How to replace the outer CV Boot and CV Joint on Chevrolet Tahoe?

Begin the outer wheel drive shaft joint and boot replacement by removing the halfshaft while being cautious near the cv joint outer race with the hand grinder. A hand grinder should be used to slice the swage ring before using side cutters to remove the small boot clamp. Move the boot away from the cv joint outer race down the halfshaft bar then clean all grease from the cv joint face. To access the halfshaft bar retaining snap ring within the inner race use j-8059 (Snap Ring Pliers) to spread open its ear sections. Remove the boot along with the cv joint from the halfshaft bar while discarding the old boot. Gently tap the cv joint cage with a brass drift to rock it so all six chrome alloy balls will come out. Soak the cv joint cage and inner race at 90 degrees alignment with the outer race so they can be lifted out. After cleaning the inner and outer race assemblies, cv joint cage, and chrome alloy balls with cleaning solvent to remove all old grease and contaminants, permit the components to dry before replacing any worn parts. Use a wire brush to clean the halfshaft bar as you remove rust from the area where the seals mount. Before applying recommended grease, examine all parts for damage and wear by brushing a thin coat into the inner race and outer race grooves. Set your inner race to a 90-degree angle with the cage and position it through the cage's windows before moving forward. Position the cage and inner race into the outer race before using a brass drift to tilt the cage for installing chrome alloy balls . Apply pre-measured grease from the kit onto both the cv joint boot and assembly before installing the new small boot clamp onto the cv joint seal and placing the boot onto the halfshaft bar with its small end fitting into the joint boot groove. Apply j-35910 (Drive Axle Seal Clamp Pliers) on the small boot clamp then torque the clamp to 136 nm (100 lb ft) while sustaining the specified gap between clamp ear surfaces. First distort the new swage ring into an oval shape and install it over the boot with its retaining ring side pointing at the halfshaft bar. Then put the cv joint on the bar until it locks. Check cv joint engagement by pulling the joint assembly then move the large boot diameter onto the cv joint outer race . The swage ring clamping process requires j-36652-1 (Drive Axle Clamp Swage Tool) for 1500 models but j-36652-2 (Axle Swage Tool) for 2500, 3500, and hummer h2 models. Clamp the base in a vise while aligning the cv joint boot , cv joint assembly , and swage ring . Placing each tool half around the cv joint boot together with assembly insert two bolts starting from opposite sides until the tool halves connect before removing the halfshaft fully to install the wheel drive component.

OEM Chevrolet Tahoe CV Boot

Axle Boot

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 CV Boots found

View related parts
Chevrolet Tahoe Inner Boot, Front
Part Number: 19256072
$47.56 MSRP: $81.62
You Save: $34.06 (42%)
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Boot Kit, Front Axle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2020 Chevrolet Tahoe | Hybrid, LS, LT, LTZ, PPV, Premier, SSV | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Outer Boot, Front
Part Number: 19256071
$106.39 MSRP: $182.69
You Save: $76.30 (42%)
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Axle; CV Boot
- Position: Front
- Replaces: 15868187, 26069246
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2020 Chevrolet Tahoe | Base, Hybrid, LS, LT, LTZ, PPV, Premier, SSV, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Inner Boot, Front
Part Number: 26062618
$33.23 MSRP: $54.75
You Save: $21.52 (40%)
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Outer Boot; Boot Kit, Front Axle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2005, 1998-1999 Chevrolet Tahoe | Base, LS, LT, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Inner Boot, Front
Part Number: 26062615
$27.42 MSRP: $43.53
You Save: $16.11 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Boot Kit, Front Axle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2013 Chevrolet Tahoe | Base, Hybrid, Limited, LS, LT, LTZ, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Outer Boot, Front
Part Number: 15868188
$63.86 MSRP: $109.66
You Save: $45.80 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Axle; CV Boot; Inner Boot
- Position: Front
- Replaces: 26062619
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2005, 1998-1999 Chevrolet Tahoe | Base, LS, LT, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Inner CV Joint Boot, Front
Part Number: 87863492
$38.27 MSRP: $59.94
You Save: $21.67 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; Inner Boot; Boot Kit, Front Axle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2022 Chevrolet Tahoe | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Boot Kit, Front
Part Number: 84392104
$26.60 MSRP: $41.67
You Save: $15.07 (37%)
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Outer Boot
- Position: Front
- Replaced by: 87842370
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Chevrolet Tahoe | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Outer CV Joint Boot, Front
Part Number: 87842370
$26.60 MSRP: $41.67
You Save: $15.07 (37%)
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; Outer Boot; Boot Kit, Front Axle
- Position: Front
- Replaces: 84392104
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Chevrolet Tahoe | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Boot Kit
Part Number: 84929646
$82.72 MSRP: $129.55
You Save: $46.83 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Boot Kit-Rear Wheel Drive Shaft CV & Tri-Pot Joint; Boot Kit, Rear Axle Universal Joint
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2022 Chevrolet Tahoe | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Boot Kit
Part Number: 84846848
$59.21 MSRP: $92.75
You Save: $33.54 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Boot Kit-Rear Wheel Drive Shaft CV & Tri-Pot Joint; Boot Kit, Rear Axle Universal Joint
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2022 Chevrolet Tahoe | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Inner Boot, Front
Part Number: 26055394
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Boot Kit, Front Axle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1997 Chevrolet Tahoe | Base, LS, LT | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Outer Boot, Front
Part Number: 26037370
Product Specifications
- Other Name: Boot Kit, Front Axle; CV Boot
- Position: Front
- Replaces: 26032807
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2000 Chevrolet Tahoe | Base, Limited, LS, LT, Z71 | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Outer Boot, Front
Part Number: 26037155
Product Specifications
- Other Name: Boot Kit, Front Axle; CV Boot
- Position: Front
- Replaces: 26020729
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1997 Chevrolet Tahoe | Base, LS, LT | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Inner Boot, Front
Part Number: 26036985
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Boot Kit, Front Axle
- Position: Front
- Replaces: 07849566, 7849566, 26018970
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1997 Chevrolet Tahoe | Base, LS, LT | 8 Cyl 5.7 L GAS

