How to replace the axle shaft on Cadillac Eldorado?

Releasing the axle shafts begins by securely raising the vehicle then securing it. Start by removing the wheel followed by tire removal then loosen the stabilizer shaft link assembly bolt as needed. When removing the ball joint assembly use a pickle fork or wedge type tool to carefully separate the parts while protecting the bushing and seal. The j 36226 tool should be used for joint loosening purposes while right axle replacement requires wheel left-turn rotation and vice versa for left axle work. During left axle axle removal turn the steering wheel right to achieve alignment. Separate the joint by inserting a pry bar between the suspension support and the lower control arm. Put a drift or screwdriver through the caliper and rotor to stop their movement. Then take off the hub nut. Use tool j 28733-b to disconnect the hub from the axle but maintain partial hub installation to shield thread integrity before moving the strut and knuckle towards the rear of the vehicle. At this time avoid stretching the Axle Shaft. Lock up the drive axle to the transaxle using j 33008-a and j 2619-01. Metal corrosion on the tripot housing must be examined at the transmission seal interface and smoothness can be achieved by using 320 grit emery cloth sanding. Apply clean transmission fluid to the tripot housing then push the axle into the transaxle before confirming axle position by grasping the inner joint housing. Use a new hub nut to secure the drive axle into the hub and bearing before using a drift or screwdriver to stop rotor movement then tighten the hub nut to 145 nm (107 ft. Lbs.). Drive the ball joint into the knuckle by tightening the ball joint nut to 10 nm (88 inch lbs.) afterward rotate the joint by 120 degrees until it reaches 55 nm (41 ft. Lbs.). Tighten the stabilizer shaft link assembly's nut to specifications at 17 nm (13 ft. Lbs.) after inserting the cotter pin and making required slot adjustments in the nut. Put the wheel and tire on before lowering the vehicle to the ground.

OEM Cadillac Eldorado Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Axle Shafts found

View related parts
Cadillac Eldorado Axle Shaft Assembly, Front Passenger Side Part Number: 26078539
$35.71 MSRP: $597.64
You Save: $561.93 (95%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Axle Assembly; Shaft Kit, Front Wheel Drive Axle
- Position: Front Passenger Side
- Replaces: 26017179
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1989-1990 Cadillac Eldorado | Base, Biarritz, Touring | 8 Cyl 4.5 L GAS
View related parts
Cadillac Eldorado Axle Assembly Part Number: 26017179
$379.81 MSRP: $597.64
You Save: $217.83 (37%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly; Axle Shaft
- Replaced by: 26078539
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1989 Cadillac Eldorado | Base, Biarritz | 8 Cyl 4.5 L GAS
View related parts
Cadillac Eldorado Axle Shaft, Passenger Side Part Number: 7848444
$163.74 MSRP: $305.53
You Save: $141.79 (47%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Damper & (Painted); Shaft; Shaft, Front Wheel Drive Axle
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1987 Cadillac Eldorado | Base, Biarritz | 8 Cyl 4.1 L GAS
View related parts
Cadillac Eldorado Axle Shaft, Driver Side Part Number: 7846169
$50.66 MSRP: $90.46
You Save: $39.80 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Front Wheel Drive; Axle Shafts; Shaft; Shaft, Front Wheel Drive Axle
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Cadillac Eldorado | Base, Biarritz, Spring Edition, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Eldorado Axle Shaft Part Number: 26074876
Product Specifications
- Other Name: Shaft
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999 Cadillac Eldorado | ESC, ETC | 8 Cyl 4.6 L GAS
View related parts
Cadillac Eldorado Axle Shaft Assembly, Passenger Side Part Number: 26015543
Product Specifications
- Other Name: Shaft Assembly; Axle Shaft; Axle Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1989 Cadillac Eldorado | Base, Biarritz | 8 Cyl 4.5 L GAS
View related parts
Cadillac Eldorado Axle Shaft Assembly, Driver Side Part Number: 26009539
Product Specifications
- Other Name: Half Shift; Axle Shaft; Axle Assembly
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1989 Cadillac Eldorado | Base, Biarritz | 8 Cyl 4.5 L GAS
View related parts
Cadillac Eldorado Axle Shaft, Front Passenger Side Part Number: 26006856
Product Specifications
- Other Name: Shaft, Front Wheel Drive Axle; Shaft
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1990 Cadillac Eldorado | Base, Biarritz, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS
View related parts
Cadillac Eldorado Axle Shaft, Front Passenger Side Part Number: 26003284
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; Axle Shaft Assembly; Axle Assembly; Shaft Assembly; Shaft Kit, Front Wheel Drive Axle
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1988 Cadillac Eldorado | Base, Biarritz | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS
View related parts
Cadillac Eldorado Axle Shaft, Front Driver Side Part Number: 26000329
Product Specifications
- Other Name: Shaft Kit-Front Wheel Drive; Axle Shaft Assembly; Axle Assembly; Shaft Assembly; Shaft Kit, Front Wheel Drive Axle; Axle Kit, Front Wheel Drive Axle
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1989 Cadillac Eldorado | Base, Biarritz | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS
View related parts
Cadillac Eldorado Axle Shaft Assembly, Front Part Number: 26078585
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Axle Assembly; Axle; Shaft Kit, Front Wheel Drive Axle
- Position: Front
- Replaces: 26027053, 26021720, 26035210
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 Cadillac Eldorado | Base, Sport, Touring | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Eldorado Axle Shaft Assembly, Front Passenger Side Part Number: 26078583
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Axle Assembly; Shaft Kit, Front Wheel Drive Axle
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991 Cadillac Eldorado | Base, Biarritz, Spring Edition, Touring | 8 Cyl 4.9 L GAS
View related parts
Cadillac Eldorado Axle Shaft Assembly, Front Driver Side Part Number: 26078505
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Axle Assembly; Shaft Kit, Front Wheel Drive Axle
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1989-1991 Cadillac Eldorado | Base, Biarritz, Spring Edition, Touring | 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Eldorado Axle Shaft Assembly, Front Part Number: 26078251
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Axle Assembly; Axle; Shaft Kit, Front Wheel Drive Axle
- Position: Front
- Replaces: 26021721, 26027054
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 Cadillac Eldorado | Base, Sport, Touring | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Eldorado Axle Assembly, Front Part Number: 26075604
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; Axle Shaft; Axle; Shaft Kit, Front Wheel Drive Axle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2002 Cadillac Eldorado | ESC, ETC | 8 Cyl 4.6 L GAS
View related parts
Cadillac Eldorado Axle Shaft Assembly, Front Part Number: 26075423
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; Axle Shaft; Axle Assembly; Axle; Shaft Kit, Front Wheel Drive Axle
- Position: Front
- Replaces: 26030759
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1999 Cadillac Eldorado | Base, ESC, ETC, Sport, Touring | 8 Cyl 4.6 L GAS

