How to replace the rear brake calipers on 2002 Chevrolet Suburban 2500?

First, check the fluid level in the brake master cylinder reservoir, then, to change the rear brake caliper. If it is in the middle between the maximum-full point and minimum allowable level, none should be removed but if it is above lower it to the midway level. Lift up the vehicle to remove the tire and wheel assembly. Compress the brake caliper pistons with a large c-clamp over the top of the caliper housing to the back of the outboard pad, clamping until the pistons are fully compressed. Make good the brake hose end and at the exposed brake pipe fitting fit a rubber cap or plug so that the hose will not lose any fluid and be dirtied. Remove the brake hose to caliper bolt and throw out the 2 copper brake hose gaskets, possibly stuck to the caliper housing or hose end. Then, you have to remove the brake caliper guide pin bolts and unbolt the brake caliper from the car, whereby inspect the caliper assembly. In the case of installation of new brake pads, make use of a c-clamp to compress the pistons to the bottom of the caliper bores, protecting them using the old Brake Pad, metal plate or a wooden block. Lift the internal edge of the caliper boots by each piston with a small flat bladed tool to release any then trapped air so that the boots are below the face of the pistons. Mount onto the mounting bracket and gently remove any original adhesive patch, followed by cleaning the bolt threads using brake parts cleaner then applying thread locker gm p/n 12345493 (Canadian P/N 10953488) to the threads. Mount the brake caliper mounting bolts and tighten the brake caliper' guide pin bolts to 42 nm (31 ft. Lbs.). Unfit the brake hose fitting rubber cap/plug fitted on the hose, fitting two new copper brake hoses gaskets, and fitting a new brake hose on the caliper by tightening the brake hose to the fitting of the caliper bolt to 40 nm (30 ft. Lbs.). Drain the hydraulic brake system, put the tire and wheel assembly back, lower the vehicle, and top-up the master cylinder reservoir to the required level using clean brake fluid.

OEM 2002 Chevrolet Suburban 2500 Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Brake Calipers found

View related parts
2002 Chevrolet Suburban 2500 Caliper
Part Number: 19331021
$170.23 MSRP: $328.77
You Save: $158.54 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Rear
- Replaces: 18040101, 25848000
- Item Weight: 11.90 Pounds
- Item Dimensions: 7.2 x 4.1 x 12.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19331021
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Suburban 2500 Submodels:
- Base, LS, LT, LTZ | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
2002 Chevrolet Suburban 2500 Caliper
Part Number: 19331022
$171.88 MSRP: $331.97
You Save: $160.09 (49%)
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Rear
- Replaces: 25848001, 18040100
- Item Weight: 11.80 Pounds
- Item Dimensions: 13.0 x 7.1 x 4.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19331022
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Suburban 2500 Submodels:
- Base, LS, LT, LTZ | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
2002 Chevrolet Suburban 2500 Caliper, Front Driver Side
Part Number: 84394384
$107.66 MSRP: $208.96
You Save: $101.30 (49%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaced by: 87859910
- Item Weight: 15.50 Pounds
- Item Dimensions: 8.4 x 5.3 x 14.4 inches
- Condition: New
- SKU: 84394384
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Suburban 2500 Submodels:
- Base, LS, LT, LTZ | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
2002 Chevrolet Suburban 2500 Caliper, Passenger Side
Part Number: 84803425
$135.01 MSRP: $251.95
You Save: $116.94 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket); Caliper, Wheel Brake Cylinder/Caliper
- Position: Passenger Side
- Replaced by: 87859911
- Condition: New
- SKU: 84803425
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following 2002 Chevrolet Suburban 2500 Submodels:
- Base, LS, LT, LTZ | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
2002 Chevrolet Suburban 2500 Caliper, Driver Side
Part Number: 18040100
$171.88 MSRP: $331.97
You Save: $160.09 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Driver Side
- Replaced by: 19331022
- Item Weight: 11.80 Pounds
- Item Dimensions: 12.8 x 7.2 x 4.0 inches
- Condition: New
- SKU: 18040100
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Suburban 2500 Submodels:
- Base, LS, LT, LTZ | 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
2002 Chevrolet Suburban 2500 Caliper, Front Passenger Side
Part Number: 84394392
$185.79 MSRP: $343.75
You Save: $157.96 (46%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Replaces: 25846389, 18046220
- Item Weight: 15.70 Pounds
- Item Dimensions: 14.8 x 8.5 x 5.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 84394392
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Suburban 2500 Submodels:
- Base, LS, LT | 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
2002 Chevrolet Suburban 2500 Caliper, Passenger Side
Part Number: 18043521
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Passenger Side
- Item Weight: 8.50 Pounds
- Item Dimensions: 7.9 x 9.2 x 6.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18043521
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Suburban 2500 Submodels:
- Base, LS, LT | 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
2002 Chevrolet Suburban 2500 Caliper, Driver Side
Part Number: 18043520
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Driver Side
- Item Weight: 5.00 Pounds
- Item Dimensions: 9.2 x 8.3 x 6.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18043520
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Suburban 2500 Submodels:
- Base, LS, LT | 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
2002 Chevrolet Suburban 2500 Caliper, Front Driver Side
Part Number: 84394391
$190.26 MSRP: $341.26
You Save: $151.00 (45%)
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaces: 18046219, 25846388
- Item Weight: 15.90 Pounds
- Item Dimensions: 14.8 x 8.5 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 84394391
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2002 Chevrolet Suburban 2500 Submodels:
- Base, LS, LT | 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS

2002 Chevrolet Suburban 2500 Brake Calipers

With a comprehensive array of OEM 2002 Chevrolet Suburban 2500 Brake Calipers, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2002 Chevrolet Suburban 2500 Brake Calipers are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2002 Chevrolet Suburban 2500 Parts Questions & Experts Answers

Q: How to replace the rear brake calipers on 2002 Chevrolet Suburban 2500?
A: First, check the fluid level in the brake master cylinder reservoir, then, to change the rear brake caliper. If it is in the middle between the maximum-full point and minimum allowable level, none should be removed but if it is above lower it to the midway level. Lift up the vehicle to remove the tire and wheel assembly. Compress the brake caliper pistons with a large c-clamp over the top of the caliper housing to the back of the outboard pad, clamping until the pistons are fully compressed. Make good the brake hose end and at the exposed brake pipe fitting fit a rubber cap or plug so that the hose will not lose any fluid and be dirtied. Remove the brake hose to caliper bolt and throw out the 2 copper brake hose gaskets, possibly stuck to the caliper housing or hose end. Then, you have to remove the brake caliper guide pin bolts and unbolt the brake caliper from the car, whereby inspect the caliper assembly. In the case of installation of new brake pads, make use of a c-clamp to compress the pistons to the bottom of the caliper bores, protecting them using the old Brake Pad, metal plate or a wooden block. Lift the internal edge of the caliper boots by each piston with a small flat bladed tool to release any then trapped air so that the boots are below the face of the pistons. Mount onto the mounting bracket and gently remove any original adhesive patch, followed by cleaning the bolt threads using brake parts cleaner then applying thread locker gm p/n 12345493 (Canadian P/N 10953488) to the threads. Mount the brake caliper mounting bolts and tighten the brake caliper' guide pin bolts to 42 nm (31 ft. Lbs.). Unfit the brake hose fitting rubber cap/plug fitted on the hose, fitting two new copper brake hoses gaskets, and fitting a new brake hose on the caliper by tightening the brake hose to the fitting of the caliper bolt to 40 nm (30 ft. Lbs.). Drain the hydraulic brake system, put the tire and wheel assembly back, lower the vehicle, and top-up the master cylinder reservoir to the required level using clean brake fluid.

Related 2002 Chevrolet Suburban 2500 Parts

Alternate Year Models

2001 Chevrolet Suburban 2500 Brake Calipers 2003 Chevrolet Suburban 2500 Brake Calipers