Chevrolet Tahoe CV Boot

Our website offers an extensive catalog of genuine Chevrolet Tahoe CV Boot at unbeatable prices. Every OEM Chevrolet Tahoe CV Boot comes with a manufacturer's warranty, an easy return policy, and rapid delivery service. Don't miss out on this great opportunity!

Chevrolet Tahoe CV Boot Parts Questions & Experts Answers

Outer Boot, Front
19256071
Q: How to replace the outer CV Boot and CV Joint on Chevrolet Tahoe?
A: Begin the outer wheel drive shaft joint and boot replacement by removing the halfshaft while being cautious near the cv joint outer race with the hand grinder. A hand grinder should be used to slice the swage ring before using side cutters to remove the small boot clamp. Move the boot away from the cv joint outer race down the halfshaft bar then clean all grease from the cv joint face. To access the halfshaft bar retaining snap ring within the inner race use j-8059 (Snap Ring Pliers) to spread open its ear sections. Remove the boot along with the cv joint from the halfshaft bar while discarding the old boot. Gently tap the cv joint cage with a brass drift to rock it so all six chrome alloy balls will come out. Soak the cv joint cage and inner race at 90 degrees alignment with the outer race so they can be lifted out. After cleaning the inner and outer race assemblies, cv joint cage, and chrome alloy balls with cleaning solvent to remove all old grease and contaminants, permit the components to dry before replacing any worn parts. Use a wire brush to clean the halfshaft bar as you remove rust from the area where the seals mount. Before applying recommended grease, examine all parts for damage and wear by brushing a thin coat into the inner race and outer race grooves. Set your inner race to a 90-degree angle with the cage and position it through the cage's windows before moving forward. Position the cage and inner race into the outer race before using a brass drift to tilt the cage for installing chrome alloy balls . Apply pre-measured grease from the kit onto both the cv joint boot and assembly before installing the new small boot clamp onto the cv joint seal and placing the boot onto the halfshaft bar with its small end fitting into the joint boot groove. Apply j-35910 (Drive Axle Seal Clamp Pliers) on the small boot clamp then torque the clamp to 136 nm (100 lb ft) while sustaining the specified gap between clamp ear surfaces. First distort the new swage ring into an oval shape and install it over the boot with its retaining ring side pointing at the halfshaft bar. Then put the cv joint on the bar until it locks. Check cv joint engagement by pulling the joint assembly then move the large boot diameter onto the cv joint outer race . The swage ring clamping process requires j-36652-1 (Drive Axle Clamp Swage Tool) for 1500 models but j-36652-2 (Axle Swage Tool) for 2500, 3500, and hummer h2 models. Clamp the base in a vise while aligning the cv joint boot , cv joint assembly , and swage ring . Placing each tool half around the cv joint boot together with assembly insert two bolts starting from opposite sides until the tool halves connect before removing the halfshaft fully to install the wheel drive component.