Menu
×
Search Bar
Search by Part Number, Part Name, or Vehicle
My Garage
Cart
Help Center Contact Us
Make sure this part fits

GM 25667560
Nameplate

2000-2005 Buick LeSabre

Customer Questions & Expert Answers (8)
GM 25667560 Nameplate
  • Part Description
    Emblem, Instrument Panel
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits

  • 25667560 Nameplate is Ref No. 45 in the diagram below

    2000 Buick LeSabre Nameplate Diagram for 25667560
    The diagram listed above is for your reference. View diagram for your vehicle

    Related Parts for 25667560

  • Vehicle Fitment

    Year Make Model Trim Engine
    2000-2005 Buick LeSabreCustom6 Cyl 3.8 L GAS
    Warning: California's Proposition 65

  • Customer Questions & Expert Answers

    Q:
    Can you help me check if this 25667560 is the right part for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 25667560 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the front emblem/nameplate on Buick LeSabre? Posted by Customer
    A:
    Start by applying tape to the surface where you will install the new emblem/nameplate. Heat up the emblem/nameplate using the J 25070 Heat Gun (J 25070) while applying circular motion to it until it heats for thirty seconds. The panel surface requires an extract of the emblem/nameplate through careful application of a plastic flat-bladed tool. Before attaching the emblem/nameplate check that all adhesive has been eliminated from the surface. for body panels, utilize a 3M(TM) Scotch Bright molding adhesive remover disk (3M(TM) P/N 07502) or an equivalent; The removal of body panel adhesive uses 3M(TM) Scotch Bright molding adhesive remover disk (3M(TM) P/N 07502) or similar alternative while plastic panels need a lint-free cloth soaked in Varnish Makers and Painters (VMP) naphtha or a 50/50 mix of isopropyl alcohol and water. Position the emblem after cleaning the area so the hole faces the fender. The J 25070 (J 25070) device will be used to heat the mounting area to between 27-41 degrees Celsius (80-105 degrees Fahrenheit) if required. The emblem/nameplate requires a temperature of 29-32°C (85-90°F) before pressing it to the surface but you must avoid touching the adhesive side. Take off the protective layer from the emblem/backing then hold the emblem names plate against the fender until the backing presses securely on the mounting location. Make consistent pressure to achieve uniform bonding. Finally, remove the protective tape.
    Posted by ChevyPartsGiant Specialist
    Q:
    What tool should be used to remove the emblem/nameplate for the 2005 Buick LeSabre? Posted by Customer
    A:
    Carefully remove it with a plastic, flat-bladed tool.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What type of tape can be applied to the emblem/nameplate if necessary for the 2000 Buick LeSabre? Posted by Customer
    A:
    Apply double-coated acrylic foam tape such as 3M Super Automotive Attachment Tape (3M 06380 with white backing, 3M 06377 with black backing, or 3M 06382 with gray backing) or an equivalent.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What is the final step after positioning the emblem/nameplate for the 2002 Buick LeSabre? Posted by Customer
    A:
    Remove the protective tape from the mounting surface.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What is the first step to replace the emblem/nameplate on the quarter panel for the 2004 Buick LeSabre? Posted by Customer
    A:
    Apply tape for alignment marks to assist with installation and protect the mounting surface during removal.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What should be done before installing the new emblem/nameplate for the 2003 Buick LeSabre? Posted by Customer
    A:
    Ensure the area is clean and dry, then mark the location for the Le Sabre quarter panel nameplate with tape.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What is the first step to replace the front emblem/nameplate for the 2003 Buick LeSabre? Posted by Customer
    A:
    Protect the mounting surface with tape.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Nameplate 25667560 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 25667560 Nameplate is available in the market under the name GM Emblem. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 25667560 Nameplate fits certain Buick LeSabre models.
The original GM component designated by manufacturer part number 25667560 maintains top performance when functioning as the Emblem, Instrument Panel unit. The component 25667560 is constructed from durable material and its dimensions span 4.1 x 0.6 x 0.4 inches while weighing 0.30 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. The part 25667560 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.