What tools are required to service and repair the steering knuckle on Cadillac Eldorado?

Service and repairs of the Steering Knuckle require three essential tools: ball stud separator (J36226) ball stud nut wrench (J35551) and tie rod remover (J24319-B). Three necessary tools include ball stud separator (J36226), ball stud nut wrench (J35551), and tie rod remover (J24319-B). Start with wheel lifting and vehicle support followed by tire removal and moving onward to Wheel Bearing assembly and hub replacement. Disconnect the outer tie rod at the Steering Knuckle before removing the road sensing suspension sensor link. You must remove both the lower Ball Joint cotter pin alongside the retaining nut. Apply the ball stud separator (J36226) on the Steering Knuckle to detach it from the lower Control Arm before unfastening the strut to Steering Knuckle retaining nuts and bolts. Install the new Steering Knuckle after which you should attach the lower Ball Joint to this knuckle's assembly. Secure the bottom part of the suspension strut to the Steering Knuckle through retaining bolts and nuts while following manufacturer-recommended fastener torque values. Tighten the lower Ball Joint retaining nut to 10 nm (7 inch lbs.) but continue tightening an additional 150 degrees (2 1/2 flats) in addition to a 60-degree alignment for the cotter pin. Insert a fresh cotter pin afterward you must link the road sensing suspension position sensor to the lower Control Arm followed by reconnecting the outer Tie Rod End to the Steering Knuckle. Reinstall the Wheel Bearing and hub assembly as well as the tire and wheel before lowering the vehicle down.

How to replace the steering knuckle on Cadillac Eldorado?

The Steering Knuckle replacement process begins with vehicle support followed by wheel and tire separation then elimination of the bearing assembly and hub. When replacing the Steering Knuckle landlords should first disconnect the outer Tie Rod End at the Steering Knuckle and also remove the road sensing suspension sensor link. Start by removing both parts of the lower ball joint. First remove the cotter pin followed by the retaining nut. The j 36226 ball joint separator (J 36226) disengages the Steering Knuckle from the lower Control Arm before removing the strut to Steering Knuckle retaining bolts and nuts and extracting the Steering Knuckle. Start the installation process by placing the new Steering Knuckle then fasten it with strut to Steering Knuckle retaining bolts and nuts. After connecting the lower ball joint to the Steering Knuckle install the lower ball joint retaining nut to a torque of 10 nm (7 lb-in) while adding an additional 150 degrees (2 1/2 flats) of rotation followed by an additional 60 degrees for proper cotter pin alignment. Link the road sensing suspension position sensor to the lower Control Arm then fasten the new cotter pin before reconnecting the Steering Knuckle to the outer Tie Rod End. When finished replace the Wheel Bearing together with the hub assembly and tire and wheel before lowering the vehicle. Vehicle technicians need to use the following tools for this operation: j 36226 ball joint separator (J 36226), j 35551 ball stud nut wrench (J 35551), and j 24319-b tie rod remover (J 24319-B).