Cadillac Eldorado Axle Shaft

Want to cut long-term maintenance and repair costs? Choose OEM Axle Shaft. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Cadillac Eldorado parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Cadillac Eldorado Axle Shaft includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

An Axle Shaft of Cadillac Eldorado automobiles is a part that transmits power from the differential to the drive wheels, and designed for their independent rotation to increase tractive force. These steel shafts include; solid axle for trucks and older models of vehicles as well as the halfshaft for the vehicles with independent suspensions. Assembly of a Land Cruiser starts with a solid axle that contains the differential and ax shafts and the half assembly includes splined shaft for the connection with the CV joint and the wheel hub. Sustenance may be necessary because of worn out CV joints or axle bearings; this causes noise and vibration. In conclusion, the Axle Shaft is a vital component that holds the wheels in place and transfers torque while at the same time bearing the weight of the particular Cadillac Eldorado car model.

Cadillac Eldorado Axle Shaft Parts and Q&A

Axle Assembly, Front
26075604
Q: How to replace the axle shaft on Cadillac Eldorado?
A:
Releasing the axle shafts begins by securely raising the vehicle then securing it. Start by removing the wheel followed by tire removal then loosen the stabilizer shaft link assembly bolt as needed. When removing the ball joint assembly use a pickle fork or wedge type tool to carefully separate the parts while protecting the bushing and seal. The j 36226 tool should be used for joint loosening purposes while right axle replacement requires wheel left-turn rotation and vice versa for left axle work. During left axle axle removal turn the steering wheel right to achieve alignment. Separate the joint by inserting a pry bar between the suspension support and the lower control arm. Put a drift or screwdriver through the caliper and rotor to stop their movement. Then take off the hub nut. Use tool j 28733-b to disconnect the hub from the axle but maintain partial hub installation to shield thread integrity before moving the strut and knuckle towards the rear of the vehicle. At this time avoid stretching the Axle Shaft. Lock up the drive axle to the transaxle using j 33008-a and j 2619-01. Metal corrosion on the tripot housing must be examined at the transmission seal interface and smoothness can be achieved by using 320 grit emery cloth sanding. Apply clean transmission fluid to the tripot housing then push the axle into the transaxle before confirming axle position by grasping the inner joint housing. Use a new hub nut to secure the drive axle into the hub and bearing before using a drift or screwdriver to stop rotor movement then tighten the hub nut to 145 nm (107 ft. Lbs.). Drive the ball joint into the knuckle by tightening the ball joint nut to 10 nm (88 inch lbs.) afterward rotate the joint by 120 degrees until it reaches 55 nm (41 ft. Lbs.). Tighten the stabilizer shaft link assembly's nut to specifications at 17 nm (13 ft. Lbs.) after inserting the cotter pin and making required slot adjustments in the nut. Put the wheel and tire on before lowering the vehicle to the ground.