How to replace the torsion bar on GMC Yukon XL 1500?

To change the Torsion Bar, one must lift and support the vehicle. Mount the Torsion Bar unloading/loadingtool(J 36202) to the adjustment arm and crossmember and tighten the tension on the arm till pressure is taken off the adjustment bolt and the adjuster bolt. Mark the adjustment bolt and note the number of turns necessitated for removal. Then, one needs to disconnect the adjustment bolt and the adjuster nut then adjustment bolt and adjuster nut for k25/35 series of mw3, c5f, and cop (MT1). Pull the j 36202 out so that the Torsion Bar is unloaded and move the Torsion Bar forward to clear the adjustment arm holding it with your hand. Unbolt the Torsion Bar crossmember bolts from the weld nuts from the upper link mounting nuts and bolts for the k25/35 series with mt1, mw3, c5f, and cop. Make a note of where the torsion bars are situated because the left and right bars are different and then pull the torsion bars from the vehicle. For installation, the torsion bars are mounted on the lower Control Arm, and the Torsion Bar crossmember installed. Install the Torsion Bar crossmember bolts to the weld nuts and bring them to the required torques of 95 nm (70 ft. Lbs). Then mount the upper link mounting nuts and bolts for the k 25/35 series with mt1, mw3 c5f, and cop, tightening the nut to 95 nm 70 ft. Lbs. While supporting the adjustment arm, slide the Torsion Bar to the rear until it engages the adjustment arm completely and then re-install the j 36202 to the adjustment arm as well as to the crossmember. Tighten the adjustment arm to load the Torsion Bar, making sure the adjustment bolt goes in with the same number of turns taken in removal. Lastly, thread the adjustment bolt and the adjuster nut , then the adjustment bolt and the adjuster nut with the k 25/35 series with mt1, mw3, c5f & cop. Remove the j 36202 and let the adjustment bolt take up the tension of the Torsion Bar and then remove the safety stands lowering the vehicle and measure the z height, adjust the adjustment bolt as necessary to obtain the desired height.

OEM GMC Yukon XL 1500 Torsion Bar

Suspension Torsion Bar

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Torsion Bars found

View related parts
GMC Yukon XL 1500 Torsion Bar, Front Driver Side
Part Number: 19330060
$286.89 MSRP: $451.40
You Save: $164.51 (37%)
ADD TO CART
Product Specifications
- Other Name: Bar, Front Torsion; Ball Joint; Lower Ball Joint; Bar, Front Chassis
- Position: Front Driver Side
- Replaces: 15528965
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2013 GMC Yukon XL 1500 | Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon XL 1500 Torsion Bar, Front Passenger Side
Part Number: 19330059
$286.89 MSRP: $451.40
You Save: $164.51 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Front Torsion; Ball Joint; Lower Ball Joint; Bar, Front Chassis
- Position: Front Passenger Side
- Replaces: 15528966
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2013 GMC Yukon XL 1500 | Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon XL 1500 Torsion Bar, Front Driver Side
Part Number: 19330058
$286.95 MSRP: $451.49
You Save: $164.54 (37%)
ADD TO CART
Product Specifications
- Other Name: Bar, Front Torsion; Bar, Front Chassis
- Position: Front Driver Side
- Replaces: 15528963
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2013, 2000 GMC Yukon XL 1500 | Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon XL 1500 Torsion Bar, Front Passenger Side
Part Number: 19330057
$286.95 MSRP: $451.49
You Save: $164.54 (37%)
ADD TO CART
Product Specifications
- Other Name: Bar, Front Torsion; Bar, Front Chassis
- Position: Front Passenger Side
- Replaces: 15528964
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2013, 2000 GMC Yukon XL 1500 | Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon XL 1500 Torsion Bar, Front
Part Number: 15048312
$257.64 MSRP: $405.40
You Save: $147.76 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bar, Front Torsion
- Position: Front
- Replaced by: 19332932
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 GMC Yukon XL 1500 | SLE, SLT | 8 Cyl 5.3 L GAS
View related parts
GMC Yukon XL 1500 Torsion Bar, Front Passenger Side
Part Number: 19332928
Product Specifications
- Other Name: Bar, Front Torsion; Bar, Front Chassis
- Position: Front Passenger Side
- Replaces: 15048308
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2006 GMC Yukon XL 1500 | Denali, SL, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon XL 1500 Torsion Bar, Front Driver Side
Part Number: 19332927
Product Specifications
- Other Name: Bar, Front Torsion; Bar, Front Chassis
- Position: Front Driver Side
- Replaces: 15048307
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2006 GMC Yukon XL 1500 | Denali, SL, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon XL 1500 Torsion Bar, Front Passenger Side
Part Number: 19332946
$257.82 MSRP: $405.67
You Save: $147.85 (37%)
Product Specifications
- Other Name: Bar, Front Torsion; Bar, Front Chassis
- Position: Front Passenger Side
- Replaces: 15528958
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2013 GMC Yukon XL 1500 | Denali, SL, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon XL 1500 Torsion Bar, Front Driver Side
Part Number: 19332945
$257.82 MSRP: $405.67
You Save: $147.85 (37%)
Product Specifications
- Other Name: Bar, Front Torsion; Bar, Front Chassis
- Position: Front Driver Side
- Replaces: 15528957
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2013 GMC Yukon XL 1500 | Denali, SL, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon XL 1500 Torsion Bar, Front
Part Number: 19332931
Product Specifications
- Other Name: Bar, Front Torsion; Bar, Front Chassis
- Position: Front
- Replaces: 15048311
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 GMC Yukon XL 1500 | SLE, SLT | 8 Cyl 5.3 L GAS
View related parts
GMC Yukon XL 1500 Torsion Bar, Front Passenger Side
Part Number: 15051908
Product Specifications
- Other Name: Bar-Front Torsion (Right-Hand); Bar, Front Chassis
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2006 GMC Yukon XL 1500 | SL, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
GMC Yukon XL 1500 Torsion Bar, Front Driver Side
Part Number: 15051907
Product Specifications
- Other Name: Bar-Front Torsion (Left-Hand); Bar, Front Chassis
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2006 GMC Yukon XL 1500 | SL, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS

GMC Yukon XL 1500 Torsion Bar

Our website offers an extensive catalog of genuine GMC Yukon XL 1500 Torsion Bar at unbeatable prices. Every OEM GMC Yukon XL 1500 Torsion Bar comes with a manufacturer's warranty, an easy return policy, and rapid delivery service. Don't miss out on this great opportunity!

GMC Yukon XL 1500 Torsion Bar Parts Questions & Experts Answers

Torsion Bar, Front Passenger Side
19332946
Q: How to replace the torsion bar on GMC Yukon XL 1500?
A: To change the Torsion Bar, one must lift and support the vehicle. Mount the Torsion Bar unloading/loadingtool(J 36202) to the adjustment arm and crossmember and tighten the tension on the arm till pressure is taken off the adjustment bolt and the adjuster bolt. Mark the adjustment bolt and note the number of turns necessitated for removal. Then, one needs to disconnect the adjustment bolt and the adjuster nut then adjustment bolt and adjuster nut for k25/35 series of mw3, c5f, and cop (MT1). Pull the j 36202 out so that the Torsion Bar is unloaded and move the Torsion Bar forward to clear the adjustment arm holding it with your hand. Unbolt the Torsion Bar crossmember bolts from the weld nuts from the upper link mounting nuts and bolts for the k25/35 series with mt1, mw3, c5f, and cop. Make a note of where the torsion bars are situated because the left and right bars are different and then pull the torsion bars from the vehicle. For installation, the torsion bars are mounted on the lower Control Arm, and the Torsion Bar crossmember installed. Install the Torsion Bar crossmember bolts to the weld nuts and bring them to the required torques of 95 nm (70 ft. Lbs). Then mount the upper link mounting nuts and bolts for the k 25/35 series with mt1, mw3 c5f, and cop, tightening the nut to 95 nm 70 ft. Lbs. While supporting the adjustment arm, slide the Torsion Bar to the rear until it engages the adjustment arm completely and then re-install the j 36202 to the adjustment arm as well as to the crossmember. Tighten the adjustment arm to load the Torsion Bar, making sure the adjustment bolt goes in with the same number of turns taken in removal. Lastly, thread the adjustment bolt and the adjuster nut , then the adjustment bolt and the adjuster nut with the k 25/35 series with mt1, mw3, c5f & cop. Remove the j 36202 and let the adjustment bolt take up the tension of the Torsion Bar and then remove the safety stands lowering the vehicle and measure the z height, adjust the adjustment bolt as necessary to obtain the desired height.

Related GMC Yukon XL 1500 Parts

Browse GMC Yukon XL 1500 Torsion Bar by Years

2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 2003 2002 2001 2000