Menu
×
Search Bar
Search by Part Number, Part Name, or Vehicle
My Garage
Cart
Help Center Contact Us
Make sure this part fits

GM 12221452
Control Module

2001-2003 GM

Customer Questions & Expert Answers (4)
GM 12221452 Control Module
  • Part Description
    Module Assembly, Electronic Brake & Traction Control; ABS Control Module
  • Replaced By
    18078147
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits

  • 12221452 Control Module is Ref No. 2 in the diagram below

    2002 Chevy Monte Carlo Control Module Diagram for 12221452
    The diagram listed above is for your reference. View diagram for your vehicle

    Related Parts for 12221452

  • Vehicle Fitment

    Year Make Model Trim Engine
    2003, 2001 Chevrolet ImpalaBase, LS, LS Sport6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
    2001-2003 Chevrolet Monte CarloLS, LS Competition, LS Sport6 Cyl 3.4 L GAS
    Warning: California's Proposition 65

  • Customer Questions & Expert Answers

    Q:
    Is this 12221452 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 12221452 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the ABS Control Module on Chevrolet Monte Carlo? Posted by Customer
    A:
    The process of ABS Control Module replacement starts by verifying the Ignition Switch is set to off to avoid harming equipment. Start by removing the red locking tab from the connector lock tab then press down on the lock tab to expose the sliding connector cover for disconnecting the ABS Control Module harness connector. The assembly removal procedure requires cleaning all dirt but avoids using tools to pry parts or damaging bpmv surfaces or solenoid valves. Hover the ABS Control Module away from the bpmv by gently pulling on its end after screw removal of the 4 screws which connect them. To install the ABS Control Module you should first use a clean rag to clean the bpmv surface with alcohol and then place the ABS Control Module on the bpmv and fasten it with the 4 screws until they reach 5 nm (44 inch lbs.). Reconnect the ABS Control Module harness connector after pushing the lock tab and install the sliding connector cover back to the locked position then return the red locking tab. Complete the diagnostic system check - abs after setting the Ignition Switch to run with no engine start followed by the installation steps.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be done after installing the brake pipes on the BPMV for the 2003 Chevrolet Impala? Posted by Customer
    A:
    Tighten all fittings to the same torque.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar ABS Control Module
    Q:
    How do you install the master cylinder brake pipes into the BPMV for the 2001 Chevrolet Impala? Posted by Customer
    A:
    Install the master cylinder brake pipes into the BPMV, tightening the fittings to 24 Nm (18 ft. lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar ABS Control Module
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Control Module 12221452 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 12221452 Control Module is available in the market under the name GM ABS Control Module. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 12221452 Control Module fits certain Chevrolet Impala, Monte Carlo models.
The original GM component designated by manufacturer part number 12221452 maintains top performance when functioning as the Module Assembly, Electronic Brake & Traction Control; ABS Control Module unit. The component 12221452 is constructed from durable material and its dimensions span 7.1 x 6.1 x 4.1 inches while weighing 1.30 Pounds. The component is ready in New condition to ensure full compatibility with your vehicle system. The part 12221452 has available replacement options listed under 18078147. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.