Make sure this part fits

GM 19366781
Flex Hose, Rear Driver Side

2004-2013 GM

Customer Questions & Expert Answers (14)
GM 19366781 Flex Hose, Rear Driver Side
  • Part Description
    Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line
  • Position
    Rear Driver Side
  • Replaces
    10307425, 15802375, 20989693
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2004-2009 Cadillac XLRBase, Platinum, V8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
    2005-2013 Chevrolet CorvetteBase8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 19366781 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 19366781 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be done if the new pipe needs shaping for the 2004 Cadillac XLR? Posted by Customer
    A:
    Shape the new pipe with a brake pipe bending tool.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What should be done after removing the tire and wheel assembly for the 2009 Cadillac XLR? Posted by Customer
    A:
    Clean any dirt from the brake hose and brake pipe fitting.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What is the next step after attaching the brake hose to the bracket for the 2007 Cadillac XLR? Posted by Customer
    A:
    Remove the rubber cap or plug from the exposed brake pipe fitting end and connect the brake pipe fitting to the brake hose using a backup wrench, tightening it to 18 N.m (13 lb ft) without bending the bracket or pipe.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What is the next step after removing the brake hose for the 2009 Cadillac XLR? Posted by Customer
    A:
    Remove the brake caliper inlet fitting bolt and detach the brake hose from the caliper.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What preparation is needed before flaring for the 2007 Cadillac XLR? Posted by Customer
    A:
    Install the tube nuts, clean the brake pipe and the J 45405 of any contaminants, and prepare for flaring by loosening the die clamping screw and installing the die halves.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    How should the brake hose be attached after installation for the 2005 Cadillac XLR? Posted by Customer
    A:
    Attach the brake hose to the hose bracket, ensuring it is not kinked or twisted, and install the retainer onto the brake hose fitting at the bracket.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What are the final steps after connecting the brake pipe fitting for the 2008 Cadillac XLR? Posted by Customer
    A:
    Install the tire and wheel assembly, bleed the hydraulic brake system, and lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What is the torque specification for connecting the brake pipe fitting for the 2010 Chevrolet Corvette? Posted by Customer
    A:
    Tighten it to 18 Nm (13 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What safety precautions should be followed for the 2006 Chevrolet Corvette? Posted by Customer
    A:
    Follow safety precautions regarding brake fluid irritants and use double-walled steel brake pipes to prevent system failure.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What should be done to form the pipe for the 2010 Chevrolet Corvette? Posted by Customer
    A:
    Select the appropriate forming mandrel, close the hydraulic fluid control valve, and operate the lever of the J 45405 until the mandrel bottoms against the clamping dies.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What is the next step after attaching the brake hose to the hose bracket for the 2005 Chevrolet Corvette? Posted by Customer
    A:
    Remove the rubber cap or plug from the brake pipe fitting end and connect the brake pipe fitting to the brake hose using a backup wrench, tightening it to 18 Nm (13 ft. lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What should be done after chamfering the pipe for the 2007 Chevrolet Corvette? Posted by Customer
    A:
    Install the tube nuts, clean the pipe and tool of any debris, and loosen the die clamping screw.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What is the process for creating the flare for the 2008 Chevrolet Corvette? Posted by Customer
    A:
    Firmly tighten the die clamping screw, select the appropriate forming mandrel, and operate the lever of the J 45405 to create the flare.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Flex Hose, Rear Driver Side 19366781 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 19366781 Flex Hose, Rear Driver Side is available in the market under the name GM Brake Line. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 19366781 Flex Hose, Rear Driver Side fits certain Chevrolet Corvette models, as well as Cadillac XLR models.
The original GM component designated by manufacturer part number 19366781 maintains top performance when functioning as the Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line unit at its Rear Driver Side. The component 19366781 is constructed from durable material and its dimensions span 3.0 x 2.1 x 17.3 inches while weighing 0.60 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Hose, Hydraulic Brake. The part 19366781 has available replacement options 10307425, 15802375, 20989693. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.