How to service and repair the slip yoke on Cadillac Escalade?

There are two essential tools required to service and repair the Slip Yoke: u joint bearing separator (J9522-3) and u joint bearing spacer remover (J9522-5). The replacement of a propeller shaft Slip Yoke demands replacing the adjacent Universal Joint for protecting the components from damage. Begin by removing the propeller shaft from its location while placing it horizontally on a clamp at a yoke instead of using a vise clamp for tubing. Apply marks to the propeller shaft for determining its transmission interface and its rear axle interface. The snap rings can be removed using plier pressure on their ends while a gentle tap on the bearing cup helps reduce the pressure inside. Workers should use a 30 mm (1 1/8 inch) socket to support the lower propeller shaft yoke for removing the bearing cup with the u joint bearing separator (J9522-3). The u joint bearing spacer remover (J9522-5) must be inserted between the seal and the bearing cup when the cup fails to come out fully, then the user should continue pressing. Press the opposite bearing cup out of the propeller shaft by rotating the propeller shaft with the intention to discard all reinstallation of Universal Joint components. The cross and Slip Yoke should be removed from the propeller shaft yoke to check for burrs or imperfections in the bearing cup bores. During installation, lubricate each needle bearing before placing one bearing cup half into the propeller shaft yoke. Pass the yoke ear down before inserting the crosspiece along with pressing the bearing cup until it matches the yoke ear position. Complete the same process for the other bearing cup by keeping trunnions facing forward. A technician should press the bearing cup into the yoke ear through the cross while performing installation checks to confirm proper unbinding function. After pressing until the groove of the bearing retainer appears you should place the bearing retainer. Adding chassis grease during installation may help the retainer seating process. To assist retainer seating use a dead blow hammer to apply gentle force on the yoke slightly. The installation process should be performed again for attaching the Universal Joint to the Slip Yoke.

OEM Cadillac Escalade Slip Yoke

Transmission Slip Yoke

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

21 Slip Yokes found

View related parts
Cadillac Escalade Slip Yoke, Front
Part Number: 23251196
$206.59 MSRP: $502.74
You Save: $296.15 (59%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Yoke-Propeller Shaft Front Slip; Driveshaft Yokes; Yoke, Universal Joint And Power Divider
- Position: Front
- Replaces: 22944357, 07839467, 7839467, 88964470
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2015 Cadillac Escalade | Base, Hybrid, Hybrid Platinum, Luxury, Platinum, Premium | 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade Slip Yoke, Front
Part Number: 22944359
$199.20 MSRP: $339.11
You Save: $139.91 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Yoke-Propeller Shaft Front Slip; Driveshaft Yokes; Yoke, Universal Joint And Power Divider
- Position: Front
- Replaces: 15926348
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2014 Cadillac Escalade | Base, Luxury, Platinum, Premium | 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade Slip Yoke
Part Number: 88963576
$235.08 MSRP: $403.73
You Save: $168.65 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Yoke, Universal Joint And Power Divider; Driveshaft Yokes
- Replaces: 12479383, 07838665, 7838665
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2008 Cadillac Escalade | Base, Platinum | 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade Slip Yoke
Part Number: 7848635
$240.33 MSRP: $381.56
You Save: $141.23 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Yoke Assembly-Slip; Driveshaft Yokes; Yoke, Universal Joint And Power Divider
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2006, 1999-2000 Cadillac Escalade | Base | 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS
View related parts
Cadillac Escalade Universal Joints
Part Number: 12471638
$46.00 MSRP: $112.28
You Save: $66.28 (60%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Yoke, Universal Joint And Power Divider; Driveshaft Yokes; Slip Yoke
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2014 Cadillac Escalade | Base, Hybrid, Hybrid Platinum, Luxury, Platinum, Premium | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade Companion Flange
Part Number: 88967027
$47.60 MSRP: $116.14
You Save: $68.54 (60%)
ADD TO CART
Product Specifications
- Other Name: Flange, Propeller Shaft Pinion; Yoke, Propeller Shaft Pinion
- Position: Front
- Replaces: 15588336
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2014 Cadillac Escalade | Base, Hybrid, Hybrid Platinum, Luxury, Platinum, Premium | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade Companion Flange
Part Number: 84881462
$103.06 MSRP: $161.43
You Save: $58.37 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Yoke Kit-Differential Drive Pinion Gear; Double Cardan CV Centering Yoke; Yoke; Yoke Kit, Propeller Shaft Pinion
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Cadillac Escalade | Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade Slip Yoke
Part Number: 88934934
$114.59 MSRP: $180.30
You Save: $65.71 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Yoke Assembly, Propeller Shaft Slip (W/Universal Joint); Driveshaft Yokes
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002 Cadillac Escalade | Base | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Cadillac Escalade Companion Flange
Part Number: 84584310
$342.83 MSRP: $539.43
You Save: $196.60 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Yoke Kit-Front Differential Drive Pinion Gear; Yoke
- Position: Front
- Replaced by: 84798161
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Cadillac Escalade | Luxury, Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum, V | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade Slip Yoke
Part Number: 84868130
$108.27 MSRP: $169.59
You Save: $61.32 (37%)
ADD TO CART
Product Specifications
- Other Name: Yoke Kit-Differential Drive Pinion Gear; Double Cardan CV Centering Yoke; Driveshaft Yokes; Companion Flange; Yoke; Yoke Kit, Propeller Shaft Pinion
- Replaces: 84446298, 84833855
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Cadillac Escalade | Luxury, Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum, V | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade Companion Flange
Part Number: 22876134
$42.61 MSRP: $73.18
You Save: $30.57 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Yoke, Propeller Shaft Pinion
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Cadillac Escalade | Base, Luxury, Platinum, Premium, Premium Luxury | 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade Companion Flange
Part Number: 85524483
$93.33 MSRP: $146.20
You Save: $52.87 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Yoke Kit-Front Differential Drive Pinion Gear; Yoke; Yoke Kit, Propeller Shaft Pinion
- Replaces: 84428329
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Cadillac Escalade | Luxury, Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum, V | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade Drive Shaft
Part Number: 84389646
$89.64 MSRP: $153.91
You Save: $64.27 (42%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Yoke-Propeller Shaft Slip; Driveshaft Yokes; Slip Yoke; Yoke; Yoke, Universal Joint And Power Divider
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Cadillac Escalade | Luxury, Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum, V | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade Slip Yoke
Part Number: 84389645
$73.92 MSRP: $115.77
You Save: $41.85 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Yoke-Propeller Shaft Slip; Driveshaft Yokes; Yoke; Yoke, Universal Joint And Power Divider; Yoke, Universal Joint
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Cadillac Escalade | Luxury, Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum, V | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade Slip Yoke
Part Number: 12479384
Product Specifications
- Other Name: Yoke, Universal Joint And Power Divider; Driveshaft Yokes
- Replaces: 12471642
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2005 Cadillac Escalade | Base | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Cadillac Escalade Slip Yoke
Part Number: 19151749
Product Specifications
- Other Name: Yoke Kit, Universal Joint And Power Divider; Driveshaft Yokes
- Replaces: 88935866, 89058882, 89038580
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2006 Cadillac Escalade | Base | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Cadillac Escalade Slip Yoke
Part Number: 12542963
$62.55 MSRP: $97.98
You Save: $35.43 (37%)
Product Specifications
- Other Name: Yoke, Universal Joint And Power Divider; Driveshaft Yokes
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2004 Cadillac Escalade | Base | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Cadillac Escalade Companion Flange
Part Number: 15634021
$87.96 MSRP: $137.79
You Save: $49.83 (37%)
Product Specifications
- Other Name: Yoke, Differential Drive Pinion Gear; Yoke, Propeller Shaft Pinion
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2000 Cadillac Escalade | Base | 8 Cyl 5.7 L GAS
View related parts
Cadillac Escalade Companion Flange
Part Number: 26016668
Product Specifications
- Other Name: Flange; Yoke Kit, Propeller Shaft Pinion; Flange, Propeller Shaft Pinion; Yoke, Propeller Shaft Pinion
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2000 Cadillac Escalade | Base | 8 Cyl 5.7 L GAS
View related parts
Cadillac Escalade Slip Yoke
Part Number: 15153615
Product Specifications
- Other Name: Yoke, Universal Joint And Power Divider; Driveshaft Yokes
- Position: Front
- Replaces: 07816706, 7816706
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2000 Cadillac Escalade | Base | 8 Cyl 5.7 L GAS

