Menu
×
Search Bar
Search by Part Number, Part Name, or Vehicle
My Garage
Cart
Help Center Contact Us
Make sure this part fits

GM 25735039
Weatherstrip, Rear

2000-2005 GM

Customer Questions & Expert Answers (9)
GM 25735039 Weatherstrip, Rear
GM 25735039 Weatherstrip, Rear
GM 25735039 Weatherstrip, Rear
  • Part Description
    Weatherstrip Assembly-Rear Compartment Lid
  • Position
    Rear
  • Replaces
    25725053, 25653122, 25723797
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits

  • 25735039 Weatherstrip, Rear is Ref No. 5 in the diagram below

    2003 Buick LeSabre Weatherstrip, Rear Diagram for 25735039
    The diagram listed above is for your reference. View diagram for your vehicle

    Related Parts for 25735039

  • Vehicle Fitment

    Year Make Model Trim Engine
    2000-2005 Buick LeSabreCustom, Limited6 Cyl 3.8 L GAS
    2000-2001 Pontiac BonnevilleSE, SLE, SSEi6 Cyl 3.8 L GAS
    Warning: California's Proposition 65

  • Customer Questions & Expert Answers

    Q:
    Can you help me check if this 25735039 is the right part for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 25735039 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the rear door window Weather Strip on Buick LeSabre? Posted by Customer
    A:
    Start by positioning the rear door window fully down before following steps to remove the door trim panel and door module after taking out the water deflector and the window inner and outer belt sealing strips. Start by removing the rear door window together with the fastener from the division post before proceeding to detach both the rear door stationary window and its window weather strip assembly. You can remove the weather strip and rear door stationary window as an assembly when you pull out the window weather strip from the door frame by grasping the division post. To minimize splaying of the window weather strip you should achieve a tighter fit in the flange mounting area by squeezing together its carrier with thumb and index finger across its length. First prepare and then install the window weather strip together with the stationary window inside the door by seating the stationary window into the frame followed by adding the weather strip into its designated slot. Begin installation by securing the division post fastener to 9 N.m (80 lb in torque). Afterward you can proceed with mounting the rear door window as well as the window outer and inner belt sealing strips, water deflector, door module and lastly the door trim panel.
    Posted by ChevyPartsGiant Specialist
    Q:
    What components need to be removed after moving the window down for the 2000 Buick LeSabre? Posted by Customer
    A:
    The door trim panel, door module, water deflector, window inner belt sealing strip, and window outer belt sealing strip.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What should you ensure about the weatherstrip during installation for the 2002 Buick LeSabre? Posted by Customer
    A:
    Ensure the rubber side of the weatherstrip is outboard of the car, then work downward along the rear edge to install it on the door opening flange, making sure the carrier is fully seated in the corners.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    How do you install the new weatherstrip for the 2003 Buick LeSabre? Posted by Customer
    A:
    Place the weatherstrip over the top of the lid, press it into the rear compartment lid opening.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What should be done after removing the components for the 2005 Buick LeSabre? Posted by Customer
    A:
    Take out the rear door upper auxiliary weatherstrip fasteners (1-7) and carefully peel the auxiliary weatherstrip away from the door header.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    How should the door to door seal be installed for the 2001 Buick LeSabre? Posted by Customer
    A:
    Install the door to door seal on the forward flange of the door header from top to bottom, ensuring the front fastener hole aligns with the plastic nut.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What should be done after installing the window weatherstrip for the 2004 Buick LeSabre? Posted by Customer
    A:
    Install the window channel fasteners, tightening them to 9 N.m (80 lb in), followed by the door window, outside rearview mirror, window outer belt sealing strip, window inner belt sealing strip, water deflector, door module, and finally, the door trim panel.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What is the first step to replace the front door weatherstrip for the 2004 Buick LeSabre? Posted by Customer
    A:
    First, remove the sill plate.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Weatherstrip, Rear 25735039 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 25735039 Weatherstrip, Rear is available in the market under the name GM Weather Strip. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 25735039 Weatherstrip, Rear fits certain Buick LeSabre models, as well as Pontiac Bonneville models.
The original GM component designated by manufacturer part number 25735039 maintains top performance when functioning as the Weatherstrip Assembly-Rear Compartment Lid unit at its Rear. The component 25735039 is constructed from durable material and its dimensions span 18.7 x 17.9 x 6.2 inches while weighing 2.20 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Weatherstrip, Rear Compartment Lid. The part 25735039 has available replacement options 25725053, 25653122, 25723797. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.