How to service the Steering Angle Sensor on Chevrolet Tahoe?

Service on the Steering Angle Sensor begins by checking sensor type before aligning the sensor connector's front connector on the right side. The adapter and bearing assembly requires the removal of both sensor and connector before proceeding. A pre-removal centering step is unnecessary when preserving the same sensor for reuse. Before removing the sensor create a reference mark on the flush rotor flange cuff so the components stay properly aligned during replacement. During installation keep the pin in place until you successfully position the sensor. Place the sensor against the Steering Shaft with the front position of the sensor showing a foam ring and a pin hole alongside the flushed rotor flange cuff and alignment mark. Connect the device while checking that the sensor back contains double d flats in addition to a foam ring and an alignment tab set-up. The installation process for extra sensors requires repetition of alignment steps while maintaining rotor flange cuff alignment marks throughout sensor positioning. Make sure to check that the front section of the sensor uses proper holes and marks for correct setup.

OEM Chevrolet Tahoe Steering Angle Sensor

Steering Column Angle Position Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Steering Angle Sensors found

View related parts
Chevrolet Tahoe Position Sensor
Part Number: 13589991
$58.78 MSRP: $114.10
You Save: $55.32 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Steering Gear Hydraulic Valve; Steering Wheel Speed Sensor; Steering Angle Sensor; Angle Sensor; Steering Sensor Assembly
- Replaces: 13579709, 13589257, 13584209, 13513905
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Chevrolet Tahoe | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Position Sensor
Part Number: 19418403
$58.84 MSRP: $100.20
You Save: $41.36 (42%)
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly, Steering Wheel Position; Steering Wheel Speed Sensor; Steering Angle Sensor; Sensor, Steering Column
- Replaces: 20910871
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2011-2014 Chevrolet Tahoe | Hybrid, LS, LT, LTZ, PPV, SSV | 8 Cyl 5.3 L FLEX, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV)
View related parts
Chevrolet Tahoe Position Sensor
Part Number: 26104070
$129.89 MSRP: $254.28
You Save: $124.39 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Steering Column; Steering Wheel Speed Sensor; Steering Angle Sensor
- Replaces: 26100011
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2006 Chevrolet Tahoe | Base, LS, LT, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Tahoe Position Sensor
Part Number: 13590209
$71.92 MSRP: $139.58
You Save: $67.66 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Steering Gear Hydraulic Valve; Steering Wheel Speed Sensor; Steering Angle Sensor; Angle Sensor; Sensor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Chevrolet Tahoe | LS, LT, LTZ, PPV, Premier, SSV | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Position Sensor
Part Number: 26084178
Product Specifications
- Other Name: Sensor, Steering Column; Steering Wheel Speed Sensor; Steering Angle Sensor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2002 Chevrolet Tahoe | Base, LS, LT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Tahoe Position Sensor
Part Number: 15886733
Product Specifications
- Other Name: Sensor, Steering Column; Steering Wheel Speed Sensor; Steering Angle Sensor
- Replaces: 15112675, 25833069
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2013 Chevrolet Tahoe | Hybrid, LS, LT, LTZ | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Speed Sensor
Part Number: 26064468
$72.07 MSRP: $128.70
You Save: $56.63 (44%)
Product Specifications
- Other Name: Sensor, Steering Column; Steering Wheel Speed Sensor; Steering Angle Sensor; Position Sensor; Sensor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2000 Chevrolet Tahoe | Base, Limited, LS, LT, Z71 | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Position Sensor
Part Number: 26091590
Product Specifications
- Other Name: Sensor Kit, Steering; Steering Wheel Speed Sensor; Sensor
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002 Chevrolet Tahoe | LS, LT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS

Chevrolet Tahoe Steering Angle Sensor

Our website offers an extensive catalog of genuine Chevrolet Tahoe Steering Angle Sensor at unbeatable prices. Every OEM Chevrolet Tahoe Steering Angle Sensor comes with a manufacturer's warranty, an easy return policy, and rapid delivery service. Don't miss out on this great opportunity!

Chevrolet Tahoe Steering Angle Sensor Parts Questions & Experts Answers

Position Sensor
26104070
Q: How to service the Steering Angle Sensor on Chevrolet Tahoe?
A: Service on the Steering Angle Sensor begins by checking sensor type before aligning the sensor connector's front connector on the right side. The adapter and bearing assembly requires the removal of both sensor and connector before proceeding. A pre-removal centering step is unnecessary when preserving the same sensor for reuse. Before removing the sensor create a reference mark on the flush rotor flange cuff so the components stay properly aligned during replacement. During installation keep the pin in place until you successfully position the sensor. Place the sensor against the Steering Shaft with the front position of the sensor showing a foam ring and a pin hole alongside the flushed rotor flange cuff and alignment mark. Connect the device while checking that the sensor back contains double d flats in addition to a foam ring and an alignment tab set-up. The installation process for extra sensors requires repetition of alignment steps while maintaining rotor flange cuff alignment marks throughout sensor positioning. Make sure to check that the front section of the sensor uses proper holes and marks for correct setup.