OEM Cadillac Eldorado Steering Knuckle

Front Steering Knuckle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

21 Steering Knuckles found

View related parts
Cadillac Eldorado Knuckle, Driver Side Part Number: 3521226
$172.53 MSRP: $195.65
You Save: $23.12 (12%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle, Rear Suspension; Knuckle, Rear Wheel
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1990 Cadillac Eldorado | Base, Biarritz, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS
View related parts
Cadillac Eldorado Steering Knuckle, Driver Side Part Number: 1645255
$31.78 MSRP: $224.67
You Save: $192.89 (86%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle; Knuckle, Steering
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Cadillac Eldorado | Base, Biarritz, Spring Edition, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Eldorado Knuckle, Driver Side Part Number: 18021749
Product Specifications
- Other Name: Knuckle, Steering
- Position: Driver Side
- Replaced by: 88955416
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Cadillac Eldorado | Base, ESC, ETC | 8 Cyl 4.6 L GAS
View related parts
Cadillac Eldorado Steering Knuckle Part Number: 22522938
Product Specifications
- Other Name: Knuckle; Knuckle, Steering
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Cadillac Eldorado | Base, Biarritz, Cabriolet, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Cadillac Eldorado Knuckle, Rear Part Number: 3521227
Product Specifications
- Other Name: Knuckle, Rear Suspension
- Position: Rear
- Replaced by: 12491132
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1990 Cadillac Eldorado | Base, Biarritz, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS
View related parts
Cadillac Eldorado Knuckle, Passenger Side Part Number: 18021750
Product Specifications
- Other Name: Knuckle, Steering
- Position: Passenger Side
- Replaced by: 88955417
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Cadillac Eldorado | Base, ESC, ETC | 8 Cyl 4.6 L GAS
View related parts
Cadillac Eldorado Knuckle, Rear Passenger Side Part Number: 12491132
Product Specifications
- Other Name: Knuckle, Rear Suspension; Knuckle, Rear Wheel
- Position: Rear Passenger Side
- Replaces: 03521227, 3521227
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1990 Cadillac Eldorado | Base, Biarritz, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS
View related parts
Cadillac Eldorado Knuckle, Passenger Side Part Number: 3524112
Product Specifications
- Other Name: Knuckle-Rear Suspension; Knuckle, Rear Wheel
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 Cadillac Eldorado | Base, Biarritz, Sport, Spring Edition, Touring | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Eldorado Knuckle, Driver Side Part Number: 3521224
Product Specifications
- Other Name: Knuckle, Rear Wheel
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1990 Cadillac Eldorado | Base, Biarritz, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS
View related parts
Cadillac Eldorado Knuckle, Passenger Side Part Number: 3521225
Product Specifications
- Other Name: Knuckle, Rear Wheel
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1990 Cadillac Eldorado | Base, Biarritz, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS
View related parts
Cadillac Eldorado Steering Knuckle, Passenger Side Part Number: 1645256
Product Specifications
- Other Name: Knuckle; Knuckle, Steering
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Cadillac Eldorado | Base, Biarritz, Spring Edition, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Eldorado Steering Knuckle Part Number: 22522937
Product Specifications
- Other Name: Knuckle, Steering; Knuckle
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Cadillac Eldorado | Base, Biarritz, Cabriolet, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Cadillac Eldorado Knuckle, Driver Side Part Number: 3524111
Product Specifications
- Other Name: Knuckle-Rear Suspension; Knuckle, Rear Wheel
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 Cadillac Eldorado | Base, Biarritz, Sport, Spring Edition, Touring | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Eldorado Steering Knuckle, Passenger Side Part Number: 18060587
Product Specifications
- Other Name: Knuckle, Steering; Knuckle
- Position: Passenger Side
- Replaces: 18016759
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 Cadillac Eldorado | Base, Sport, Touring | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Eldorado Steering Knuckle, Driver Side Part Number: 18060586
Product Specifications
- Other Name: Knuckle, Steering; Knuckle
- Position: Driver Side
- Replaces: 18016758
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 Cadillac Eldorado | Base, Sport, Touring | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Eldorado Knuckle Part Number: 88955417
Product Specifications
- Other Name: Knuckle, Steering
- Replaces: 18060637, 18021750, 18026650, 18060679
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2002 Cadillac Eldorado | Base, ESC, ETC | 8 Cyl 4.6 L GAS
View related parts
Cadillac Eldorado Knuckle Part Number: 88955416
Product Specifications
- Other Name: Knuckle, Steering
- Replaces: 18026649, 18021749, 18060678, 18060636
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2002 Cadillac Eldorado | Base, ESC, ETC | 8 Cyl 4.6 L GAS
View related parts
Cadillac Eldorado Knuckle, Driver Side Part Number: 18060604
Product Specifications
- Other Name: Knuckle, Steering
- Position: Driver Side
- Replaces: 18020766
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Cadillac Eldorado | Base, ETC, Touring | 8 Cyl 4.6 L GAS
View related parts
Cadillac Eldorado Knuckle, Passenger Side Part Number: 18060605
Product Specifications
- Other Name: Knuckle, Steering
- Position: Passenger Side
- Replaces: 18020767
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Cadillac Eldorado | Base, ETC, Touring | 8 Cyl 4.6 L GAS
View related parts
Cadillac Eldorado Knuckle, Rear Driver Side Part Number: 18026757
Product Specifications
- Other Name: Knuckle, Rear Suspension; Knuckle, Rear Wheel
- Position: Rear Driver Side
- Replaces: 18023709, 18021056
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-2002 Cadillac Eldorado | Base, ESC, ETC, Sport, Touring | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS

| Page 1 of 2 |Next >

1-20 of 21 Results

Cadillac Eldorado Steering Knuckle

Want to cut long-term maintenance and repair costs? Choose OEM Steering Knuckle. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Cadillac Eldorado parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Cadillac Eldorado Steering Knuckle includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Steering Knuckle of Cadillac Eldorado vehicles is an assembly part that joins the suspension and the steering of the vehicle with the front wheels. It is where the control arms, the tie-rod ends and even housing for the spindle or hubs that the wheels are fixed to are located. Depending on the offered drive, there are typical and non-typical types of steering knuckles, which are mainly differ by the type of spindle and hub. Comparing the kingpin and ball joint types of the steering knuckles outlines the progress in the auto suspension system design. Periodic check up of the knuckle stud bores and spindles is required so that necessary correction can be made so that it does not lead to failure which would lead to replacement.

Cadillac Eldorado Steering Knuckle Parts and Q&A

Knuckle, Rear Passenger Side
18026758
Q: What tools are required to service and repair the steering knuckle on Cadillac Eldorado?
A:
Service and repairs of the Steering Knuckle require three essential tools: ball stud separator (J36226) ball stud nut wrench (J35551) and tie rod remover (J24319-B). Three necessary tools include ball stud separator (J36226), ball stud nut wrench (J35551), and tie rod remover (J24319-B). Start with wheel lifting and vehicle support followed by tire removal and moving onward to Wheel Bearing assembly and hub replacement. Disconnect the outer tie rod at the Steering Knuckle before removing the road sensing suspension sensor link. You must remove both the lower Ball Joint cotter pin alongside the retaining nut. Apply the ball stud separator (J36226) on the Steering Knuckle to detach it from the lower Control Arm before unfastening the strut to Steering Knuckle retaining nuts and bolts. Install the new Steering Knuckle after which you should attach the lower Ball Joint to this knuckle's assembly. Secure the bottom part of the suspension strut to the Steering Knuckle through retaining bolts and nuts while following manufacturer-recommended fastener torque values. Tighten the lower Ball Joint retaining nut to 10 nm (7 inch lbs.) but continue tightening an additional 150 degrees (2 1/2 flats) in addition to a 60-degree alignment for the cotter pin. Insert a fresh cotter pin afterward you must link the road sensing suspension position sensor to the lower Control Arm followed by reconnecting the outer Tie Rod End to the Steering Knuckle. Reinstall the Wheel Bearing and hub assembly as well as the tire and wheel before lowering the vehicle down.
Knuckle, Rear Driver Side
18026757
Q: How to replace the steering knuckle on Cadillac Eldorado?
A:
The Steering Knuckle replacement process begins with vehicle support followed by wheel and tire separation then elimination of the bearing assembly and hub. When replacing the Steering Knuckle landlords should first disconnect the outer Tie Rod End at the Steering Knuckle and also remove the road sensing suspension sensor link. Start by removing both parts of the lower ball joint. First remove the cotter pin followed by the retaining nut. The j 36226 ball joint separator (J 36226) disengages the Steering Knuckle from the lower Control Arm before removing the strut to Steering Knuckle retaining bolts and nuts and extracting the Steering Knuckle. Start the installation process by placing the new Steering Knuckle then fasten it with strut to Steering Knuckle retaining bolts and nuts. After connecting the lower ball joint to the Steering Knuckle install the lower ball joint retaining nut to a torque of 10 nm (7 lb-in) while adding an additional 150 degrees (2 1/2 flats) of rotation followed by an additional 60 degrees for proper cotter pin alignment. Link the road sensing suspension position sensor to the lower Control Arm then fasten the new cotter pin before reconnecting the Steering Knuckle to the outer Tie Rod End. When finished replace the Wheel Bearing together with the hub assembly and tire and wheel before lowering the vehicle. Vehicle technicians need to use the following tools for this operation: j 36226 ball joint separator (J 36226), j 35551 ball stud nut wrench (J 35551), and j 24319-b tie rod remover (J 24319-B).