How to replace the harmonic balancer on GMC Savana 2500?

The first step to replace a crankshaft balancer involves removing either the air conditioning belt when there is one or the accessory belt if there is no air conditioning system. Beginning by removing the Starter motor and lower Fan Shroud the technician should check that the Flywheel holding tool (J 42386-A) establishes tooth engagement with the engine Flywheel. Use one m10-1.5 x 120 mm bolt and one m10-1.5 x 45 mm bolt to fasten the j 42386-a before tightening them to 50 nm (37 ft. Lbs.). The bolt securing the crankshaft balancer needs removal for later reuse during the installation process. The crankshaft balancer remover (J 41816) combined with the crankshaft end protector (J 41816-2) allows you to remove the crankshaft balancer after cleaning and inspecting it. Then install the crankshaft balancer by aligning it directly on the crankshaft followed by the use of crankshaft balancer and sprocket installer (J 41665). Use the threaded rod along with its nut and washer along with the installer to start installation at the front end of the balancer. Hold the threaded rod hex section using a wrench while turning the installation tool nut clockwise with another wrench until the first part of crankshaft installation completes. Use the installation tool to drive the bigger end of the balancer against the front section until the complete installation is achieved. The previous crankshaft balancer bolt should be installed before tightening it to 330 nm (240 ft. Lbs.). Next remove the bolt. Measure the installation position of the balancer again; if necessary use the j 41665 to reinstall correctly. You should use a new crankshaft balancer bolt which requires an initial torque of 50 nm (37 ft. Lbs.) followed by the 140 degrees setting measured with the torque angle meter (J 36660-A). The procedure completes with Starter motor installation followed by lower Fan Shroud adjunction along with accessory Drive Belt installation unless a/c is present and its Drive Belt installation until executing the crankshaft position learn sequence.

OEM GMC Savana 2500 Harmonic Balancer

Engine Harmonic Balancer

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Harmonic Balancers found

View related parts
GMC Savana 2500 Vibration Damper
Part Number: 19300488
$124.01 MSRP: $195.11
You Save: $71.10 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Damper, Engine Crankshaft And Camshaft Balancer; Balancer, Engine Crankshaft And Camshaft Balancer; Balancer, Engine Crankshaft
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2020 GMC Savana 2500 | Base, LS, LT, SLE | 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS
View related parts
GMC Savana 2500 Crankshaft Pulley
Part Number: 12684590
$90.59 MSRP: $141.89
You Save: $51.30 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulley; Harmonic Balancer Puller; Harmonic Balancer; Vibration Damper; Balancer, Engine Crankshaft And Camshaft Balancer
- Replaces: 12620312, 12662037
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018 GMC Savana 2500 | Base, LS, LT | 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS
View related parts
GMC Savana 2500 Vibration Damper
Part Number: 10243271
$97.87 MSRP: $153.30
You Save: $55.43 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulley; Balancer, Engine Crankshaft And Camshaft Balancer
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-2002 GMC Savana 2500 | Base, SLE, SLT | 8 Cyl 5.7 L BI-FUEL, 8 Cyl 5.7 L GAS
View related parts
GMC Savana 2500 Vibration Damper
Part Number: 10224885
$68.02 MSRP: $106.52
You Save: $38.50 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Balancer, Crankshaft; Harmonic Balancer; Balance Shaft; Crankshaft Damper; Balancer; Balancer, Engine Crankshaft And Camshaft Balancer
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-2006 GMC Savana 2500 | Base, SLE, SLT | 6 Cyl 4.3 L GAS
View related parts
GMC Savana 2500 Vibration Damper
Part Number: 19432547
$315.55 MSRP: $496.49
You Save: $180.94 (37%)
ADD TO CART
Product Specifications
- Other Name: Damper, Engine Crankshaft And Camshaft Balancer; Balancer, Engine Crankshaft And Camshaft Balancer
- Replaced by: 19540389
- Replaces: 12662602, 12674750, 12702612, 12651599, 19433088, 98062792
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2016 GMC Savana 2500 | Base | 8 Cyl 6.6 L DIESEL
View related parts
GMC Savana 2500 Vibration Damper
Part Number: 97374383
$809.93 MSRP: $1280.12
You Save: $470.19 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Balancer Assembly-Crankshaft (W/Pulley); Balancer, Engine Crankshaft Pulley And Balancer
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2010 GMC Savana 2500 | Base | 8 Cyl 6.6 L DIESEL
View related parts
GMC Savana 2500 Vibration Damper
Part Number: 19417972
$409.58 MSRP: $650.30
You Save: $240.72 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Balancer (Remanufacture); Harmonic Balancer; Balance Shaft; Balancer Shaft Kit; Engine Crankshaft and Camshaft Balancer.
- Replaces: 10224538
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-2006 GMC Savana 2500 | Base, SLE, SLT | 6 Cyl 4.3 L GAS
View related parts
GMC Savana 2500 Crankshaft Pulley
Part Number: 12680364
$84.19 MSRP: $131.85
You Save: $47.66 (37%)
ADD TO CART
Product Specifications
- Other Name: Pulley; Harmonic Balancer Puller; Harmonic Balancer; Vibration Damper; Balancer, Engine Crankshaft And Camshaft Balancer
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2024 GMC Savana 2500 | Base, LS, LT | 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 6.6 L GAS
View related parts
GMC Savana 2500 Balance Shaft
Part Number: 12653449
$134.96 MSRP: $212.35
You Save: $77.39 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Balancer, Engine Crankshaft And Camshaft Balancer; Balance Shaft Assembly; Plate, Engine Camshaft & Balance Shaft Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2023 GMC Savana 2500 | Base, LS, LT | 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS
View related parts
GMC Savana 2500 Vibration Damper
Part Number: 12625430
$71.10 MSRP: $111.35
You Save: $40.25 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Balancer, Engine Crankshaft And Camshaft Balancer; Harmonic Balancer; Balancer
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017-2022 GMC Savana 2500 | Base, LS, LT | 4 Cyl 2.8 L DIESEL
View related parts
GMC Savana 2500 Vibration Damper
Part Number: 10243272
$222.51 MSRP: $350.10
You Save: $127.59 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulley; Balancer, Engine Crankshaft And Camshaft Balancer
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-2002 GMC Savana 2500 | Base, SLE, SLT | 8 Cyl 5.0 L GAS
View related parts
GMC Savana 2500 Vibration Damper
Part Number: 12634105
Product Specifications
- Other Name: Pulley; Harmonic Balancer; Crankshaft Balance; Balancer
- Replaces: 12576652, 12553112
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2017 GMC Savana 2500 | Base, LS, LT, SLE | 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS
View related parts
GMC Savana 2500 Vibration Damper
Part Number: 10154688
Product Specifications
- Other Name: Balancer, Crankshaft; Balancer, Engine Crankshaft And Camshaft Balancer; Balancer, Engine Crankshaft
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-2002 GMC Savana 2500 | Base, SLE, SLT | 8 Cyl 6.5 L DIESEL

