How to replace the rear Drive Shaft on Chevrolet Tahoe?

Before removing the driveline components the technician must reference mark every piece accurately relative to both propeller shafts and axles and pinion flanges and output shafts to preserve the current relationship between components according to specified torque values. Begin by raising the vehicle. The propeller shaft requires two reference marks before removal: behind the transmission or Transfer Case and at the rear axle pinion yoke. Use a tool to detach both bolts and retainer components from the rear axle pinion yoke structure. Pounding on the yoke ears and inserting tools between yoke and Universal Joint must be avoided because it will lead to broken injection joints. Begin this operation by moving the propeller shaft toward the front to separate it from the rear axle pinion yoke and then push it all the way toward the tail to detach from the transmission or Transfer Case and finally extract the propeller shaft from the vehicle. Before installing the Slip Yoke inspect the pinion yoke splines for an adequate lubricant amount. If needed, lubricate using gm p/n 12345879 (Canadian P/N 10953511) or an equivalent component that meets gm specification 9985830 (RWD w/4-speed Automatic Transmission). Insert the propeller shaft into the transmission or Transfer Case while matching the reference marks from removal before attaching the rear axle pinion yoke by matching both reference marks. Extra precaution needs to be taken about fasteners. When complete you should install the yoke retainers and bolts and fasten them to 25 nm (18 lb ft) then lower the vehicle.

How to replace the front drive shaft on Chevrolet Tahoe?

A vehicle rise is first required to replace the front propeller shaft. Start by removing the transfer case shield but perform shield renewal based on the bw 4485-nr3 or mp 3023/3024-nqh transfer case specific instructions. Use a flat-bladed tool to pry up the clamp located at the transfer case. Squeezing yoke ears or inserting tools between the joint and the universal alignment will result in damage to the injection points. Mark the attachment point of the front propeller shaft to the front axle flange then drain out the retaining bolts from both pinion yoke retainers while keeping the bearing assemblies in place. Newly secured bearing caps with tape follow the disconnect of the propeller shaft from the front axle pinion yoke. First remove the boot covering the transfer case output shaft groove before taking off the propeller shaft from the output shaft. First step to remove the boot clamp from the axis shaft joint and proceed with boot extraction. The installation process requires inspection of transfer case output shaft splines for sufficient lubrication which you can add gm p/n 12345879 (Canadian P/N 10953511) grease or equivalent grease with gm specification 9985830. Mount the propeller shaft boot and its boot clamp onto the transfer case output shaft before introducing the propeller shaft splines to match the relationship marks. Position the propeller shaft back to the front axle pinion yoke while both reference marks must match. Combine the Universal Joint retainers with their bolts and tighten them to reach 25 nm (18 lb ft) torque. Use the j-43218 clamp pliers narrow jaw to crimp the clamps after setting the boot onto the transfer case output shaft where it rests in the groove. Install the transfer case shield according to the specific needs followed by transfer case fluid check and vehicle lowering.

OEM Chevrolet Tahoe Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

20 Drive Shafts found

View related parts
Chevrolet Tahoe Drive Shaft, Front Part Number: 22760960
$398.11 MSRP: $696.20
You Save: $298.09 (43%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Driveshaft; Drive Shaft Assembly; Shaft, Propeller
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Chevrolet Tahoe | LS, LT, LTZ, PPV, Premier, SSV | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Drive Shaft Part Number: 84997910
$427.57 MSRP: $672.76
You Save: $245.19 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller
- Replaced by: 87821415
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2022 Chevrolet Tahoe | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Drive Shaft Part Number: 84997913
$425.39 MSRP: $669.32
You Save: $243.93 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Shaft, Propeller
- Replaced by: 85816902
- Replaces: 84712240
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Chevrolet Tahoe | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Drive Shaft Part Number: 84997912
$338.82 MSRP: $533.12
You Save: $194.30 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Shaft, Propeller
- Replaced by: 85816901
- Replaces: 84712239
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Chevrolet Tahoe | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Drive Shaft Part Number: 23486754
$700.07 MSRP: $900.99
You Save: $200.92 (23%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2020 Chevrolet Tahoe | Premier | 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Drive Shaft Part Number: 84546235
$1291.54 MSRP: $2010.72
You Save: $719.18 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 23209519, 23469168, 23251188, 23469170, 84083947
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2020 Chevrolet Tahoe | Premier | 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Drive Shaft Part Number: 84202541
$817.28 MSRP: $1370.84
You Save: $553.56 (41%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 23469167, 23251187, 23469169
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Chevrolet Tahoe | LS, LT, LTZ, PPV, Premier, SSV | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Tahoe Drive Shaft Part Number: 84202543
$967.86 MSRP: $1507.12
You Save: $539.26 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 23469161, 22760927, 23259048
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Chevrolet Tahoe | LS, LT, LTZ, PPV, Premier, SSV | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Tahoe Drive Shaft, Front Part Number: 85519802
$285.90 MSRP: $449.74
You Save: $163.84 (37%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Shaft, Propeller
- Position: Front
- Replaced by: 85075685
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Chevrolet Tahoe | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Drive Shaft, Front Part Number: 22845694
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Driveshaft; Shaft, Propeller
- Position: Front
- Replaces: 15902927
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2014 Chevrolet Tahoe | Hybrid, LS, LT, LTZ, SSV | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Drive Shaft Part Number: 15814472
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2008 Chevrolet Tahoe | LS, LT, LTZ | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Drive Shaft Part Number: 22845689
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 20912705, 20871266, 25932512, 22828501
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2014 Chevrolet Tahoe | LS, LT, LTZ, SSV | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX
View related parts
Chevrolet Tahoe Axle Shaft, Front Part Number: 26056795
Product Specifications
- Other Name: Shaft, Front Wheel Drive; Shaft
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2000 Chevrolet Tahoe | Base, Limited, LS, LT, Z71 | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Drive Shaft, Front Part Number: 22845693
$277.89 MSRP: $437.25
You Save: $159.36 (37%)
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Driveshaft; Shaft, Propeller
- Position: Front
- Replaces: 15902926
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2014 Chevrolet Tahoe | LS, LT, LTZ, SSV | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Drive Shaft Part Number: 25932511
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009 Chevrolet Tahoe | LS, LT, LTZ | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Tahoe Drive Shaft Part Number: 20912715
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 15930932, 25915400
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2013 Chevrolet Tahoe | Hybrid | 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV)
View related parts
Chevrolet Tahoe Drive Shaft Part Number: 22845691
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 20887168, 20887169, 20935680, 25942915
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2013 Chevrolet Tahoe | LS, LT, LTZ, PPV, SSV | 8 Cyl 5.3 L FLEX, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Axle Shaft, Rear Part Number: 26020040
Product Specifications
- Other Name: Shaft, Rear Axle Drive; Axle Shafts
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Tahoe | Base, LS, LT | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Drive Shaft Part Number: 15916624
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 15814473
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2008 Chevrolet Tahoe | LS, LT, LTZ | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Tahoe Drive Shaft Part Number: 20912701
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 15930933
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2013 Chevrolet Tahoe | Hybrid | 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV)

