How to replace the front A/C Hose in the HVAC system on 2009 Buick Enclave?

Using the halogen leak detector (J 39400-A) designers should start by recovering the refrigerant found in the hvac system. The replacement process starts with remover of the sight shield covering the injector followed by removal of the right engine mount strut. To begin the restructuring process remove the underhood electrical center along with its bracket before readjusting the wiring harness installation. The replacement of the liquid line starts with unbolting the line from the A/C Condenser and then separating the liquid line from the condenser. Unfasten both the txv tube retainer nut and the liquid line to auxiliary tube nut. First disconnect the txv components at the plenum panel through unclamping the liquid line from the right inner frame rail and plenum panel. The right liquid line bracket bolt at the upper tie bar support must be removed before you take out the liquid line along with the discharge line sealing washer. New sealing washers should be installed onto the liquid line before the installer attaches it to the txv at the plenum panel then screws in the liquid line to txv nut while using metric torque specifications of 9 nm (80 lb in). First install the liquid line to the auxiliary evaporator tube before tightening the nut to 9 nm (80lb in) torque. After that connect the liquid line to the condenser with a nut that requires 9 nm (80 lb in) torque. First secure the liquid line bracket bolt to the upper tie bar support by torquing it up to 9 nm at 80 lb in and next torques the liquid line bracket nuts along the frame rail and plenum panel at 4 nm (35 lb in). After installation of the underhood electrical center bracket and the underhood electrical center proceed to install both the front bumper upper facia support and the right engine mount strut. End your repair by putting back the injector sight shield. Empty the refrigerant system then refuel it before testing all fittings for air leaks with the halogen leak detector (J 39400-A).

OEM 2009 Buick Enclave A/C Hose

Air Conditioning Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 A/C Hoses found

View related parts
2009 Buick Enclave Rear A/C Tube Part Number: 23199274
$316.40 MSRP: $936.57
You Save: $620.17 (67%)
ADD TO CART
Product Specifications
- Other Name: Tube, Air Conditioner Refrigerant (All Metal); A/C Refrigerant Liquid Hose; A/C Hose
- Replaces: 15951309, 20882828, 25862086, 25892086
- Item Weight: 9.40 Pounds
- Item Dimensions: 82.4 x 22.3 x 12.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 23199274
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Buick Enclave Submodels:
- Base, Convenience, CX, CXL, Leather, Premium | 6 Cyl 3.6 L GAS
View related parts
2009 Buick Enclave Discharge Hose Part Number: 19356341
$66.90 MSRP: $137.48
You Save: $70.58 (52%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Air Conditioner Compressor; A/C Refrigerant Liquid Hose; A/C Hose; Pressure Hose; Compressor & Condenser Hose; Hose, A/C Compressor Suction And Discharge; Hose, A/C Compressor
- Replaces: 15926077, 22757062, 22744629
- Item Weight: 0.80 Pounds
- Item Dimensions: 12.7 x 1.1 x 1.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19356341
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Buick Enclave Submodels:
- Base, CX, CXL | 6 Cyl 3.6 L GAS
View related parts
2009 Buick Enclave A/C Tube Part Number: 22875372
$178.16 MSRP: $366.11
You Save: $187.95 (52%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube, Air Conditioner Evaporator; A/C Refrigerant Liquid Hose; A/C Hose; Tube, A/C Refrigerant (All Metal); Tube, A/C Evaporator
- Replaces: 10353015, 20821215, 22792489
- Item Weight: 4.40 Pounds
- Item Dimensions: 38.1 x 22.2 x 16.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 22875372
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Buick Enclave Submodels:
- Base, CX, CXL | 6 Cyl 3.6 L GAS
View related parts
2009 Buick Enclave Compressor Hose Part Number: 19433113
$195.56 MSRP: $350.79
You Save: $155.23 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, A/C Compressor & Evaporator; Suction Hose; Front Suction Hose; Hose, A/C Refrigerant (Metal And Rubber Sections); Hose, A/C Compressor And Condenser
- Replaces: 20864505, 20757020
- Condition: New
- SKU: 19433113
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following 2009 Buick Enclave Submodels:
- Base, CX, CXL | 6 Cyl 3.6 L GAS
View related parts
2009 Buick Enclave Suction Hose Part Number: 20821216
$133.89 MSRP: $242.34
You Save: $108.45 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube, Air Conditioner Refrigerant (All Metal); A/C Refrigerant Liquid Hose; A/C Hose; Rear Suction Hose; Rear Suction Tube; Tube, A/C Refrigerant (All Metal); Tube, A/C Evaporator
- Replaces: 25795291
- Item Weight: 1.00 Pounds
- Item Dimensions: 15.2 x 10.6 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 20821216
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Buick Enclave Submodels:
- Base, CX, CXL | 6 Cyl 3.6 L GAS
View related parts
2009 Buick Enclave Tube Part Number: 25791601
$20.39 MSRP: $38.04
You Save: $17.65 (47%)
ADD TO CART
Product Specifications
- Other Name: Hose, Air Conditioner Electric Temperature And Motor Control; A/C Refrigerant Liquid Hose; A/C Hose; Hose; Hose, A/C Electric Temperature And Motor Control
- Replaced by: 23172046
- Item Weight: 0.50 Pounds
- Item Dimensions: 18.5 x 18.1 x 7.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 25791601
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Buick Enclave Submodels:
- Base, CX, CXL | 6 Cyl 3.6 L GAS
View related parts
2009 Buick Enclave Drain Hose Part Number: 25791603
Product Specifications
- Other Name: Hose, Air Conditioner Evaporator Core Housing; Hose, A/C Evaporator Core Housing; Hose, A/C Evaporator
- Item Weight: 0.40 Pounds
- Item Dimensions: 14.2 x 0.8 x 0.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 25791603
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Buick Enclave Submodels:
- Base, Convenience, CX, CXL, Leather, Premium | 6 Cyl 3.6 L GAS

