Make sure this part fits

GM 10424858
Brake Switch

1999-2005 GM

Customer Questions & Expert Answers (13)
GM 10424858 Brake Switch
GM 10424858 Brake Switch
  • Part Description
    Switch, Stop Lamp Switch; Brake Light Switch
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    1999-2005 Buick CenturyCustom, Limited, Special Edition6 Cyl 3.1 L GAS
    1999-2004 Buick RegalGS, GSE, LS, LSE6 Cyl 3.8 L GAS
    1999-2002 Chevrolet CamaroBase, Z28, Z28 SS6 Cyl 3.8 L GAS, 8 Cyl 5.7 L GAS
    1999-2002 Oldsmobile IntrigueGL, GLS, GX6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS
    1999-2002 Pontiac FirebirdBase, Formula, Trans Am6 Cyl 3.8 L GAS, 8 Cyl 5.7 L GAS
    1999-2003 Pontiac Grand PrixGT, GTP, SE6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 10424858 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 10424858 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to Replace the Brake Light Switch for the Torque Converter Clutch/Cruise Control on Buick Regal? Posted by Customer
    A:
    Start the procedure of Torque Converter Clutch/Cruise Control Release Switch replacement by removing the left instrument panel insulator. The installation process begins by detaching the electrical connector from the cruise release switch followed by switching out the switch from its retainer on the brake pedal bracket. You should start by placing the cruise release switch onto the retainer attached to the brake pedal bracket before you reconnect the electrical connector. Manual adjustment of the cruise release switch follows after installing the left side instrument panel insulator.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to service the brake light switch on Buick Century? Posted by Customer
    A:
    Begin the brake light switch service task by taking off the driver's instrument panel insulator. Take off the electrical connectors before taking the stoplamp switch out from the brake pedal bracket assembly. Reconnect both electrical connections before putting the stoplamp switch back onto its designated position on the brake pedal bracket. Reinstall the driver side instrument panel insulator now. Close the stoplamp switch to its proper position at the end.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to Replace the Brake Light Switch for Cruise Control on Buick Regal? Posted by Customer
    A:
    Begin the replacement of the cruise release switch by taking out the insulator on the left instrument panel. The first step should be to disconnect the cruise release switch electrical connector then remove the switch from the brake pedal bracket retainer. The cruise release switch replacement includes putting the brake pedal bracket retainer back in its position while you reconnect the electrical connector. Complete the replacement by installing the left side instrument panel insulator after customizing the cruise release switch.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the Brake Light Switch for Cruise Control on Chevrolet Camaro? Posted by Customer
    A:
    The replacement of the cruise control release switch starts with sound insulator extraction from the left half of the instrument panel. Before switching out the cruise control release switch disconnect its electrical connector and subsequently discard the switch unit. Depress the Brake Pedal first then insert the cruise control release switch into its bracket until the retainer reaches full seating position. Plug the electrical cable into the cruise control release switch before setting its position properly. The last installation step requires reinstallation of the left instrument panel sound insulator.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to service and repair the brake light switch on Chevrolet Camaro? Posted by Customer
    A:
    Start Brake Light Switch work by taking off the left side instrument panel insulator. Take off the Stoplamp and TCC switch device from its bracket by disconnecting the electrical power connection. Put back the electrical wire to the switch while attaching its body part to the bracket. Set the Stoplamp and TCC switch for proper performance before replacing the left side instrument panel insulator.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be done after removing the I/P insulator for the 2003 Buick Century? Posted by Customer
    A:
    Disconnect the electrical connector from the stop lamp switch.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Light Switch
    Q:
    What should be done after installing the stop lamp switch for the 2002 Buick Century? Posted by Customer
    A:
    Connect the electrical connector to the stop lamp switch.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Light Switch
    Q:
    What is the first step for installation of the stop lamp switch for the 2005 Buick Century? Posted by Customer
    A:
    Begin by installing the stop lamp switch back onto the brake pedal bracket.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Light Switch
    Q:
    How do you remove the cruise release switch for the 2001 Buick Century? Posted by Customer
    A:
    Remove the switch from its retainer on the brake pedal bracket.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Light Switch
    Q:
    What is the first step to replace the stoplamp switch for the 2001 Buick Regal? Posted by Customer
    A:
    First, remove the left side instrument panel insulator.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Light Switch
    Q:
    What is the final step in the process for the 2001 Chevrolet Camaro? Posted by Customer
    A:
    Reinstall the left instrument panel sound insulator.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Light Switch
    Q:
    What should be done after removing the instrument panel insulator for the 2002 Chevrolet Camaro? Posted by Customer
    A:
    Disconnect the electrical connector from the switch and remove the stop lamp and Torque Converter Clutch switch from the bracket.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Light Switch
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Brake Switch 10424858 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 10424858 Brake Switch is available in the market under the name GM Brake Light Switch. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 10424858 Brake Switch fits certain Chevrolet Camaro models, as well as Buick Regal, Century. Additionally, it is compatible with Pontiac Firebird, Grand Prix and Oldsmobile Intrigue models.
The original GM component designated by manufacturer part number 10424858 maintains top performance when functioning as the Switch, Stop Lamp Switch; Brake Light Switch unit. The component 10424858 is constructed from durable material and its dimensions span 4.1 x 2.2 x 2.1 inches while weighing 0.40 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Release Switch; Stoplamp Switch. The part 10424858 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.