How to replace the steering knuckle on 2008 Chevrolet Colorado?

Firstly, lift and support the vehicle to replace the Steering Knuckle. Take off the tire and wheel assembly and then you should lift up the lower Control Arm with a suitable jack. It is important to lift the brake caliper assembly from the unit without having to dismount the mounting bracket after which it is supported on mechanics wire. If the car has a 4wd section, unscrew the front wheel drive shaft from the Steering Knuckle. Following, disconnect the speed sensor wiring harness from the retaining clips of the upper Control Arm and the frame and disconnect the outer Tie Rod End of the knuckle. Remove the upper Ball Joint and the knuckle and then follow it with the lower Ball Joint. Remove the knuckle from upper and lower Control Arm and pull off the Wheel Hub and bearing assembly from the knuckle. For installation, one should begin by putting the Wheel Hub and bearing assembly on the knuckle and then install lower Control Arm /ball joint into the knuckle. In case the vehicle is equipped with 4wd, place the wheel drive shaft into the knuckle. Following that, insert the upper Control Arm/ball joint in the knuckle and then the outer Tie Rod End. Refasten the speed wire harness into the retaining clips then bolt in the brake caliper mounting bracket. Tighten the wheel drive shaft retaining nut to specifications, remove the support from the lower Control Arm before venturing the installation of the tire and wheel before lowering the vehicle.

OEM 2008 Chevrolet Colorado Steering Knuckle

Front Steering Knuckle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Steering Knuckles found

View related parts
2008 Chevrolet Colorado Knuckle, Passenger Side
Part Number: 19303833
Product Specifications
- Other Name: Knuckle, Steering
- Position: Passenger Side
- Replaces: 15178871
- Item Weight: 9.90 Pounds
- Item Dimensions: 14.2 x 10.3 x 6.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19303833
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Colorado Submodels:
- Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
2008 Chevrolet Colorado Knuckle, Driver Side
Part Number: 19303836
Product Specifications
- Other Name: Knuckle, Steering
- Position: Driver Side
- Replaces: 15184896
- Item Weight: 10.10 Pounds
- Item Dimensions: 11.6 x 11.1 x 6.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19303836
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Colorado Submodels:
- Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
2008 Chevrolet Colorado Knuckle, Passenger Side
Part Number: 19303835
Product Specifications
- Other Name: Knuckle, Steering
- Position: Passenger Side
- Replaces: 15184895
- Item Weight: 11.40 Pounds
- Item Dimensions: 11.4 x 11.4 x 6.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19303835
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Colorado Submodels:
- Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
2008 Chevrolet Colorado Knuckle, Driver Side
Part Number: 19303834
$257.84 MSRP: $405.70
You Save: $147.86 (37%)
Product Specifications
- Other Name: Knuckle, Steering
- Position: Driver Side
- Replaces: 15178872
- Item Weight: 9.40 Pounds
- Item Dimensions: 13.4 x 10.4 x 4.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19303834
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Colorado Submodels:
- Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
2008 Chevrolet Colorado Knuckle, Driver Side
Part Number: 15178874
Product Specifications
- Other Name: Knuckle, Steering
- Position: Driver Side
- Item Weight: 9.70 Pounds
- Item Dimensions: 11.9 x 9.9 x 6.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15178874
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Colorado Submodels:
- Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
2008 Chevrolet Colorado Knuckle, Passenger Side
Part Number: 15178873
Product Specifications
- Other Name: Knuckle, Steering
- Position: Passenger Side
- Item Weight: 9.70 Pounds
- Item Dimensions: 12.4 x 9.9 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15178873
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Colorado Submodels:
- Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS

2008 Chevrolet Colorado Steering Knuckle

With a comprehensive array of OEM 2008 Chevrolet Colorado Steering Knuckle, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2008 Chevrolet Colorado Steering Knuckle are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2008 Chevrolet Colorado Steering Knuckle Parts Questions & Experts Answers

Q: How to replace the steering knuckle on 2008 Chevrolet Colorado?
A: Firstly, lift and support the vehicle to replace the Steering Knuckle. Take off the tire and wheel assembly and then you should lift up the lower Control Arm with a suitable jack. It is important to lift the brake caliper assembly from the unit without having to dismount the mounting bracket after which it is supported on mechanics wire. If the car has a 4wd section, unscrew the front wheel drive shaft from the Steering Knuckle. Following, disconnect the speed sensor wiring harness from the retaining clips of the upper Control Arm and the frame and disconnect the outer Tie Rod End of the knuckle. Remove the upper Ball Joint and the knuckle and then follow it with the lower Ball Joint. Remove the knuckle from upper and lower Control Arm and pull off the Wheel Hub and bearing assembly from the knuckle. For installation, one should begin by putting the Wheel Hub and bearing assembly on the knuckle and then install lower Control Arm /ball joint into the knuckle. In case the vehicle is equipped with 4wd, place the wheel drive shaft into the knuckle. Following that, insert the upper Control Arm/ball joint in the knuckle and then the outer Tie Rod End. Refasten the speed wire harness into the retaining clips then bolt in the brake caliper mounting bracket. Tighten the wheel drive shaft retaining nut to specifications, remove the support from the lower Control Arm before venturing the installation of the tire and wheel before lowering the vehicle.