2009 Buick Enclave A/C Hose

With a comprehensive array of OEM 2009 Buick Enclave A/C Hose, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2009 Buick Enclave A/C Hose are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2009 Buick Enclave A/C Hose Parts and Q&A

Q: How to replace the front A/C Hose in the HVAC system on 2009 Buick Enclave?
A: Using the halogen leak detector (J 39400-A) designers should start by recovering the refrigerant found in the hvac system. The replacement process starts with remover of the sight shield covering the injector followed by removal of the right engine mount strut. To begin the restructuring process remove the underhood electrical center along with its bracket before readjusting the wiring harness installation. The replacement of the liquid line starts with unbolting the line from the A/C Condenser and then separating the liquid line from the condenser. Unfasten both the txv tube retainer nut and the liquid line to auxiliary tube nut. First disconnect the txv components at the plenum panel through unclamping the liquid line from the right inner frame rail and plenum panel. The right liquid line bracket bolt at the upper tie bar support must be removed before you take out the liquid line along with the discharge line sealing washer. New sealing washers should be installed onto the liquid line before the installer attaches it to the txv at the plenum panel then screws in the liquid line to txv nut while using metric torque specifications of 9 nm (80 lb in). First install the liquid line to the auxiliary evaporator tube before tightening the nut to 9 nm (80lb in) torque. After that connect the liquid line to the condenser with a nut that requires 9 nm (80 lb in) torque. First secure the liquid line bracket bolt to the upper tie bar support by torquing it up to 9 nm at 80 lb in and next torques the liquid line bracket nuts along the frame rail and plenum panel at 4 nm (35 lb in). After installation of the underhood electrical center bracket and the underhood electrical center proceed to install both the front bumper upper facia support and the right engine mount strut. End your repair by putting back the injector sight shield. Empty the refrigerant system then refuel it before testing all fittings for air leaks with the halogen leak detector (J 39400-A).