Menu
×
Search Bar
Search by Part Number, Part Name, or Vehicle
My Garage
Cart
Help Center Contact Us
Make sure this part fits

GM 10412924
Lower Control Arm Bushing

2001-2007 GM

Customer Questions & Expert Answers (18)
GM 10412924 Lower Control Arm Bushing
  • Part Description
    Bushing; Axle Support Bushing; Control Arm Bushing; Crossmember Bushing; Axle Pivot Bushing; Axle Beam Mount
  • Position
    Rear Lower
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits

  • 10412924 Lower Control Arm Bushing is Ref No. 8 in the diagram below

    2004 Oldsmobile Silhouette Lower Control Arm Bushing Diagram for 10412924
    The diagram listed above is for your reference. View diagram for your vehicle

    Related Parts for 10412924

  • Vehicle Fitment

    Year Make Model Trim Engine
    2002-2007 Buick RendezvousCX, CX Plus, CXL, CXL Plus, Ultra6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
    2005-2007 Buick TerrazaCX, CXL6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
    2005-2006 Chevrolet UplanderBase, LS, LT6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
    2002-2005 Chevrolet VentureBase, LS, LT, Plus, Value, Warner Bros.6 Cyl 3.4 L GAS
    2002-2004 Oldsmobile SilhouetteGL, GLS, Premiere6 Cyl 3.4 L GAS
    2001-2005 Pontiac AztekBase, GT, Rally6 Cyl 3.4 L GAS
    2002-2006 Pontiac MontanaBase, SV66 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
    2005-2007 Saturn Relay1, 2, 36 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
    Warning: California's Proposition 65

