How to replace the rear door moldings on GMC Sonoma?

The tools needed to replace the GMC Utility's rear door body side molding include: Heat Gun (J 25070) together with 3M(TM) scotch brite molding adhesive remover disk (3M(TM) P/N 07501). Two tools will be necessary: Heat Gun (J 25070) and 3M(TM) scotch brite molding adhesive remover disk (3M(TM) P/N 07501). Start the door molding removal process by unscrewing two bottom screws from each door's lower edge. Use the Heat Gun (J 25070) to heat the door side molding at a distance of about 152 mm (6 in) while rotating it in circular motions for 30 seconds. Apply this heat technique while carefully avoiding any contact that might scratch or chip the paint. Use a flat-bladed tool to extract the door side molding from the panel surface while pushing the molding clip back through the body panel from inside. Then remove the molding from its retainer plate. Use the 3M(TM) scotch brite molding adhesive remover disk (3M(TM) P/N 07501) to remove all adhesive from the body panel and the door side molding back while cleaning the body panel with Varnish Makers and Painters (VMP) naphtha. Start body panel installation by cleaning the tape contact area and drying the painted surface while preheating the panel using a heat lamp or heat gun until it reaches 21°C (70°F). Insert the horizontal upper flange of each door molding toward the center of the retainer plate until its top flange locks into the retainer's top channel. Installation requires backer removal from the door side molding front section while you press the body during alignment of molding clips with body holes. Secure in place with two screws threaded through door hem holes into lower corner bosses of the molding. Then hand-roll the door side molding onto the body to achieve proper attachment.

OEM GMC Sonoma Door Moldings

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

29 Door Moldings found

View related parts
GMC Sonoma Body Side Molding, Outer Part Number: 15761413
$109.78 MSRP: $129.48
You Save: $19.70 (16%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Molding, Cab And Load Carrier Outer Side Decoration; Door Moldings
- Position: Outer
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2004 GMC Sonoma | SL, SLS | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
GMC Sonoma Body Side Molding, Outer Passenger Side Part Number: 12543920
Product Specifications
- Other Name: Molding, Cab And Load Carrier Outer Side Decoration; Door Moldings
- Position: Outer Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1997 GMC Sonoma | SLE, SLS | 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
GMC Sonoma Rear Molding, Outer Driver Side Part Number: 12543927
Product Specifications
- Other Name: Molding, Cab And Load Carrier Outer Side Decoration
- Position: Outer Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1995 GMC Sonoma | SL, SLE, SLS | 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
GMC Sonoma Rear Molding, Outer Passenger Side Part Number: 12543928
Product Specifications
- Other Name: Molding, Cab And Load Carrier Outer Side Decoration
- Position: Outer Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1995 GMC Sonoma | SL, SLE, SLS | 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
GMC Sonoma Rear Molding, Outer Passenger Side Part Number: 12543926
Product Specifications
- Other Name: Molding, Cab And Load Carrier Outer Side Decoration
- Position: Outer Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1997 GMC Sonoma | SL, SLE, SLS | 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
GMC Sonoma Rear Molding, Outer Driver Side Part Number: 12543925
Product Specifications
- Other Name: Molding, Cab And Load Carrier Outer Side Decoration
- Position: Outer Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1997 GMC Sonoma | SL, SLE, SLS | 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
GMC Sonoma Body Side Molding, Outer Driver Side Part Number: 12543919
Product Specifications
- Other Name: Molding, Cab And Load Carrier Outer Side Decoration; Door Moldings
- Position: Outer Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1997 GMC Sonoma | SLE, SLS | 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
GMC Sonoma Body Side Molding, Front Lower Driver Side Part Number: 12376673
Product Specifications
- Other Name: Molding, Front Side Door Lower; Door Moldings; Molding, Cab And Load Carrier Outer Side Decoration
- Position: Front Lower Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2001 GMC Sonoma | SL, SLE, SLS | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
GMC Sonoma Body Side Molding, Front Lower Passenger Side Part Number: 12376674
Product Specifications
- Other Name: Molding, Front Side Door Lower; Door Moldings; Molding, Cab And Load Carrier Outer Side Decoration
- Position: Front Lower Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2001 GMC Sonoma | SL, SLE, SLS | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
GMC Sonoma Body Side Molding, Front Part Number: 15768344
Product Specifications
- Other Name: Molding, Front Side Door; Door Moldings; Molding, Cab And Load Carrier Outer Side Decoration
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2003 GMC Sonoma | SLS | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
GMC Sonoma Body Side Molding, Front Lower Passenger Side Part Number: 12386648
Product Specifications
- Other Name: Molding, Front Side Door Lower; Door Moldings; Molding, Cab And Load Carrier Outer Side Decoration
- Position: Front Lower Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1997 GMC Sonoma | SL, SLE, SLS | 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
GMC Sonoma Body Side Molding, Front Lower Driver Side Part Number: 12386647
Product Specifications
- Other Name: Molding, Front Side Door Lower; Door Moldings; Molding, Cab And Load Carrier Outer Side Decoration
- Position: Front Lower Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1997 GMC Sonoma | SL, SLE, SLS | 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
GMC Sonoma Lower Molding, Rear Part Number: 12376677
Product Specifications
- Other Name: Molding, End Gate And Rear Door Decoration; Molding
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2001 GMC Sonoma | SL, SLE, SLS | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
GMC Sonoma Body Side Molding, Outer Passenger Side Part Number: 15958442
Product Specifications
- Other Name: Molding, Cab And Load Carrier Outer Side Decoration; Door Moldings
- Position: Outer Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993 GMC Sonoma | Base, SLE, SLS | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
GMC Sonoma Side Panel, Driver Side Part Number: 15668793
Product Specifications
- Other Name: Molding, Body Interior Trim
- Position: Driver Side
- Replaces: 15668799
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2002 GMC Sonoma | SLS | 4 Cyl 2.2 L FLEX, 6 Cyl 4.3 L GAS
View related parts
GMC Sonoma Rear Molding, Passenger Side Part Number: 15954056
Product Specifications
- Other Name: Molding A; Molding, Cab And Load Carrier Outer Side Decoration
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993 GMC Sonoma | Base, SLE, SLS | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
GMC Sonoma Body Side Molding, Rear Lower Part Number: 15990273
Product Specifications
- Other Name: Molding; Door Moldings; Molding, Cab And Load Carrier Outer Side Decoration
- Position: Rear Lower
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-1997 GMC Sonoma | SLE, SLS | 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
GMC Sonoma Upper Molding, Passenger Side Part Number: 14058022
Product Specifications
- Other Name: Molding, Door Trim Panel
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 GMC Sonoma | Base, GT, SLE, SLS | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
GMC Sonoma Upper Molding, Driver Side Part Number: 14058021
Product Specifications
- Other Name: Molding, Door Trim Panel
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 GMC Sonoma | Base, GT, SLE, SLS | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
GMC Sonoma Side Molding, Front Driver Side Part Number: 15630001
Product Specifications
- Other Name: Molding, Front Fender And Body Ornamentation; Molding; Molding, Cab And Load Carrier Outer Side Decoration
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 GMC Sonoma | Base, GT, SLE, SLS | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS

| Page 1 of 2 |Next >

1-20 of 29 Results

GMC Sonoma Door Moldings

Want to cut long-term maintenance and repair costs? Choose OEM Door Moldings. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine GMC Sonoma parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM GMC Sonoma Door Moldings includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Door Moldings are parts that add value on look and steadiness of the GMC Sonoma, which is a famous compact pickup truck designed for powerful and lasting performance. These Door Moldings have been and are intended for some Sonoma models manufactured between 1982 and 2005, and they have several important functions, such as a protection of side doors against various impacts, as well as an increase of car's efficiency. The types of the Door Moldings include side moldings, door edge guards, belt moldings, and rocker panel moldings, which is a customized product to achieve the desired need and easy installation with pre-applied 3M acrylic foam tape. These interiors not only add to the looks of the truck but also add protection to the sheets from wear and tear thus playing a part in safety. The GMC Sonoma has gained its reputation regarding its reliability, and the addition of high-quality Door Moldings adds to it. The Door Moldings are collectible additions to the automotive parts primarily because of the Door Moldings features which enhance style or form and function, protection or substance. Due to compatibility with different Sonoma models, their owners can keep the cars' integrities and appearances intact, so these Door Moldings are a valuable asset for any GMC Sonoma lover.

GMC Sonoma Door Moldings Parts and Q&A

Body Side Molding, Outer
15761413
Q: How to replace the rear door moldings on GMC Sonoma?
A:
The tools needed to replace the GMC Utility's rear door body side molding include: Heat Gun (J 25070) together with 3M(TM) scotch brite molding adhesive remover disk (3M(TM) P/N 07501). Two tools will be necessary: Heat Gun (J 25070) and 3M(TM) scotch brite molding adhesive remover disk (3M(TM) P/N 07501). Start the door molding removal process by unscrewing two bottom screws from each door's lower edge. Use the Heat Gun (J 25070) to heat the door side molding at a distance of about 152 mm (6 in) while rotating it in circular motions for 30 seconds. Apply this heat technique while carefully avoiding any contact that might scratch or chip the paint. Use a flat-bladed tool to extract the door side molding from the panel surface while pushing the molding clip back through the body panel from inside. Then remove the molding from its retainer plate. Use the 3M(TM) scotch brite molding adhesive remover disk (3M(TM) P/N 07501) to remove all adhesive from the body panel and the door side molding back while cleaning the body panel with Varnish Makers and Painters (VMP) naphtha. Start body panel installation by cleaning the tape contact area and drying the painted surface while preheating the panel using a heat lamp or heat gun until it reaches 21°C (70°F). Insert the horizontal upper flange of each door molding toward the center of the retainer plate until its top flange locks into the retainer's top channel. Installation requires backer removal from the door side molding front section while you press the body during alignment of molding clips with body holes. Secure in place with two screws threaded through door hem holes into lower corner bosses of the molding. Then hand-roll the door side molding onto the body to achieve proper attachment.