| Page 1 of 2 |Next >

1-20 of 21 Results

Cadillac Escalade Slip Yoke

Our website offers an extensive catalog of genuine Cadillac Escalade Slip Yoke at unbeatable prices. Every OEM Cadillac Escalade Slip Yoke comes with a manufacturer's warranty, an easy return policy, and rapid delivery service. Don't miss out on this great opportunity!

Cadillac Escalade Slip Yoke Parts Questions & Experts Answers

Slip Yoke
7848635
Q: How to service and repair the slip yoke on Cadillac Escalade?
A: There are two essential tools required to service and repair the Slip Yoke: u joint bearing separator (J9522-3) and u joint bearing spacer remover (J9522-5). The replacement of a propeller shaft Slip Yoke demands replacing the adjacent Universal Joint for protecting the components from damage. Begin by removing the propeller shaft from its location while placing it horizontally on a clamp at a yoke instead of using a vise clamp for tubing. Apply marks to the propeller shaft for determining its transmission interface and its rear axle interface. The snap rings can be removed using plier pressure on their ends while a gentle tap on the bearing cup helps reduce the pressure inside. Workers should use a 30 mm (1 1/8 inch) socket to support the lower propeller shaft yoke for removing the bearing cup with the u joint bearing separator (J9522-3). The u joint bearing spacer remover (J9522-5) must be inserted between the seal and the bearing cup when the cup fails to come out fully, then the user should continue pressing. Press the opposite bearing cup out of the propeller shaft by rotating the propeller shaft with the intention to discard all reinstallation of Universal Joint components. The cross and Slip Yoke should be removed from the propeller shaft yoke to check for burrs or imperfections in the bearing cup bores. During installation, lubricate each needle bearing before placing one bearing cup half into the propeller shaft yoke. Pass the yoke ear down before inserting the crosspiece along with pressing the bearing cup until it matches the yoke ear position. Complete the same process for the other bearing cup by keeping trunnions facing forward. A technician should press the bearing cup into the yoke ear through the cross while performing installation checks to confirm proper unbinding function. After pressing until the groove of the bearing retainer appears you should place the bearing retainer. Adding chassis grease during installation may help the retainer seating process. To assist retainer seating use a dead blow hammer to apply gentle force on the yoke slightly. The installation process should be performed again for attaching the Universal Joint to the Slip Yoke.