Chevrolet Tahoe Drive Shaft

Want to cut long-term maintenance and repair costs? Choose OEM Drive Shaft. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Tahoe parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Tahoe Drive Shaft includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Drive Shaft is a significant part in Chevrolet Tahoe vehicle; it transfers mechanical power and torque to the wheels, for the proper functioning of the vehicle from the engine or transmission. This particular heavy metal rod is designed to rotate at a very high speed and, so long as it is not destroyed in some way, should not fail during the vehicle's lifetime. Current Chevrolet Tahoptimal designs bear a powerful Drive Shaft that may contain universal joints to cater for the alignment differences. Various types of driveshafts have been used for example the one piece and the two piece which gave additional crash safety. The torsional rigidity combined with shear stress capability of the driveshaft is the power and resilience that is a fundamental aspect of the vehicle.

Chevrolet Tahoe Drive Shaft Parts and Q&A

Drive Shaft
22845689
Q: How to replace the rear Drive Shaft on Chevrolet Tahoe?
A:
Before removing the driveline components the technician must reference mark every piece accurately relative to both propeller shafts and axles and pinion flanges and output shafts to preserve the current relationship between components according to specified torque values. Begin by raising the vehicle. The propeller shaft requires two reference marks before removal: behind the transmission or Transfer Case and at the rear axle pinion yoke. Use a tool to detach both bolts and retainer components from the rear axle pinion yoke structure. Pounding on the yoke ears and inserting tools between yoke and Universal Joint must be avoided because it will lead to broken injection joints. Begin this operation by moving the propeller shaft toward the front to separate it from the rear axle pinion yoke and then push it all the way toward the tail to detach from the transmission or Transfer Case and finally extract the propeller shaft from the vehicle. Before installing the Slip Yoke inspect the pinion yoke splines for an adequate lubricant amount. If needed, lubricate using gm p/n 12345879 (Canadian P/N 10953511) or an equivalent component that meets gm specification 9985830 (RWD w/4-speed Automatic Transmission). Insert the propeller shaft into the transmission or Transfer Case while matching the reference marks from removal before attaching the rear axle pinion yoke by matching both reference marks. Extra precaution needs to be taken about fasteners. When complete you should install the yoke retainers and bolts and fasten them to 25 nm (18 lb ft) then lower the vehicle.
Drive Shaft, Front
22845693
Q: How to replace the front drive shaft on Chevrolet Tahoe?
A:
A vehicle rise is first required to replace the front propeller shaft. Start by removing the transfer case shield but perform shield renewal based on the bw 4485-nr3 or mp 3023/3024-nqh transfer case specific instructions. Use a flat-bladed tool to pry up the clamp located at the transfer case. Squeezing yoke ears or inserting tools between the joint and the universal alignment will result in damage to the injection points. Mark the attachment point of the front propeller shaft to the front axle flange then drain out the retaining bolts from both pinion yoke retainers while keeping the bearing assemblies in place. Newly secured bearing caps with tape follow the disconnect of the propeller shaft from the front axle pinion yoke. First remove the boot covering the transfer case output shaft groove before taking off the propeller shaft from the output shaft. First step to remove the boot clamp from the axis shaft joint and proceed with boot extraction. The installation process requires inspection of transfer case output shaft splines for sufficient lubrication which you can add gm p/n 12345879 (Canadian P/N 10953511) grease or equivalent grease with gm specification 9985830. Mount the propeller shaft boot and its boot clamp onto the transfer case output shaft before introducing the propeller shaft splines to match the relationship marks. Position the propeller shaft back to the front axle pinion yoke while both reference marks must match. Combine the Universal Joint retainers with their bolts and tighten them to reach 25 nm (18 lb ft) torque. Use the j-43218 clamp pliers narrow jaw to crimp the clamps after setting the boot onto the transfer case output shaft where it rests in the groove. Install the transfer case shield according to the specific needs followed by transfer case fluid check and vehicle lowering.