Menu
×
Search Bar
Search by Part Number, Part Name, or Vehicle
My Garage
Cart
Help Center Contact Us
Make sure this part fits

GM 15767446
Control Module

2000-2003 GM

Customer Questions & Expert Answers (5)
GM 15767446 Control Module
  • Part Description
    Module, Electronic Control Suspension
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits

  • 15767446 Control Module is Ref No. 1 in the diagram below

    2003 Chevy Tahoe Control Module Diagram for 15767446
    The diagram listed above is for your reference. View diagram for your vehicle

    Related Parts for 15767446

  • Vehicle Fitment

    Year Make Model Trim Engine
    2002-2003 Cadillac EscaladeBase8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
    2000-2003 Chevrolet TahoeBase, LS, LT, Z718 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
    2000-2003 GMC YukonDenali, SLE, SLT8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
    Warning: California's Proposition 65

  • Customer Questions & Expert Answers

    Q:
    Is this 15767446 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 15767446 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the Electronic Suspension Control Module on Cadillac Escalade? Posted by Customer
    A:
    You need to reach the control module by first pulling the seat handle at the rear then taking away the retainers from the control module cover before removing the cover from the vehicle. Unplug the wiring harness from the control module then take out the control module from its position inside the vehicle. Put the control module into the vehicle position before hooking up the wiring harness to its designated spot on the control module. The process to complete RTD module programming involves a scan tool connected to the data link connector (DLC) with ignition ON but engine OFF followed by the selection of SPECIAL FUNCTIONS for the RTD module on the scan tool and execution of the instructions in order to complete RTD module programming. You should access SPECIAL FUNCTIONS through the scan tool after completion of programming to execute ALC trimset instructions according to the display. Reinstall the cover while utilizing the retainers designed for the control module cover followed by seating the roll-down mechanism to its original posture.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to Replace the Suspension Control Module on Cadillac Escalade? Posted by Customer
    A:
    In order to replace the Electronic Suspension Control Module in a Tahoe, a Yukon, or Escalade, take off the right side interior trim panel and disconnect the electrical connectors from the module, and remove the screw. Your next step is to slide the module from the bracket and remove it from the vehicle. For installation, slide in the new module in the bracket, installing the screw by using a 1.6 Nm (14 inch lb.). Make the connection of the electrical connectors to the module. Recalibrate it if you are replacing the module by connecting the scan tool to the Data Line Connector (DLC) and turning the ignition ON with the engine OFF and refer to instructions on scan tool readout. Lastly, install the right side interior trim panel.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to service the Suspension Control Module on Chevrolet Tahoe? Posted by Customer
    A:
    To service the Suspension Control Module you should remove the right side interior trim panel on your vehicle type. Take off the bolt and the electrical connectors from the module. Slide the module out of the bracket and remove it from the vehicle. For installation, slide in the new module into the bracket and wrench the screw (15mm) at 1.6Nm (14 inch lbs). Resolder the module's electrical connectors. In the case of replacing the module, calibrate by connecting the scan tool to the Data Line Connector (DLC) when the ignition is turned ON with the engine OFF, following the scan tool instruction. Lastly, install the right side interior trim panel which is appropriate for the type of your vehicle.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the Electronic Suspension Control Module on Chevrolet Tahoe? Posted by Customer
    A:
    The first step to replace the Electronic Suspension Control Module in Tahoe, Yukon and Escalade models involves removing the right interior trim panel. Use a multimeter to detach power supply wires from the module before unscrewing it from the bracket until it frees from the vehicle completely. Place the replacement module into the bracket after which you should install the screw before tightening it to 1.6 Nm (14 inch lbs.). You should attach the electrical connectors back to the module. To replace the module you must perform calibration through the Data Line Connector (DLC) by connecting the scan tool and turning the ignition ON with the engine OFF followed by the scan tool instructions. The right side interior trim panel requires installation as the final step.
    Posted by ChevyPartsGiant Specialist
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Control Module 15767446 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 15767446 Control Module is available in the market under the name GM Suspension Control Module. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 15767446 Control Module fits certain Chevrolet Tahoe models, as well as GMC Yukon. Additionally, it is compatible with Cadillac Escalade models.
The original GM component designated by manufacturer part number 15767446 maintains top performance when functioning as the Module, Electronic Control Suspension unit. The component 15767446 is constructed from durable material and its dimensions span 10.6 x 7.2 x 2.6 inches while weighing 1.90 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. The part 15767446 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.