Other Name: Switch Assembly-Door Lock & Side Window; Switch, Door And End Gate Electrical
Position: Passenger Side
Replaces: 15093445, 15906882, 20877339, 25783952
Fits the following GMC Models:
Sierra 1500 | 2007-2013 | Denali, Hybrid, SL, SLE, SLT, WT, XFE | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
Sierra 2500 HD | 2007-2014 | Denali, SLE, SLT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
Sierra 3500 HD | 2007-2014 | Denali, SLE, SLT, WT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
Yukon | 2007-2014 | Denali, Denali Hybrid, Hybrid, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
Yukon XL 1500 | 2007-2014 | Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
Yukon XL 2500 | 2007-2013 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS
Other Name: Switch, Door Electric And Vacuum Locks; Door Lock Switch; Switch, Door And End Gate Electrical
Position: Passenger Side
Fits the following GMC Models:
Sierra 1500 | 2007-2009 | Denali, Hybrid, SL, SLE, SLT, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
Sierra 2500 HD | 2007-2009 | SLE, SLT, WT | 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
Sierra 3500 HD | 2007-2009 | SLE, SLT, WT | 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
Other Name: Switch, Door Electric And Vacuum Locks; Door Lock Actuator Motor; Lock Switch; Switch; Actuator; Switch, Door And End Gate Electrical; Switch, Door Lock
Position: Passenger Side
Fits the following GMC Models:
Savana 1500 | 2003-2006 | Base, LS, LT, SLE | 6 Cyl 4.3 L GAS, 8 Cyl 5.3 L GAS
Savana 2500 | 2003-2006 | Base, SLE | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
Savana 3500 | 2003-2006 | Base, LS, LT, SLE | 8 Cyl 4.8 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
Q: How to replace the passenger door lock switch and power window switch on GMC Envoy?
A: The process to replace the passenger Door Lock and side window switch starts with lifting the front part of the switch panel until the front retaining clip releases. Then work on the rear side of the panel to release the two remaining retaining clips. Federal that controls the passenger side must have its electrical connectors disconnected before removal. Alternatively when only replacing this module conduct the removal procedure from the door trim panel. Secure the remaining electrical components from the switch panel then maintain the passenger door module as part of the necessary transfer in case the switch panel is the only part being replaced. Take off the switch panel assembly that is installed in the vehicle. Place the passenger door module onto the door trim panel before you attach its electrical connector. When changing only the switch panel maintain connector attachment for all remaining electrical wires. The service programming system (SPS) needs to be used for programming the replacement passenger door module because setup procedures are required. You should mount the switch panel onto the door trim panel while verifying that both front and rear retaining clips sit within their intended positions.
Q: How to remove and replace the Power Door Lock Switch on GMC Canyon?
A: The initial step to replace the Power Door Lock Switch demands users to remove the 2 screws which fasten the switch plate assembly to the door trim panel. First raise the front side of the switch plate to unclip it before removing the switch plate from the door trim panel window. Remove the Power Door Lock Switch plate assembly from your vehicle by first disconnecting electrical connectors (3, 4) from switches (2, 5). The replacement process demands removing the switches from the plate while retaining them for transfer if the switch plate needs replacement only. Install the switches (2, 5) to the switch plate then connect electrical connectors (3, 4) to switches (2, 5). Use the two screws to install the switch plate assembly onto the door trim panel while tightening the front door switch plate screws to 2 N.m (18 lb in).