DTS? Posted by Customer
    A:
    Clean all dirt and foreign material from the brake hose and brake pipe fittings, capping the brake pipe fitting to prevent fluid loss and contamination.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    How should the brake hose be assembled and installed for the 2008 Cadillac DTS? Posted by Customer
    A:
    Assemble the brake hose bolt and new gaskets to the brake hose, then install the brake hose to the caliper bolt, tightening it to the specified torque.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What should be done after attaching the brake hose to the bracket for the 2006 Cadillac DTS? Posted by Customer
    A:
    Install the brake hose retainer, remove the rubber cap from the brake pipe fitting, and connect the brake pipe fitting to the brake hose, tightening it to 15 Nm (11 ft. lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Flex Hose, Rear Passenger Side 19366677 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 19366677 Flex Hose, Rear Passenger Side is available in the market under the name GM Brake Line, Hydraulic Hose. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 19366677 Flex Hose, Rear Passenger Side fits certain Cadillac DTS models, as well as Buick Lucerne models.
The original GM component designated by manufacturer part number 19366677 maintains top performance when functioning as the Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line unit at its Rear Passenger Side. The component 19366677 is constructed from durable material and its dimensions span 2.1 x 13.8 x 1.0 inches while weighing 0.60 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Hose, Hydraulic Brake. The part 19366677 has available replacement options 15283582. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.