Make sure this part fits

GM 17989117
Ball Joint, Front Lower

1989-2001 GM

Customer Questions & Expert Answers (2)
GM 17989117 Ball Joint, Front Lower
GM 17989117 Ball Joint, Front Lower
  • Part Description
    Stud Kit, Front Lower Control Arm Ball; Suspension Ball Joint
  • Position
    Front Lower
  • Manufacturer
    General Motors
Make sure this part fits
$45.54 MSRP: $71.33
You Save: $25.79 (37%)
Ships in 1-3 Business Days
1
ADD TO CART
  • Vehicle Fitment

    Year Make Model Trim Engine
    1989-1996 Buick RegalCustom, Gran Sport, Limited, Olympic Gold Edition6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
    1990-2001 Chevrolet LuminaBase, Euro, LS, LTZ, Z344 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.1 L FLEX, 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
    1995-1999 Chevrolet Monte CarloIndianapolis 500 Pace Car, LS, Z346 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
    1997 Oldsmobile CutlassGLS6 Cyl 3.1 L GAS
    1989-1997 Oldsmobile Cutlass SupremeBase, International, S, SL4 Cyl 2.3 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS
    1989-1996 Pontiac Grand PrixBase, GT, GTP, LE, Mclaren, SE, STE4 Cyl 2.3 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 17989117 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 17989117 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to service and repair a ball joint on Chevrolet Lumina? Posted by Customer
    A:
    Start work on the Ball Joint after properly lifting and securing the vehicle under it. Take off the wheel and tire before removing the Ball Joint heat shield bolts then the heat shield itself. First loosen the stabilizer shaft bushing bolts but keep them installed. Then take out the lower Ball Joint cotter pin and nut. Boost your project with the Ball Joint remover/tie rod puller tool j 35917 to disconnect the Ball Joint from the lower Control Arm. When taking out the Ball Joint from its knuckle base make sure to avoid harming the drive axle boots. Begin with a 1/8 inch drill bit to create pilot holes before advancing to a 1/2 inch drill bit. Place the new Ball Joint in the knuckle/strut and secure it according to the Ball Joint kit instructions. Install and tighten the four Ball Joint bolts and nuts progressively to 19 nm (14 ft. Lbs.). Tighten the Ball Joint stud nut onto the lower Control Arm until its next slot fits the cotter pin hole on the Ball Joint near 1 flat (60 degrees) without exceeding 60 degrees of rotation. Fasten the new Ball Joint using the lower Control Arm and torque the stabilizer shaft bushing clamps to 48 nm (35 ft. Lbs.) and the lower Ball Joint nut to 85 nm (63 ft. Lbs.). Place a fresh cotter pin through the new Ball Joint nut and restock the Ball Joint shield before you secure its bolts at 7 nm (62 inch lbs.). Put back the tire and wheel assembly last as you bring the car down to ground level.
    Posted by ChevyPartsGiant Specialist
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Ball Joint, Front Lower 17989117 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 17989117 Ball Joint, Front Lower is available in the market under the name GM Ball Joint. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 17989117 Ball Joint, Front Lower fits certain Chevrolet Lumina, Monte Carlo models, as well as Buick Regal. Additionally, it is compatible with Pontiac Grand Prix and Oldsmobile Cutlass, Cutlass Supreme models.
The original GM component designated by manufacturer part number 17989117 maintains top performance when functioning as the Stud Kit, Front Lower Control Arm Ball; Suspension Ball Joint unit at its Front Lower. The component 17989117 is constructed from durable material and its dimensions span 6.8 x 4.6 x 3.4 inches while weighing 1.60 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Lower Ball Joint; Stud Kit, Front Wheel Lower Control Arm. The part 17989117 has available replacement options. Each vehicle needs 2 units of the part marked as SKU 17989117. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.