Make sure this part fits

GM 15279196
Rear Mount Bracket

2006-2011 GM

Customer Questions & Expert Answers (20)
GM 15279196 Rear Mount Bracket
  • Part Description
    Bracket, Engine Mounting; Engine Mount Torque Strut; Engine Mount Bracket; Engine Torque Mount; Motor Mount
  • Position
    Rear
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2006-2011 Buick LucerneCXL, CXS, Super8 Cyl 4.6 L GAS
    2006-2011 Cadillac DTSBase, Livery, Luxury, Platinum, Premium8 Cyl 4.6 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 15279196 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 15279196 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the rear engine mount bracket on Buick Lucerne? Posted by Customer
    A:
    The procedure to replace the rear Engine Mount Bracket begins with the removal of the Engine Mount until the Engine Mount Bracket bolts can be removed to finally remove the Engine Mount Bracket itself. Position the Engine Mount Bracket to the transaxle after following the fastener notice and install the Engine Mount Bracket bolts at 50 nm (37 ft. Lbs. Torque). Finally, install the Engine Mount.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the right engine mount bracket on Cadillac DTS? Posted by Customer
    A:
    The correct procedure to replace the right Engine Mount Bracket includes removing the right Engine Mount followed by detaching the right Engine Mount Bracket from the engine stud and transaxle bolts before you remove the right mount bracket. The procedure for right Engine Mount Bracket installation involves setting it properly in place on the engine block while also securing transaxle bolts loosely at first. Fastener attachment must be performed with attention to vehicle protection before installing the right Engine Mount Bracket onto both engine stud and bolts/stud while tightening with 73 nm (54 lb ft) torque. The right Engine Mount installation process concludes with its reinstallation.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the final step in the process for the 2006 Buick Lucerne? Posted by Customer
    A:
    Finally, install the engine mount.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What is the first step to replace the engine front mount for the 2008 Buick Lucerne? Posted by Customer
    A:
    Remove the front air deflector.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What should be done after all installations are complete for the 2006 Buick Lucerne? Posted by Customer
    A:
    Remove the adjustable jack and block of wood from under the transaxle oil pan and reinstall the right front wheel and tire.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What is the final step in the process for the 2007 Buick Lucerne? Posted by Customer
    A:
    Finally, install the engine mount.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What is the first step to replace the engine rear mount for the 2007 Buick Lucerne? Posted by Customer
    A:
    Remove the right front wheel and tire.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What is the torque specification for the engine mount to bracket nut for the 2007 Buick Lucerne? Posted by Customer
    A:
    80 N.m (59 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What should be done with the lower engine mount bracket to engine stud nuts for the 2009 Cadillac DTS? Posted by Customer
    A:
    Tighten them to the same torque specification of 50 Nm (37 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What is the next step after inserting the front engine mount stud for the 2006 Cadillac DTS? Posted by Customer
    A:
    Install the front engine mount to engine mount bracket nut and tighten it to 80 Nm (59 ft. lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What is the next step after positioning the right engine mount bracket for the 2010 Cadillac DTS? Posted by Customer
    A:
    Secure the right engine mount bracket to the engine stud and tighten the bolts/stud to 73 Nm (54 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What should be done after removing the engine mount bracket for the 2008 Cadillac DTS? Posted by Customer
    A:
    Take off the front engine mount to engine mount bracket nut and then remove the front engine mount.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What should be removed after the engine mount bracket for the 2010 Cadillac DTS? Posted by Customer
    A:
    Remove the front engine mount to engine mount bracket nut.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What is the first step to replace the right engine mount for the 2009 Cadillac DTS? Posted by Customer
    A:
    Remove the frame.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What is the next step after removing the bolts for the 2007 Cadillac DTS? Posted by Customer
    A:
    Take out the right engine mount bracket.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    How do you install the right engine mount bracket for the 2008 Cadillac DTS? Posted by Customer
    A:
    Position the right engine mount bracket correctly onto the engine block and transaxle, securing the transaxle bolts finger tight.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What is the next step after attaching the front engine mount bracket for the 2007 Cadillac DTS? Posted by Customer
    A:
    Install the front engine mount to engine mount bracket nut and tighten it to 80 N.m (59 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What is the torque specification for the transaxle brace bolt for the 2006 Cadillac DTS? Posted by Customer
    A:
    Tighten it to 50 Nm (37 ft. lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What should be done after removing the engine mount bracket for the 2009 Cadillac DTS? Posted by Customer
    A:
    Take off the front engine mount to engine mount bracket nut and then remove the front engine mount.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Rear Mount Bracket 15279196 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 15279196 Rear Mount Bracket is available in the market under the name GM Engine Mount, Engine Mount Bracket. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 15279196 Rear Mount Bracket fits certain Cadillac DTS models, as well as Buick Lucerne models.
The original GM component designated by manufacturer part number 15279196 maintains top performance when functioning as the Bracket, Engine Mounting; Engine Mount Torque Strut; Engine Mount Bracket; Engine Torque Mount; Motor Mount unit at its Rear. The component 15279196 is constructed from durable material and its dimensions span 4.7 x 3.5 x 10.9 inches while weighing 2.90 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. The part 15279196 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.