How to overhaul the rear brake calipers on 2006 Chevrolet Monte Carlo?

For safe brake caliper overhaul you need to remove the unit while watching out for blowing air pressure to avoid fingers near the pistons which could pop out forcibly and harm you. Insert clean pads inside the caliper before you blow out the pistons through the fluid intake hole with low air pressure. You must first remove the caliper housing retaining ring before taking out the dust boot piston seal. A small wooden or plastic tool can help you remove and throw away the piston seal from the caliper opening. Use denatured alcohol to clean all surfaces of the Brake Caliper Piston bore, seal counterbore, and caliper piston but exclude abrasive materials. After cleaning the caliper bore with air filter and non-lubricated air blow-dry the parts. Inspect for detrimental factors such as cracks, scoring, rust, and corrosion; if only minimal rust exists attempt to smooth it by sanding but replace components if issues persist. Replace the entire caliper unit when you discover damage on its piston. Put delco supreme 11(R) brake fluid gm p/n 12377967 (Canadian P/N 992667) or equivalent from a sealed container onto the new piston seal then insert it into the caliper bore. Place thin layers of brake fluid onto caliper piston top before inserting its lower part into the bore. Push the new piston dust boot seal over the caliper piston while pressing the piston all the way down to make sure the seal hollows out properly in the caliper counterbore. Place the retaining ring on the dust boot then put on the bleeder valve and cap before securing the valve. Finally fit the caliper back to its place.

OEM 2006 Chevrolet Monte Carlo Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Brake Calipers found

View related parts
2006 Chevrolet Monte Carlo Caliper
Part Number: 88965667
$76.17 MSRP: $231.41
You Save: $155.24 (68%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Rear Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear
- Replaces: 18029936
- Item Weight: 4.10 Pounds
- Item Dimensions: 8.1 x 6.2 x 3.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 88965667
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Monte Carlo Submodels:
- LS, LS Competition, LS Sport, LT, LTZ, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
2006 Chevrolet Monte Carlo Caliper, Front Passenger Side
Part Number: 25983765
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Replaces: 15251789
- Item Weight: 6.40 Pounds
- Item Dimensions: 10.1 x 7.4 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 25983765
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Monte Carlo Submodels:
- LS, LT, LTZ, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
2006 Chevrolet Monte Carlo Caliper, Front Driver Side
Part Number: 25983764
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaces: 15251788
- Item Weight: 8.50 Pounds
- Item Dimensions: 8.2 x 6.2 x 10.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 25983764
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Monte Carlo Submodels:
- LS, LT, LTZ, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
2006 Chevrolet Monte Carlo Caliper Piston
Part Number: 88967227
Product Specifications
- Other Name: Caliper Kit, Rear Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Brake Caliper Piston; Caliper Overhaul Kit
- Position: Rear
- Item Weight: 0.30 Pounds
- Item Dimensions: 7.9 x 9.2 x 6.5 inches
- Condition: New
- SKU: 88967227
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Monte Carlo Submodels:
- LS, LT, LTZ, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
2006 Chevrolet Monte Carlo Caliper
Part Number: 88965666
Product Specifications
- Other Name: Caliper Assembly, Rear Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear
- Replaces: 18029935
- Item Weight: 4.10 Pounds
- Item Dimensions: 8.2 x 6.3 x 3.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 88965666
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Monte Carlo Submodels:
- LS, LS Competition, LS Sport, LT, LTZ, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS

2006 Chevrolet Monte Carlo Brake Calipers

With a comprehensive array of OEM 2006 Chevrolet Monte Carlo Brake Calipers, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2006 Chevrolet Monte Carlo Brake Calipers are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2006 Chevrolet Monte Carlo Parts Questions & Experts Answers

Q: How to overhaul the rear brake calipers on 2006 Chevrolet Monte Carlo?
A: For safe brake caliper overhaul you need to remove the unit while watching out for blowing air pressure to avoid fingers near the pistons which could pop out forcibly and harm you. Insert clean pads inside the caliper before you blow out the pistons through the fluid intake hole with low air pressure. You must first remove the caliper housing retaining ring before taking out the dust boot piston seal. A small wooden or plastic tool can help you remove and throw away the piston seal from the caliper opening. Use denatured alcohol to clean all surfaces of the Brake Caliper Piston bore, seal counterbore, and caliper piston but exclude abrasive materials. After cleaning the caliper bore with air filter and non-lubricated air blow-dry the parts. Inspect for detrimental factors such as cracks, scoring, rust, and corrosion; if only minimal rust exists attempt to smooth it by sanding but replace components if issues persist. Replace the entire caliper unit when you discover damage on its piston. Put delco supreme 11(R) brake fluid gm p/n 12377967 (Canadian P/N 992667) or equivalent from a sealed container onto the new piston seal then insert it into the caliper bore. Place thin layers of brake fluid onto caliper piston top before inserting its lower part into the bore. Push the new piston dust boot seal over the caliper piston while pressing the piston all the way down to make sure the seal hollows out properly in the caliper counterbore. Place the retaining ring on the dust boot then put on the bleeder valve and cap before securing the valve. Finally fit the caliper back to its place.