Menu
×
Search Bar
Search by Part Number, Part Name, or Vehicle
My Garage
Cart
Help Center Contact Us
Make sure this part fits

GM 20801143
Striker, Front

2004-2013 GM

Customer Questions & Expert Answers (7)
GM 20801143 Striker, Front
GM 20801143 Striker, Front
GM 20801143 Striker, Front
  • Part Description
    Striker Assembly-Front Side Door Lock
  • Position
    Front
  • Replaces
    10316615
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits

  • 20801143 Striker, Front is Ref No. 10 in the diagram below

    2010 Chevy Corvette Striker, Front Diagram for 20801143
    The diagram listed above is for your reference. View diagram for your vehicle

    Related Parts for 20801143

  • Vehicle Fitment

    Year Make Model Trim Engine
    2004-2009 Cadillac XLRBase, Platinum, V8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
    2005-2013 Chevrolet Corvette427, 427 Limited Edition Z06, Base, Grand Sport, Z06, Z06 Carbon, ZR18 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
    Warning: California's Proposition 65

  • Customer Questions & Expert Answers

    Q:
    Can you help me check if this 20801143 is the right part for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 20801143 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the front door striker on Cadillac XLR? Posted by Customer
    A:
    Start the front Door Striker replacement by elevating the door window before removing its panel. You should remove the large water deflector so you can reach the back of the door. Trace the striker placement on the door frame before unmounting both of the fasteners that secure the striker in the door's internal section. Eventually detach the striker from the door. When installing the striker position it along the door while making sure the latching pin points at the door latch before tightening fasteners onto the striker. The door lock striker's position should be aligned according to the existing marks before tightening its screws to a torque of 25 nm (18 lb ft). When the old marks are not visible to reference you should utilize an assistant to secure the outboard door panel facing directly on the quarter panel and while you tighten the striker fasteners from within the car maintain the door in a steady flush position. Secure the large water deflector behind the door after fastening it into position then replace the door panel front. Check the proper placement of panels while inspecting the door latch function through both manual mode and electric mode activation.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to Ensure Proper Alignment of the Door Striker on Cadillac XLR? Posted by Customer
    A:
    Replacement of the front Door Striker begins through a process where you must raise the door window while removing the door panel and subsequently the large water deflector before reaching the door's rear area. Use a pen to mark the striker spot on the door edge before removing the strikes inside the door while pulling out the striker itself. The installation requires positioning the striker on the door with its latching pin directed at the door latch before securing the fasteners tightly onto the striker. Secure the striker by tightening screws to 25 n.m (18 lb ft) along the previous mark alignment on the fasteners. Tighten the fasteners securing the striker from inside the vehicle while an assistant holds the outer panel against the quarter section then secure the door lock striker screws to 25 n.m (18 lb ft). Reinstallation of the large water deflector along with the door panel should be followed by checking the panel fitment and door latch function through manual and electric door release operation.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the torque specification for tightening the fasteners for the 2004 Cadillac XLR? Posted by Customer
    A:
    Tighten the fasteners to 24 N.m (18 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Striker
    Q:
    How do you remove the striker for the 2006 Cadillac XLR? Posted by Customer
    A:
    Remove the striker fasteners from inside the door and take out the striker.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Striker
    Q:
    What should be done after installing the striker for the 2005 Cadillac XLR? Posted by Customer
    A:
    Reinstall the large water deflector, the door panel, and verify the fit of the panels and the operation of the door latch using both the manual and electric door release.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Striker
    Q:
    How should the fasteners be installed on the striker for the 2008 Cadillac XLR? Posted by Customer
    A:
    Install the fasteners snugly onto the striker.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Striker
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Striker, Front 20801143 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 20801143 Striker, Front is available in the market under the name GM Door Striker. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 20801143 Striker, Front fits certain Chevrolet Corvette models, as well as Cadillac XLR models.
The original GM component designated by manufacturer part number 20801143 maintains top performance when functioning as the Striker Assembly-Front Side Door Lock unit at its Front. The component 20801143 is constructed from durable material and its dimensions span 3.3 x 3.1 x 2.3 inches while weighing 0.60 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Striker, Door Lock Striker. The part 20801143 has available replacement options 10316615. Each vehicle needs 2 units of the part marked as SKU 20801143. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.