GMC Savana 2500 Harmonic Balancer

Our website offers an extensive catalog of genuine GMC Savana 2500 Harmonic Balancer at unbeatable prices. Every OEM GMC Savana 2500 Harmonic Balancer comes with a manufacturer's warranty, an easy return policy, and rapid delivery service. Don't miss out on this great opportunity!

GMC Savana 2500 Harmonic Balancer Parts Questions & Experts Answers

Vibration Damper
10224885
Q: How to replace the harmonic balancer on GMC Savana 2500?
A: The first step to replace a crankshaft balancer involves removing either the air conditioning belt when there is one or the accessory belt if there is no air conditioning system. Beginning by removing the Starter motor and lower Fan Shroud the technician should check that the Flywheel holding tool (J 42386-A) establishes tooth engagement with the engine Flywheel. Use one m10-1.5 x 120 mm bolt and one m10-1.5 x 45 mm bolt to fasten the j 42386-a before tightening them to 50 nm (37 ft. Lbs.). The bolt securing the crankshaft balancer needs removal for later reuse during the installation process. The crankshaft balancer remover (J 41816) combined with the crankshaft end protector (J 41816-2) allows you to remove the crankshaft balancer after cleaning and inspecting it. Then install the crankshaft balancer by aligning it directly on the crankshaft followed by the use of crankshaft balancer and sprocket installer (J 41665). Use the threaded rod along with its nut and washer along with the installer to start installation at the front end of the balancer. Hold the threaded rod hex section using a wrench while turning the installation tool nut clockwise with another wrench until the first part of crankshaft installation completes. Use the installation tool to drive the bigger end of the balancer against the front section until the complete installation is achieved. The previous crankshaft balancer bolt should be installed before tightening it to 330 nm (240 ft. Lbs.). Next remove the bolt. Measure the installation position of the balancer again; if necessary use the j 41665 to reinstall correctly. You should use a new crankshaft balancer bolt which requires an initial torque of 50 nm (37 ft. Lbs.) followed by the 140 degrees setting measured with the torque angle meter (J 36660-A). The procedure completes with Starter motor installation followed by lower Fan Shroud adjunction along with accessory Drive Belt installation unless a/c is present and its Drive Belt installation until executing the crankshaft position learn sequence.