  • Customer Questions & Expert Answers

    Q:
    Is this 10412924 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 10412924 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the rear axle lower control arm bushing on Buick Rendezvous? Posted by Customer
    A:
    Begin the rear axle lower Control Arm bushing replacement by supporting the vehicle above the floor then remove both wheels along with their respective tires. You need to use a utility stand for supporting the lower Control Arm before removing the coil spring. Note a mark on the lower Control Arm at its cam indicator position before you detach mounting bolts between the lower Control Arm and crossmember (1, 5). The orientation of voids within the bushing relative to the crossmember must be recognized before moving the bushing out from its position in the crossmember. The Control Arm bushing set (J 21474-01) comes equipped with the following tools for this process: j-6627-4 , lower Control Arm bushing receiver (J 45411) along with j-21474-8 and j-21474-4 . The necessary tools include j-6627-4 , lower Control Arm bushing receiver (J 45411) , j-21474-8 , and j-21474-4 . When installing the bushing place it in an identical position as before while maintaining proper alignment of voids. The Control Arm bushing set (J 21474-01) guides the bushing installation on the crossmember which is followed by reinstallation of the lower Control Arm backed by mounting bolts (1, 5) with the lower Control Arm mark positioned at the cam indicator. Complete the coil spring installation next then reinstall both tire and wheel assemblies. After inspecting the rear camber and toe angles perform any necessary adjustments before lowering the vehicle.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the control arm bushing in the rear suspension on Buick Terraza? Posted by Customer
    A:
    First, to replace the Control Arm bushing in the rear suspension, one should raise and support the vehicle. Apply a gesture where you support the Control Arm in front of the coil spring using a utility stand, then take off the bolts of the Control Arm from the rear axle. Drop the rear axle using the utility stand to get access to the Control Arm bushing, placing a mark indicating its orientation in the lower Control Arm. Make use of the j 28685 rear suspension bushing remover/installer and the j 9519-e ball joint remover/installer kit in dislodging the Control Arm bushing. For installation, set the flat edge of the new bushing to be 90 deg to the fluid axis which is 9 deg from the center line of Control Arm. Again, using j 28685 and the j 9519-e install the Control Arm bushing that extends 30mm (1.18in) from the Control Arm. It is rightly established when its extreme puts in display to the line indicator on the j 28685. Lift the rear axle with the utility stand reinstall the Control Arm Bolt at the rear axle, take off utility stand then put the vehicle down.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the final step after installing the bushing for the 2002 Buick Rendezvous? Posted by Customer
    A:
    Disassemble the tools and install the lower control arm.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm Bushing
    Q:
    How should the control arm be supported for the 2006 Buick Terraza? Posted by Customer
    A:
    Use a utility stand to support the control arm forward of the coil spring.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm Bushing
    Q:
    What is the next step after removing the control arm bolts for the 2003 Buick Rendezvous? Posted by Customer
    A:
    Lower the rear axle with the utility stand to access the control arm bushing.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm Bushing
    Q:
    What should be done after installing the bushing to the crossmember for the 2005 Buick Rendezvous? Posted by Customer
    A:
    Reinstall the lower control arm and mounting bolts (1, 5) to the crossmember, aligning the mark on the lower control arm at the cam indicator.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm Bushing
    Q:
    How do you remove the bushing from the control arm for the 2004 Buick Rendezvous? Posted by Customer
    A:
    Tighten the bushing tool (J21474-4) until the bushing is removed from the control arm, then disassemble the tools.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm Bushing
    Q:
    What should you do after removing the bushing for the 2006 Buick Rendezvous? Posted by Customer
    A:
    Disassemble the bushing tools.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm Bushing
    Q:
    What tools are needed to remove the bushing from the crossmember for the 2007 Buick Rendezvous? Posted by Customer
    A:
    Use the following tools from the Control Arm Bushing Set (J 21474-01): J-6627-4, Lower Control Arm Bushing Receiver (J 45411), J-21474-8, and J-21474-4.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm Bushing
    Q:
    What should be done after inserting the bushing into the control arm for the 2007 Buick Terraza? Posted by Customer
    A:
    Apply J 23444-A to the threads of the Puller Bolt Thrust Bearing (J 21474-27).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm Bushing
    Q:
    What tools are included in the bushing removal assembly for the 2005 Buick Terraza? Posted by Customer
    A:
    Puller Bolt Thrust Bearing (J 21474-27), Control Arm Bushing Installer (J 21474), Sprocket Bearing Remover (J 34126), Front Knuckle Support (J 35379), Bushing Installer Remover (J 21474-2), and 1/2 Inch Nut (J 21474-4).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm Bushing
    Q:
    What is the first step to replace the control arm bushing for the 2002 Chevrolet Venture? Posted by Customer
    A:
    First raise and support the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm Bushing
    Q:
    What is the first step to replace the rear axle lower control arm bushing for the 2005 Chevrolet Uplander? Posted by Customer
    A:
    First, remove the lower control arm, ensuring to identify the orientation of the voids in the bushing relative to the crossmember.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm Bushing
    Q:
    What should be done after positioning the new bushing for the 2004 Chevrolet Venture? Posted by Customer
    A:
    Use the Control Arm Bushing Set (J 21474-O1) to install the bushing to the crossmember before reinstalling the lower control arm.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm Bushing
    Q:
    What should be used to install the bushing to the crossmember for the 2006 Chevrolet Uplander? Posted by Customer
    A:
    Use the Control Arm Bushing Set (J 21474-01) to install the bushing to the crossmember.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm Bushing
    Q:
    What tools are included in the bushing removal assembly for the 2003 Chevrolet Venture? Posted by Customer
    A:
    Puller Bolt (J 21474-27), Control Arm Bushing Installer (J 21474), Driven Sprocket Support Bearing Installer (J 34126), Front Knuckle Support (J 35379), Bushing Installer (J 21474-2), and Nut (J 21474-4).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm Bushing
    Q:
    What tools are required to remove the control arm bushing for the 2005 Chevrolet Venture? Posted by Customer
    A:
    The J 28685 Rear Suspension Bushing Remover/Installer and the J 9519-E Ball Joint Remover/Installer Kit are required.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Control Arm Bushing
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Lower Control Arm Bushing 10412924 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 10412924 Lower Control Arm Bushing is available in the market under the name GM Control Arm Bushing, Trailing Arm Bushing, Axle Beam Mount. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 10412924 Lower Control Arm Bushing fits certain Chevrolet Uplander, Venture models, as well as Buick Rendezvous, Terraza. Additionally, it is compatible with Pontiac Aztek, Montana and Oldsmobile Silhouette models.
The original GM component designated by manufacturer part number 10412924 maintains top performance when functioning as the Bushing; Axle Support Bushing; Control Arm Bushing; Crossmember Bushing; Axle Pivot Bushing; Axle Beam Mount unit at its Rear Lower. The component 10412924 is constructed from durable material and its dimensions span 3.6 x 3.0 x 2.7 inches while weighing 0.70 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Suspension Crossmember Bushing; Bushings; Bushing, Rear Axle Support And Control Arm; Bushing, Rear Axle Control Arm. The part 10412924 has available replacement options. Each vehicle needs 2 units of the part marked as SKU 10412924. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.