Menu
×
Search Bar
Search by Part Number, Part Name, or Vehicle
My Garage
Cart
Help Center Contact Us
Make sure this part fits

GM 20934197
Power Steering Pressure Hose

2006-2012 GM

Customer Questions & Expert Answers (5)
GM 20934197 Power Steering Pressure Hose
GM 20934197 Power Steering Pressure Hose
GM 20934197 Power Steering Pressure Hose
  • Part Description
    Hose, Hydraulic Steering Gear Pressure; Power Steering Hose
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • 2010 Chevy Colorado Power Steering Pressure Hose Diagram for 20934197
    The diagram listed above is for your reference. View diagram for your vehicle

    Related Parts for 20934197

  • Vehicle Fitment

    Year Make Model Trim Engine
    2006-2012 Chevrolet ColoradoLS, LT, WT4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS
    2006-2012 GMC CanyonSL, SLE, SLT, WT4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS
    Warning: California's Proposition 65

  • Customer Questions & Expert Answers

    Q:
    Can you help me check if this 20934197 is the right part for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 20934197 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the Power Steering Hose inlet and outlet on engines with 2.9L and 3.7L on Chevrolet Colorado? Posted by Customer
    A:
    Start the replacement of power steering gear inlet and outlet hoses on llv and llr models with 2.9l and 3.7l engines by placing a drain pan underneath the vehicle. First disconnect the Power Steering Hose assembly from the Power Steering Pump before lifting up the vehicle with appropriate safety stands in place. Start by removing retaining bolts that secure both components of the Power Steering Hose assembly bracket then disconnect the retaining bolt connecting the hose assembly to the power steering gear. The Power Steering Hose assembly needs to come off from the power steering gear so technicians can clean both inlet and outlet ports to prevent power steering system element damage and contamination. The power steering gear must be detached from the car before using j 44586 to extract old oil seals. After cleaning the ports repeat the procedure to install new oil seals using j 44586. Secure the power steering gear by reattaching the Power Steering Hose assembly to its bolt and torque it to 12 nm (106 lb in). Proceed with attaching the Power Steering Pump hose by tightening it to 25 nm (18 lb ft) and lower the vehicle before securing the hose assembly retaining bolts to 9 nm (79 lb in). Drain the fluid from the pan before adding the correct amount to the Power Steering Pump reservoir while performing the power steering system bleed procedure.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the Power Steering Hose for the gear inlet and outlet on GMC Canyon? Posted by Customer
    A:
    Start the replacement of the power steering gear inlet and outlet hose by positioning a drain pan beneath the vehicle. First disconnect the Power Steering Hose assembly from the Power Steering Pump then securely place safety stands under the vehicle before raising it upwards. First remove the Power Steering Hose assembly bracket retaining bolts then proceed to disconnect the retaining bolt between the Power Steering Hose assembly and power steering gear. The power steering gear hose should be disconnected from the steering gear followed by vehicle removal while cleaning both ports throughly to protect power steering system components from damage and contamination. The power steering gear oil seal remover/installer (J 44586) allows replacement of power steering gear oil seals when necessary and should be used to remove old oil seals from the power steering gear. Using j 44586 tool again install new oil seals into their appropriate positions by cleaning both inlet and outlet ports beforehand. After guiding the power steering gear into position you should connect its hose assembly to the bolt at the power steering gear then tighten the retaining bolt at 12 n.m (106 lb in). Install the Power Steering Hose assembly clip retaining bolts before tightening them to 9 n.m (79 lb in). To complete installation lower the vehicle stemming the Power Steering Pump connection through a 25 n.m (18 lb ft) torque force. To finish, drain the pan and add correct fluid to the reservoir before completing system bleeding.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be done after tightening the clip retaining bolts for the 2007 Chevrolet Colorado? Posted by Customer
    A:
    Lower the vehicle and connect the power steering hose assembly to the power steering pump, tightening the connection to 25 N.m (18 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Power Steering Hose
    Q:
    What is the final step in the process for the 2009 Chevrolet Colorado? Posted by Customer
    A:
    Remove the drain pan, fill the power steering pump reservoir to the appropriate level, and bleed the power steering system.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Power Steering Hose
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Power Steering Pressure Hose 20934197 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 20934197 Power Steering Pressure Hose is available in the market under the name GM Hydraulic Hose, Power Steering Hose. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 20934197 Power Steering Pressure Hose fits certain Chevrolet Colorado models, as well as GMC Canyon models.
The original GM component designated by manufacturer part number 20934197 maintains top performance when functioning as the Hose, Hydraulic Steering Gear Pressure; Power Steering Hose unit. The component 20934197 is constructed from durable material and its dimensions span 21.4 x 15.6 x 1.6 inches while weighing 0.90 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Hose & Tube Assembly. The part 20934197 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.